Add support for the I2C controller on the RTL9300 SoC. There are two I2C
controllers in the RTL9300 that are part of the Ethernet switch register
block. Each of these controllers owns a SCL pin (GPIO8 for the fiorst
I2C controller, GPIO17 for the second). There are 8 possible SDA pins
(GPIO9-16) that can be assigned to either I2C controller. This
relationship is represented in the device tree with a child node for
each SDA line in use.
This is based on the openwrt implementation[1] but has been
significantly modified
[1] - https://git.openwrt.org/?p=openwrt/openwrt.git;a=blob;f=target/linux/realtek/files-5.15/drivers/i2c/busses/i2c-rtl9300.c
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The removal of the supply clock rate check implies a need to remove
some unnecessary left-over data from the driver as well.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
While at it, fix an obvious typo in help section of the Kconfig.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Some S32G2/S32G3 SoC I2C particularities exist
such as different <clock divider, register value> pairs.
Those are addressed by adding specific S32G2 and S32G3
compatible strings.
Co-developed-by: Ionut Vicovan <Ionut.Vicovan@nxp.com>
Signed-off-by: Ionut Vicovan <Ionut.Vicovan@nxp.com>
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
S32G2 and S32G3 SoCs use the same I2C controller as i.MX.
But there are small differences such as specific
<clock divider, register value> pairs.
So add new compatible strings 'nxp,s32g2-i2c'and 'nxp,s32g3-i2c'
for S32G2/S32G3 Socs.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The i2c-amd756-s4882 and i2c-nforce2-s4985 muxing pseudo-drivers were
written at a time when the i2c core did not support muxing. They are
essentially board-specific hacks. If we had to add support for these
boards today, we would implement it in a completely different way.
These Tyan server boards are 19 years old by now, so I very much doubt
any of these is still running today. So let's just drop this clumsy
code. If anyone really still needs this support and complains, I'll
rewrite it in a proper way on top of i2c-mux.
This also fixes the following warnings:
drivers/i2c/busses/i2c-amd756.c:286:20: warning: symbol 'amd756_smbus' was not declared. Should it be static?
drivers/i2c/busses/i2c-nforce2.c:123:20: warning: symbol 'nforce2_smbus' was not declared. Should it be static?
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Andi Shyti <andi.shyti@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
We are experiencing a problem with the i.MX I2C controller when
communicating with SMBus devices. We are seeing devices time-out because
the time between sending/receiving two bytes is too long, and the SMBus
device returns to the idle state. This happens because the i.MX I2C
controller sends and receives byte by byte. When a byte is sent or
received, we get an interrupt and can send or receive the next byte.
The current implementation sends a byte and then waits for an event
generated by the interrupt subroutine. After the event is received, the
next byte is sent and we wait again. This waiting allows the scheduler
to reschedule other tasks, with the disadvantage that we may not send
the next byte for a long time because the send task is not immediately
scheduled. For example, if the rescheduling takes more than 25ms, this
can cause SMBus devices to timeout and communication to fail.
This patch changes the behavior so that we do not reschedule the
send/receive task, but instead send or receive the next byte in the
interrupt subroutine. This prevents rescheduling and drastically reduces
the time between sending/receiving bytes. The cost in the interrupt
subroutine is relatively small, we check what state we are in and then
send/receive the next byte. Before we had to call wake_up, which is even
less expensive. However, we also had to do some scheduling, which
increased the overall cost compared to the new solution. The wake_up
function to wake up the send/receive task is now only called when an
error occurs or when the transfer is complete.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Separate the atomic, dma and non-dma use case as a preparation step for
moving the non-dma use case to the isr to avoid rescheduling while a
transfer is in progress.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
According to the i.MX8M Mini reference manual chapter "16.1.4.2
Generation of Start" it is only necessary to poll for bus busy and
arbitration lost in multi master mode. This helps to avoid rescheduling
while the i2c bus is busy and avoids SMBus devices to timeout. For
backward compatibility, the single-master property needs to be
explicitly set to disable the bus busy polling.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The to-be-fixed commit rightfully reduced a race window, but also
removed a comment which is still helpful after the fix. Bring the
comment back.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/i2c to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
In existing socs, I2C serial engine is sourced from XO (19.2MHz).
Where as in IPQ5424, I2C serial engine is sourced from GPLL0 (32MHz).
The existing map table is based on 19.2MHz. This patch incorporates
the clock map table to derive the SCL clock from the 32MHz source
clock frequency.
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
It is common practice in the downstream and upstream CCI dt to set CCI
clock rates to 19.2 MHz. It appears to be fairly common for initial code to
set the CCI clock rate to 37.5 MHz.
Applying the widely used CCI clock rates from downstream ought not to cause
warning messages in the upstream kernel where our general policy is to
usually copy downstream hardware clock rates across the range of Qualcomm
drivers.
Drop the warning it is pervasive across CAMSS users but doesn't add any
information or warrant any changes to the DT to align the DT clock rate to
the bootloader clock rate.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/linux-arm-msm/20240824115900.40702-1-bryan.odonoghue@linaro.org
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
If not clearing the BB (bus busy) condition in the BER (bus error)
interrupt, the driver causes a timeout and hence the i2c core
doesn't do the i2c transfer retry but returns the driver's return
value to the upper layer instead.
Clear the BB condition in the BER interrupt and a software flag is
used. The driver does an i2c recovery without causing the timeout
if the flag is set.
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Originally the driver uses the XMIT bit in SMBnST register to decide
the upcoming i2c transaction. If XMIT bit is 1, then it will be an i2c
write operation. If it's 0, then a read operation will be executed.
In slave mode the XMIT bit can simply be used directly to set the state.
XMIT bit can be used as an indication to the current state of the state
machine during slave operation. (meaning XMIT = 1 during writing and
XMIT = 0 during reading).
In master operation XMIT is valid only if there are no bus errors.
For example: in a multi master where the same module is switching from
master to slave at runtime, and there are collisions, the XMIT bit
cannot be trusted.
However the maser already "knows" what the bus state is, so this bit
is not needed and the driver can just track what it is currently doing.
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Currently the PCI glue driver uses sda_hold variable name, while
the rest of the driver use sda_hold_time. This makes things harder
to grep. Use sda_hold_time variable name everywhere.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
To ensure successive interrupts upon packet reception, it is necessary to
clear the remote IRR bit by writing the interrupt number to the EOI
register. The base address for this operation is provided by the BIOS and
retrieved by the driver by traversing the ASF object's namespace.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Implement the i2c_algorithm operations to enable support for AMD ASF
(Alert Standard Format) with SMBus. This enhancement includes:
- Adding functionality to identify and select the supported ASF functions.
- Implementing mechanisms for registering and deregistering I2C slave
devices.
- Providing support for data transfer operations over ASF.
Additionally, include a 'select' Kconfig entry as the current patch
utilizes .reg_slave() and .unreg_slave() callbacks, which are controlled
by CONFIG_I2C_SLAVE.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The AMD ASF controller is presented to the operating system as an ACPI
device. The AMD ASF driver can use ACPI to obtain information about the
ASF controller's attributes, such as the ASF address space and interrupt
number, and to handle ASF interrupts.
Currently, the piix4 driver assumes that a specific port address is
designated for AUX operations. However, with the introduction of ASF, the
same port address may also be used by the ASF controller. Therefore, a
check needs to be added to ensure that if ASF is advertised and enabled in
ACPI, the AUX port should not be configured.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Export the following i2c_piix4 driver functions as a library so that the
AMD ASF driver can utilize these core functionalities from the i2c_piix4
driver:
- piix4_sb800_region_request(): Request access to a specific SMBus region
on the SB800 chipset.
- piix4_sb800_region_release(): Release the previously requested SMBus
region on the SB800 chipset.
- piix4_transaction(): Handle SMBus transactions between the SMBus
controller and connected devices.
- piix4_sb800_port_sel(): Select the appropriate SMBus port on the SB800
chipset.
By making these functions available as a library, enable the AMD ASF
driver to leverage the established mechanisms in the i2c_piix4 driver,
promoting code reuse and consistency across different drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add a separate header file to relocate the common code from the i2c_piix4
driver, allowing the AMD ASF driver to utilize the same code.
Update the MAINTAINERS file to include information about the new common
header file.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Currently, `piix4_transaction()` accepts only one parameter, which is the
`i2c_adapter` information. This approach works well as long as SB800 SMBus
port accesses are confined to the piix4 driver. However, with the
implementation of a separate ASF driver and the varying address spaces
across drivers, it is necessary to change the function parameter list of
`piix4_transaction()` to include the port address. This modification
allows other drivers that use piix4 to pass the specific port details they
need to operate on.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Convert existing descriptions to kernel-doc format and unify
the rest of the comments to follow the modern style.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Octal permissions are preferred over the symbolics ones
for readbility. This ceases warning message pointed by checkpatch.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There are two different names used for the variable that holds
an error code. Unify to use one variant in all cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Introduce a temporary variable to hold a device pointer.
It can be utilized in the ->probe() and save a bit of LoCs.
To make it consistent, rename currently used dev to pdev.
While at it, convert the only error message to dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Switch from i2c_add_adapter() to resource managed devm_i2c_add_adapter()
for matching rest of driver initialization, and more concise code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Use custom private data structure instead of global variables.
With that, remove not anymore true comment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There are a lot of messaging calls that use global variable of
struct i2c_adapter. Instead, to make code better and flexible
for further improvements, pass the pointer to the actual adapter
used for transfers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Rework the read and write code paths in the driver to support operation
in atomic contexts in master mode. This change does not apply to slave
mode because there is no way to handle interruptions in that context.
Adjust the message timeout to include some extra time. For non-atomic
contexts, 500 ms is added to the timeout. For atomic contexts,
2000 ms is added because transfers happen in polled mode, requiring
more time to account for the polling overhead.
Similar changes have been implemented in other drivers, including:
commit 3a5ee18d2a ("i2c: imx: implement master_xfer_atomic callback")
commit 445094c8a9 ("i2c: exynos5: add support for atomic transfers")
commit ede2299f71 ("i2c: tegra: Support atomic transfers")
commit fe402bd090 ("i2c: meson: implement the master_xfer_atomic
callback")
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The cdns_i2c_master_xfer function has been refactored to separate
the common code. This change facilitates better support for atomic
mode operations by isolating the shared logic.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Chris Packham