commit c6cc25fda5 upstream.
The adp5520 unfortunately also clears the BL_EN bit when the nSTNDBY bit is
cleared. So we need to make sure to restore it during resume if it was set
before suspend.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdbc5d0c60 upstream.
The driver is doing, by default, multi-block reads. When a block error
occurs, card/block.c instigates a single block read: "mmcblk0: retrying
using single block read". It leaves the sg chain intact and just changes
the length attribute for the first sg entry and the overall sg_len
parameter. When atmci_read_data_pio is called to read the single block
of data it ignores the sg_len and expects to read more than 512 bytes as
it sees there are multiple items in the sg list. No more data comes as
the controller has only been commanded to get one block.
Signed-off-by: Terry Barnaby <terry@beam.ltd.uk>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 836dc2fe89 upstream.
PARTITION_SUPPORT needs to be set before doing the compare on version
number so the bit width test does not get invalid data. Before this
patch, a Sandisk iNAND eMMC card would detect 1-bit width although
the hardware supports 4-bit.
Only affects old emmc devices - pre 4.4 devices.
Reported-by: Elad Yi <elad.yi@gmail.com>
Signed-off-by: Philip Rakity <prakity@yahoo.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 660696d1d1 upstream.
Source operand for one byte mov[zs]x is decoded incorrectly if it is in
high byte register. Fix that.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91cf54feec upstream.
Fix regression introduced by commit 796211b795 ("mmc: atmel-mci: add
pdc support and runtime capabilities detection") which removed the need
for CONFIG_MMC_ATMELMCI_DMA but kept the Kconfig-entry as well as the
compile guards around dma_release_channel() in remove(). Consequently,
DMA is always enabled (if supported), but the DMA-channel is not
released on module unload unless the DMA-config option is selected.
Remove the no longer used CONFIG_MMC_ATMELMCI_DMA option completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f3e3c7cfc upstream.
Fox the Kconfig documentation for CONFIG_EXT4_DEBUG to match the
change made by commit a0b30c1229: ext4: use module parameters instead
of debugfs for mballoc_debug
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5c72d814c upstream.
Commit fb0a387dcd restricts block allocations for indirect-mapped
files to block groups less than s_blockfile_groups. However, the
online resizing code wasn't setting s_blockfile_groups, so the newly
added block groups were not available for non-extent mapped files.
Reported-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d76a3a7711 upstream.
In the case where an inode has a very stale transaction id (tid) in
i_datasync_tid or i_sync_tid, it's possible that after a very large
(2**31) number of transactions, that the tid number space might wrap,
causing tid_geq()'s calculations to fail.
Commit deeeaf13 "jbd2: fix fsync() tid wraparound bug", later modified
by commit e7b04ac0 "jbd2: don't wake kjournald unnecessarily",
attempted to fix this problem, but it only avoided kjournald spinning
forever by fixing the logic in jbd2_log_start_commit().
Unfortunately, in the codepaths in fs/ext4/fsync.c and fs/ext4/inode.c
that might call jbd2_log_start_commit() with a stale tid, those
functions will subsequently call jbd2_log_wait_commit() with the same
stale tid, and then wait for a very long time. To fix this, we
replace the calls to jbd2_log_start_commit() and
jbd2_log_wait_commit() with a call to a new function,
jbd2_complete_transaction(), which will correctly handle stale tid's.
As a bonus, jbd2_complete_transaction() will avoid locking
j_state_lock for writing unless a commit needs to be started. This
should have a small (but probably not measurable) improvement for
ext4's scalability.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Reported-by: George Barnett <gbarnett@atlassian.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78d77df715 upstream.
During early init, we would incorrectly set the NX bit even if the NX
feature was not supported. Instead, only set this bit if NX is
actually available and enabled. We already do very early detection of
the NX bit to enable it in EFER, this simply extends this detection to
the early page table mask.
Reported-by: Fernando Luis Vázquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1367476850.5660.2.camel@nexus
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73e3dd6b45 upstream.
The PTP Hardware Clock settime function in the e1000e driver
computes nanoseconds from a struct timespec. The code converts the
seconds field .tv_sec by multiplying it with NSEC_PER_SEC. However,
both operands are of type long, resulting in an unintended overflow.
The patch fixes the issue by using the helper function from time.h.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d87d830720 upstream.
Previously, the ixgbe_msix_other was writing the full 32bits of the set
interrupts, instead of only the ones which the ixgbe_msix_other is
handling. This resulted in a loss of performance when the X540's PPS feature is
enabled due to sometimes clearing queue interrupts which resulted in the driver
not getting the interrupt for cleaning the q_vector rings often enough. The fix
is to simply mask the lower 16bits off so that this handler does not write them
in the EICR, which causes them to remain high and be properly handled by the
clean_rings interrupt routine as normal.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d69f3bad46 upstream.
Trying to run an application which was trying to put data into half of
memory using shmget(), we found that having a shmall value below 8EiB-8TiB
would prevent us from using anything more than 8TiB. By setting
kernel.shmall greater than 8EiB-8TiB would make the job work.
In the newseg() function, ns->shm_tot which, at 8TiB is INT_MAX.
ipc/shm.c:
458 static int newseg(struct ipc_namespace *ns, struct ipc_params *params)
459 {
...
465 int numpages = (size + PAGE_SIZE -1) >> PAGE_SHIFT;
...
474 if (ns->shm_tot + numpages > ns->shm_ctlall)
475 return -ENOSPC;
[akpm@linux-foundation.org: make ipc/shm.c:newseg()'s numpages size_t, not int]
Signed-off-by: Robin Holt <holt@sgi.com>
Reported-by: Alex Thorlton <athorlton@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 990de49f74 upstream.
When a full scan 2.4 and 5 GHz scan is scheduled, but then the 2.4 GHz
part of the scan disables a 5.2 GHz channel due to, e.g. receiving
country or frequency information, that 5.2 GHz channel might already
be in the list of channels to scan next. Then, when the driver checks
if it should do a passive scan, that will return false and attempt an
active scan. This is not only wrong but can also lead to the iwlwifi
device firmware crashing since it checks regulatory as well.
Fix this by not setting the channel flags to just disabled but rather
OR'ing in the disabled flag. That way, even if the race happens, the
channel will be scanned passively which is still (mostly) correct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf8d909705 upstream.
The seconds field of an nfstime4 structure is 64bit, but we are assuming
that the first 32bits are zero-filled. So if the client tries to set
atime to a value before the epoch (touch -t 196001010101), then the
server will save the wrong value on disk.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c7c3e67ab upstream.
Don't actually close any opens until we don't need them at all.
This means being left with write access when it's not really necessary,
but that's better than putting a file that might still have posix locks
held on it, as we have been.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b6cc4d6f8 upstream.
A server shouldn't normally return NFS4ERR_GRACE if the client holds a
delegation, since no conflicting lock reclaims can be granted, however
the spec does not require the server to grant the open in this
instance
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbb21c25a3 upstream.
A server shouldn't normally return NFS4ERR_GRACE if the client holds a
delegation, since no conflicting lock reclaims can be granted, however
the spec does not require the server to grant the lock in this
instance.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32f9f570d0 upstream.
In SSD/hard disk hybid storage, discard request should be ignored for hard
disk. We used to be doing this way, but the unplug path forgets it.
This is suitable for stable tree since v3.6.
Reported-and-tested-by: Markus <M4rkusXXL@web.de>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 486adf72cc upstream.
Maintenance of a bad-block-list currently defaults to 'enabled'
and is then disabled when it cannot be supported.
This is backwards and causes problem for dm-raid which didn't know
to disable it.
So fix the defaults, and only enabled for v1.x metadata which
explicitly has bad blocks enabled.
The problem with dm-raid has been present since badblock support was
added in v3.1, so this patch is suitable for any -stable from 3.1
onwards.
Reported-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dfd89af86 upstream.
After a server reboot, the reclaimer thread will recover all the existing
locks. For locks that are blocked, however, it will change the value
of block->b_status to nlm_lck_denied_grace_period in order to signal that
they need to wake up and resend the original blocking lock request.
Due to a bug, however, the block->b_status never gets reset after the
blocked locks have been woken up, and so the process goes into an
infinite loop of resends until the blocked lock is satisfied.
Reported-by: Marc Eshel <eshel@us.ibm.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e56fb28740 upstream.
threadgroup_lock() takes signal->cred_guard_mutex to ensure that
thread_group_leader() is stable. This doesn't look nice, the scope of
this lock in do_execve() is huge.
And as Dave pointed out this can lead to deadlock, we have the
following dependencies:
do_execve: cred_guard_mutex -> i_mutex
cgroup_mount: i_mutex -> cgroup_mutex
attach_task_by_pid: cgroup_mutex -> cred_guard_mutex
Change de_thread() to take threadgroup_change_begin() around the
switch-the-leader code and change threadgroup_lock() to avoid
->cred_guard_mutex.
Note that de_thread() can't sleep with ->group_rwsem held, this can
obviously deadlock with the exiting leader if the writer is active, so it
does threadgroup_change_end() before schedule().
Reported-by: Dave Jones <davej@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 421348f1ca upstream.
Call cond_resched() in shrink_dcache_parent() to maintain interactivity.
Before this patch:
void shrink_dcache_parent(struct dentry * parent)
{
while ((found = select_parent(parent, &dispose)) != 0)
shrink_dentry_list(&dispose);
}
select_parent() populates the dispose list with dentries which
shrink_dentry_list() then deletes. select_parent() carefully uses
need_resched() to avoid doing too much work at once. But neither
shrink_dcache_parent() nor its called functions call cond_resched(). So
once need_resched() is set select_parent() will return single dentry
dispose list which is then deleted by shrink_dentry_list(). This is
inefficient when there are a lot of dentry to process. This can cause
softlockup and hurts interactivity on non preemptable kernels.
This change adds cond_resched() in shrink_dcache_parent(). The benefit
of this is that need_resched() is quickly cleared so that future calls
to select_parent() are able to efficiently return a big batch of dentry.
These additional cond_resched() do not seem to impact performance, at
least for the workload below.
Here is a program which can cause soft lockup if other system activity
sets need_resched().
int main()
{
struct rlimit rlim;
int i;
int f[100000];
char buf[20];
struct timeval t1, t2;
double diff;
/* cleanup past run */
system("rm -rf x");
/* boost nfile rlimit */
rlim.rlim_cur = 200000;
rlim.rlim_max = 200000;
if (setrlimit(RLIMIT_NOFILE, &rlim))
err(1, "setrlimit");
/* make directory for files */
if (mkdir("x", 0700))
err(1, "mkdir");
if (gettimeofday(&t1, NULL))
err(1, "gettimeofday");
/* populate directory with open files */
for (i = 0; i < 100000; i++) {
snprintf(buf, sizeof(buf), "x/%d", i);
f[i] = open(buf, O_CREAT);
if (f[i] == -1)
err(1, "open");
}
/* close some of the files */
for (i = 0; i < 85000; i++)
close(f[i]);
/* unlink all files, even open ones */
system("rm -rf x");
if (gettimeofday(&t2, NULL))
err(1, "gettimeofday");
diff = (((double)t2.tv_sec * 1000000 + t2.tv_usec) -
((double)t1.tv_sec * 1000000 + t1.tv_usec));
printf("done: %g elapsed\n", diff/1e6);
return 0;
}
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04df32fa10 upstream.
When we run the crackerjack testsuite, the inotify_add_watch test is
stalled.
This is caused by the invalid mask 0 - the task is waiting for the event
but it never comes. inotify_add_watch() should return -EINVAL as it did
before commit 676a0675cf ("inotify: remove broken mask checks causing
unmount to be EINVAL"). That commit removes the invalid mask check, but
that check is needed.
Check the mask's ALL_INOTIFY_BITS before the inotify_arg_to_mask() call.
If none are set, just return -EINVAL.
Because IN_UNMOUNT is in ALL_INOTIFY_BITS, this change will not trigger
the problem that above commit fixed.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Acked-by: Jim Somerville <Jim.Somerville@windriver.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Eric Paris <eparis@parisplace.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cc1144a31 upstream.
mkinitrd looks at /sys/class/scsi_host/host$hostnum/proc_name to find
the module name of a disk driver. Current name is "highbank-ahci" but
the module is "sata_highbank". Rename it to match the module name.
Signed-off-by: Robert Richter <robert.richter@calxeda.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f7a05d701 upstream.
Vitaliy reported that a per cpu HPET timer interrupt crashes the
system during hibernation. What happens is that the per cpu HPET timer
gets shut down when the nonboot cpus are stopped. When the nonboot
cpus are onlined again the HPET code sets up the MSI interrupt which
fires before the clock event device is registered. The event handler
is still set to hrtimer_interrupt, which then crashes the machine due
to highres mode not being active.
See http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=700333
There is no real good way to avoid that in the HPET code. The HPET
code alrady has a mechanism to detect spurious interrupts when event
handler == NULL for a similar reason.
We can handle that in the clockevent/tick layer and replace the
previous functional handler with a dummy handler like we do in
tick_setup_new_device().
The original clockevents code did this in clockevents_exchange_device(),
but that got removed by commit 7c1e76897 (clockevents: prevent
clockevent event_handler ending up handler_noop) which forgot to fix
it up in tick_shutdown(). Same issue with the broadcast device.
Reported-by: Vitaliy Fillipov <vitalif@yourcmc.ru>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: 700333@bugs.debian.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ced9cb1af1 upstream.
A bug was reported that caused localmodconfig to not keep all the
dependencies of ATH9K. This was caused by the kconfig file:
In drivers/net/wireless/ath/Kconfig:
commit 712317ad97 upstream.
We should store file xattrs in struct cfent instead of struct cftype,
because cftype is a type while cfent is object instance of cftype.
For example each cgroup has a tasks file, and each tasks file is
associated with a uniq cfent, but all those files share the same
struct cftype.
Alexey Kodanev reported a crash, which can be reproduced:
# mount -t cgroup -o xattr /sys/fs/cgroup
# mkdir /sys/fs/cgroup/test
# setfattr -n trusted.value -v test_value /sys/fs/cgroup/tasks
# rmdir /sys/fs/cgroup/test
# umount /sys/fs/cgroup
oops!
In this case, simple_xattrs_free() will free the same struct simple_xattrs
twice.
tj: Dropped unused local variable @cft from cgroup_diput().
Reported-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ac1707a13 upstream.
The 3rd parameter of flex_array_prealloc() is the number of elements,
not the index of the last element.
The effect of the bug is, when opening cgroup.procs, a flex array will
be allocated and all elements of the array is allocated with
GFP_KERNEL flag, but the last one is GFP_ATOMIC, and if we fail to
allocate memory for it, it'll trigger a BUG_ON().
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94a4093195 upstream.
Commit 4ae46be "Thermal: Introduce thermal_zone_trip_update()"
introduced a regression causing the fan to be always on even when
the system is idle.
My original idea in that commit is that:
- when the current temperature is above the trip point,
keep the fan on, even if the temperature is dropping.
- when the current temperature is below the trip point,
turn on the fan when the temperature is raising,
turn off the fan when the temperature is dropping.
But this is what the code actually does:
- when the current temperature is above the trip point,
the fan keeps on.
- when the current temperature is below the trip point,
the fan is always on because thermal_get_trend()
in driver/acpi/thermal.c returns THERMAL_TREND_RAISING.
Thus the fan keeps running even if the system is idle.
Fix this in drivers/acpi/thermal.c.
[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=56591
References: https://bugzilla.kernel.org/show_bug.cgi?id=56601
References: https://bugzilla.kernel.org/show_bug.cgi?id=50041#c45
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Tested-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6432ded29 upstream.
Commit 53aac44 (ACPI: Store valid ACPI tables passed via early initrd
in reserved memblock areas) introduced acpi_initrd_override() that
passes a wrong value as the second argument to memblock_reserve().
Namely, the second argument of memblock_reserve() is the size of the
region, not the address of the top of it, so make
acpi_initrd_override() pass the size in there as appropriate.
[rjw: Changelog]
Signed-off-by: Wang YanQing <udknight@gmail.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d66af4df08 upstream.
Since commit 30dcf76acc, ata_ap_acpi_handle will always do a namespace
walk, which requires acquiring an acpi namespace mutex. This made it
impossible to be used when calling path has held a spinlock.
For example, it can occur in the following code path for pata_acpi:
ata_scsi_queuecmd (ap->lock is acquired)
__ata_scsi_queuecmd
ata_scsi_translate
ata_qc_issue
pacpi_qc_issue
ata_acpi_stm
ata_ap_acpi_handle
acpi_get_child
acpi_walk_namespace
acpi_ut_acquire_mutex (acquire mutex while holding lock)
This caused scheduling while atomic bug, as reported in bug #56781.
Actually, ata_ap_acpi_handle doesn't have to walk the namespace every
time it is called, it can simply return the bound acpi handle on the
corresponding SCSI host. The reason previously it is not done this way
is, ata_ap_acpi_handle is used in the binding function
ata_acpi_bind_host by ata_acpi_gtm when the handle is not bound to the
SCSI host yet. Since we already have the ATA port's handle in its
binding function, we can simply use it instead of calling
ata_ap_acpi_handle there. So introduce a new function __ata_acpi_gtm,
where it will receive an acpi handle param in addition to the ATA port
which is solely used for debug statement. With this change, we can make
ata_ap_acpi_handle simply return the bound handle for SCSI host instead
of walking the acpi namespace now.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=56781
Reported-and-tested-by: <kenzopl@o2.pl>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e005715efa upstream.
There's a bug where rtc alarms are ignored after the rtc cmos suspends
but before the system finishes suspend. Since hpet emulation is
disabled and it still handles the interrupts, a wake event is never
registered which is done from the rtc layer.
This patch reverts commit d1b2efa83f ("rtc: disable hpet emulation on
suspend") which disabled hpet emulation. To fix the problem mentioned
in that commit, hpet_rtc_timer_init() is called directly on resume.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cdc444a67 upstream.
As pointed out by Andrew Morton, the swap-over-NFS writeback is not
setting PageWriteback before it is queued for direct IO. While swap
pages do not participate in BDI or process dirty accounting and the IO
is synchronous, the writeback bit is still required and not setting it
in this case was an oversight. swapoff depends on the page writeback to
synchronoise all pending writes on a swap page before it is reused.
Swapcache freeing and reuse depend on checking the PageWriteback under
lock to ensure the page is safe to reuse.
Direct IO handlers and the direct IO handler for NFS do not deal with
PageWriteback as they are synchronous writes. In the case of NFS, it
schedules pages (or a page in the case of swap) for IO and then waits
synchronously for IO to complete in nfs_direct_write(). It is
recognised that this is a slowdown from normal swap handling which is
asynchronous and uses a completion handler. Shoving PageWriteback
handling down into direct IO handlers looks like a bad fit to handle the
swap case although it may have to be dealt with some day if swap is
converted to use direct IO in general and bmap is finally done away
with. At that point it will be necessary to refit asynchronous direct
IO with completion handlers onto the swap subsystem.
As swapcache currently depends on PageWriteback to protect against
races, this patch sets PageWriteback under the page lock before queueing
it for direct IO. It is cleared when the direct IO handler returns. IO
errors are treated similarly to the direct-to-bio case except PageError
is not set as in the case of swap-over-NFS, it is likely to be a
transient error.
It was asked what prevents such a page being reclaimed in parallel.
With this patch applied, such a page will now be skipped (most of the
time) or blocked until the writeback completes. Reclaim checks
PageWriteback under the page lock before calling try_to_free_swap and
the page lock should prevent the page being requeued for IO before it is
freed.
This and Jerome's related patch should considered for -stable as far
back as 3.6 when swap-over-NFS was introduced.
[akpm@linux-foundation.org: use pr_err_ratelimited()]
[akpm@linux-foundation.org: remove hopefully-unneeded cast in printk]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d30d31ea3 upstream.
Since commit 62c230bc17 ("mm: add support for a filesystem to activate
swap files and use direct_IO for writing swap pages"), swap_writepage()
calls direct_IO on swap files. However, in that case the page isn't
redirtied if I/O fails, and is therefore handled afterwards as if it has
been successfully written to the swap file, leading to memory corruption
when the page is eventually swapped back in.
This patch sets the page dirty when direct_IO() fails. It fixes a
memory corruption that happened while using swap-over-NFS.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f294b5a13 upstream.
The settimeofday01 test in the LTP testsuite effectively does
gettimeofday(current time);
settimeofday(Jan 1, 1970 + 100 seconds);
settimeofday(current time);
This test causes a stack trace to be displayed on the console during the
setting of timeofday to Jan 1, 1970 + 100 seconds:
[ 131.066751] ------------[ cut here ]------------
[ 131.096448] WARNING: at kernel/time/clockevents.c:209 clockevents_program_event+0x135/0x140()
[ 131.104935] Hardware name: Dinar
[ 131.108150] Modules linked in: sg nfsv3 nfs_acl nfsv4 auth_rpcgss nfs dns_resolver fscache lockd sunrpc nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6table_mangle ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 iptable_nat nf_nat_ipv4 nf_nat iptable_mangle ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter ip_tables kvm_amd kvm sp5100_tco bnx2 i2c_piix4 crc32c_intel k10temp fam15h_power ghash_clmulni_intel amd64_edac_mod pcspkr serio_raw edac_mce_amd edac_core microcode xfs libcrc32c sr_mod sd_mod cdrom ata_generic crc_t10dif pata_acpi radeon i2c_algo_bit drm_kms_helper ttm drm ahci pata_atiixp libahci libata usb_storage i2c_core dm_mirror dm_region_hash dm_log dm_mod
[ 131.176784] Pid: 0, comm: swapper/28 Not tainted 3.8.0+ #6
[ 131.182248] Call Trace:
[ 131.184684] <IRQ> [<ffffffff810612af>] warn_slowpath_common+0x7f/0xc0
[ 131.191312] [<ffffffff8106130a>] warn_slowpath_null+0x1a/0x20
[ 131.197131] [<ffffffff810b9fd5>] clockevents_program_event+0x135/0x140
[ 131.203721] [<ffffffff810bb584>] tick_program_event+0x24/0x30
[ 131.209534] [<ffffffff81089ab1>] hrtimer_interrupt+0x131/0x230
[ 131.215437] [<ffffffff814b9600>] ? cpufreq_p4_target+0x130/0x130
[ 131.221509] [<ffffffff81619119>] smp_apic_timer_interrupt+0x69/0x99
[ 131.227839] [<ffffffff8161805d>] apic_timer_interrupt+0x6d/0x80
[ 131.233816] <EOI> [<ffffffff81099745>] ? sched_clock_cpu+0xc5/0x120
[ 131.240267] [<ffffffff814b9ff0>] ? cpuidle_wrap_enter+0x50/0xa0
[ 131.246252] [<ffffffff814b9fe9>] ? cpuidle_wrap_enter+0x49/0xa0
[ 131.252238] [<ffffffff814ba050>] cpuidle_enter_tk+0x10/0x20
[ 131.257877] [<ffffffff814b9c89>] cpuidle_idle_call+0xa9/0x260
[ 131.263692] [<ffffffff8101c42f>] cpu_idle+0xaf/0x120
[ 131.268727] [<ffffffff815f8971>] start_secondary+0x255/0x257
[ 131.274449] ---[ end trace 1151a50552231615 ]---
When we change the system time to a low value like this, the value of
timekeeper->offs_real will be a negative value.
It seems that the WARN occurs because an hrtimer has been started in the time
between the releasing of the timekeeper lock and the IPI call (via a call to
on_each_cpu) in clock_was_set() in the do_settimeofday() code. The end result
is that a REALTIME_CLOCK timer has been added with softexpires = expires =
KTIME_MAX. The hrtimer_interrupt() fires/is called and the loop at
kernel/hrtimer.c:1289 is executed. In this loop the code subtracts the
clock base's offset (which was set to timekeeper->offs_real in
do_settimeofday()) from the current hrtimer_cpu_base->expiry value (which
was KTIME_MAX):
KTIME_MAX - (a negative value) = overflow
A simple check for an overflow can resolve this problem. Using KTIME_MAX
instead of the overflow value will result in the hrtimer function being run,
and the reprogramming of the timer after that.
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
[jstultz: Tweaked commit subject]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51fd36f3fa upstream.
One can trigger an overflow when using ktime_add_ns() on a 32bit
architecture not supporting CONFIG_KTIME_SCALAR.
When passing a very high value for u64 nsec, e.g. 7881299347898368000
the do_div() function converts this value to seconds (7881299347) which
is still to high to pass to the ktime_set() function as long. The result
in is a negative value.
The problem on my system occurs in the tick-sched.c,
tick_nohz_stop_sched_tick() when time_delta is set to
timekeeping_max_deferment(). The check for time_delta < KTIME_MAX is
valid, thus ktime_add_ns() is called with a too large value resulting in
a negative expire value. This leads to an endless loop in the ticker code:
time_delta: 7881299347898368000
expires = ktime_add_ns(last_update, time_delta)
expires: negative value
This fix caps the value to KTIME_MAX.
This error doesn't occurs on 64bit or architectures supporting
CONFIG_KTIME_SCALAR (e.g. ARM, x86-32).
Signed-off-by: David Engraf <david.engraf@sysgo.com>
[jstultz: Minor tweaks to commit message & header]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65033cc8d5 upstream.
When we have a loopback mixer control, this should manage the state
whether the output paths include the aamix or not. But the current
code blindly initializes the output paths with aamix = true, thus the
aamix is enabled unless the loopback mixer control is changed.
Also, update_aamix_paths() called by the loopback mixer control put
callback invokes snd_hda_activate_path() with aamix = true even for
disabling the mixing. This leaves the aamix path even though the
loopback control is turned off.
This patch fixes these issues:
- Introduced aamix_default() helper to indicate whether with_aamix is
true or false as default
- Fix the argument in update_aamix_paths() for disabling loopback
Reported-by: Lydia Wang <LydiaWang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c75c5ab575 upstream.
The recent changes in the USB API ("implement new semantics for
URB_ISO_ASAP") made the former meaning of the URB_ISO_ASAP flag the
default, and changed this flag to mean that URBs can be delayed.
This is not the behaviour wanted by any of the audio drivers because
it leads to discontinuous playback with very small period sizes.
Therefore, our URBs need to be submitted without this flag.
Reported-by: Joe Rayhawk <jrayhawk@fairlystable.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60af3d037e upstream.
We've got strange errors in get_ctl_value() in mixer.c during
probing, e.g. on Hercules RMX2 DJ Controller:
ALSA mixer.c:352 cannot get ctl value: req = 0x83, wValue = 0x201, wIndex = 0xa00, type = 4
ALSA mixer.c:352 cannot get ctl value: req = 0x83, wValue = 0x200, wIndex = 0xa00, type = 4
....
It turned out that the culprit is autopm: snd_usb_autoresume() returns
-ENODEV when called during card->probing = 1.
Since the call itself during card->probing = 1 is valid, let's fix the
return value of snd_usb_autoresume() as success.
Reported-and-tested-by: Daniel Schürmann <daschuer@mixxx.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbc200bca4 upstream.
Commit 88a8516a21 (ALSA: usbaudio: implement USB autosuspend)
introduced autopm for all USB audio/MIDI devices. However, many MIDI
devices, such as synthesizers, do not merely transmit MIDI messages but
use their MIDI inputs to control other functions. With autopm, these
devices would get powered down as soon as the last MIDI port device is
closed on the host.
Even some plain MIDI interfaces could get broken: they automatically
send Active Sensing messages while powered up, but as soon as these
messages cease, the receiving device would interpret this as an
accidental disconnection.
Commit f5f165418c (ALSA: usb-audio: Fix missing autopm for MIDI input)
introduced another regression: some devices (e.g. the Roland GAIA SH-01)
are self-powered but do a reset whenever the USB interface's power state
changes.
To work around all this, just disable autopm for all USB MIDI devices.
Reported-by: Laurens Holst
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1539d4f82a upstream.
When recording at 176.2KHz or 192Khz, the device adds a 32-bit length
header to the capture packets, which obviously needs to be ignored for
recording to work properly.
Userspace expected: L0 L1 L2 R0 R1 R2
...but actually got: R2 L0 L1 L2 R0 R1
Also, the last byte of the length header being interpreted as L0 of
the first sample caused spikes every 0.5ms, resulting in a loud 16KHz
tone (about the highest 'B' on a piano) being present throughout
captures.
Tested at all sample rates on an E-Mu 0404USB, and tested for
regressions on a generic USB headset.
Signed-off-by: Calvin Owens <jcalvinowens@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebfc594c02 upstream.
The USB_DT_CS_ENDPOINT class-specific endpoint descriptor is usually
stuffed directly after the standard USB endpoint descriptor, and this is
where the driver currently expects it to be.
There are, however, devices in the wild that have it the other way
around in their descriptor sets, so the USB_DT_CS_ENDPOINT comes
*before* the standard enpoint. Devices known to implement it that way
are "Sennheiser BTD-500" and Plantronics USB headsets.
When the driver can't find the USB_DT_CS_ENDPOINT, it won't be able to
change sample rates, as the bitmask for the validity of this command is
storen in bmAttributes of that descriptor.
Fix this by searching the entire interface instead of just the extra
bytes of the first endpoint, in case the latter fails.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Torstein Hegge <hegge@resisty.net>
Reported-and-tested-by: Yves G <alsa-user@vivigatt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32d33b29ba upstream.
If the TPM has already been sent a SaveState command before the driver
is loaded it may have problems sending that same command again later.
This issue is seen with the Chromebook Pixel due to a firmware bug in
the legacy mode boot path which is sending the SaveState command
before booting the kernel. More information is available at
http://crbug.com/203524
This change introduces a retry of the SaveState command in the suspend
path in order to work around this issue. A future firmware update
should fix this but this is also a trivial workaround in the driver
that has no effect on systems that do not show this problem.
When this does happen the TPM responds with a non-fatal TPM_RETRY code
that is defined in the specification:
The TPM is too busy to respond to the command immediately, but the
command could be resubmitted at a later time. The TPM MAY return
TPM_RETRY for any command at any time.
It can take several seconds before the TPM will respond again. I
measured a typical time between 3 and 4 seconds and the timeout is set
at a safe 5 seconds.
It is also possible to reproduce this with commands via /dev/tpm0.
The bug linked above has a python script attached which can be used to
test for this problem. I tested a variety of TPMs from Infineon,
Nuvoton, Atmel, and STMicro but was only able to reproduce this with
LPC and I2C TPMs from Infineon.
The TPM specification only loosely defines this behavior:
TPM Main Level 2 Part 3 v1.2 r116, section 3.3. TPM_SaveState:
The TPM MAY declare all preserved values invalid in response to any
command other than TPM_Init.
TCG PC Client BIOS Spec 1.21 section 8.3.1.
After issuing a TPM_SaveState command, the OS SHOULD NOT issue TPM
commands before transitioning to S3 without issuing another
TPM_SaveState command.
TCG PC Client TIS 1.21, section 4. Power Management:
The TPM_SaveState command allows a Static OS to indicate to the TPM
that the platform may enter a low power state where the TPM will be
required to enter into the D3 power state. The use of the term "may"
is significant in that there is no requirement for the platform to
actually enter the low power state after sending the TPM_SaveState
command. The software may, in fact, send subsequent commands after
sending the TPM_SaveState command.
Change-Id: I52b41e826412688e5b6c8ddd3bb16409939704e9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Dirk Hohndel <dirk@hohndel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ee8630e02 upstream.
On architectures where a pgd entry may be shared between user and kernel
(e.g. ARM+LPAE), freeing page tables needs a ceiling other than 0.
This patch introduces a generic USER_PGTABLES_CEILING that arch code can
override. It is the responsibility of the arch code setting the ceiling
to ensure the complete freeing of the page tables (usually in
pgd_free()).
[catalin.marinas@arm.com: commit log; shift_arg_pages(), asm-generic/pgtables.h changes]
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de53e9caa4 upstream.
The Linux Kernel contains some inline assembly source code which has
wrong asm register constraints in arch/ia64/kvm/vtlb.c.
I observed this on Kernel 3.2.35 but it is also true on the most
recent Kernel 3.9-rc1.
File arch/ia64/kvm/vtlb.c:
u64 guest_vhpt_lookup(u64 iha, u64 *pte)
{
u64 ret;
struct thash_data *data;
data = __vtr_lookup(current_vcpu, iha, D_TLB);
if (data != NULL)
thash_vhpt_insert(current_vcpu, data->page_flags,
data->itir, iha, D_TLB);
asm volatile (
"rsm psr.ic|psr.i;;"
"srlz.d;;"
"ld8.s r9=[%1];;"
"tnat.nz p6,p7=r9;;"
"(p6) mov %0=1;"
"(p6) mov r9=r0;"
"(p7) extr.u r9=r9,0,53;;"
"(p7) mov %0=r0;"
"(p7) st8 [%2]=r9;;"
"ssm psr.ic;;"
"srlz.d;;"
"ssm psr.i;;"
"srlz.d;;"
: "=r"(ret) : "r"(iha), "r"(pte):"memory");
return ret;
}
The list of output registers is
: "=r"(ret) : "r"(iha), "r"(pte):"memory");
The constraint "=r" means that the GCC has to maintain that these vars
are in registers and contain valid info when the program flow leaves
the assembly block (output registers).
But "=r" also means that GCC can put them in registers that are used
as input registers. Input registers are iha, pte on the example.
If the predicate p7 is true, the 8th assembly instruction
"(p7) mov %0=r0;"
is the first one which writes to a register which is maintained by the
register constraints; it sets %0. %0 means the first register operand;
it is ret here.
This instruction might overwrite the %2 register (pte) which is needed
by the next instruction:
"(p7) st8 [%2]=r9;;"
Whether it really happens depends on how GCC decides what registers it
uses and how it optimizes the code.
The attached patch fixes the register operand constraints in
arch/ia64/kvm/vtlb.c.
The register constraints should be
: "=&r"(ret) : "r"(iha), "r"(pte):"memory");
The & means that GCC must not use any of the input registers to place
this output register in.
This is Debian bug#702639
(http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=702639).
The patch is applicable on Kernel 3.9-rc1, 3.2.35 and many other versions.
Signed-off-by: Stephan Schreiber <info@fs-driver.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e9dafd873 upstream.
Some cards on Ralink RT30xx chipset not have correctly TX_MIXER_GAIN
value in them EEPROM/EFUSE. In this case, we must use default value,
but always used EEPROM/EFUSE value. As result we have tranmitt power
range from -10dBm to +6dBm instead 0dBm to +16dBm.
Correctly value in EEPROM/EFUSE is one or more for RT3070 and two or
more for other RT30xx chips.
Tested on Canyon CNP-WF518N1 usb Wi-Fi dongle and Jorjin WN8020 usb
embedded Wi-Fi module.
Signed-off-by: Alex A. Mihaylov <minimumlaw@rambler.ru>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 769ba7212f upstream.
Commit b51306c (PCI: Set device power state to PCI_D0 for device
without native PM support) modified pci_platform_power_transition()
by adding code causing dev->current_state for devices that don't
support native PCI PM but are power-manageable by the platform to be
changed to PCI_D0 regardless of the value returned by the preceding
platform_pci_set_power_state(). In particular, that also is done
if the platform_pci_set_power_state() has been successful, which
causes the correct power state of the device set by
pci_update_current_state() in that case to be overwritten by PCI_D0.
Fix that mistake by making the fallback to PCI_D0 only happen if
the platform_pci_set_power_state() has returned an error.
[bhelgaas: folded in Yinghai's simplification, added URL & stable info]
Reference: http://lkml.kernel.org/r/27806FC4E5928A408B78E88BBC67A2306F466BBA@ORSMSX101.amr.corp.intel.com
Reported-by: Chris J. Benenati <chris.j.benenati@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 545d6e189a upstream.
Found problem on system that firmware that could handle pci aer.
Firmware get error reporting after pci injecting error, before os boots.
But after os boots, firmware can not get report anymore, even pci=noaer
is passed.
Root cause: BIOS _OSC has problem with query bit checking.
It turns out that BIOS vendor is copying example code from ACPI Spec.
In ACPI Spec 5.0, page 290:
If (Not(And(CDW1,1))) // Query flag clear?
{ // Disable GPEs for features granted native control.
If (And(CTRL,0x01)) // Hot plug control granted?
{
Store(0,HPCE) // clear the hot plug SCI enable bit
Store(1,HPCS) // clear the hot plug SCI status bit
}
...
}
When Query flag is set, And(CDW1,1) will be 1, Not(1) will return 0xfffffffe.
So it will get into code path that should be for control set only.
BIOS acpi code should be changed to "If (LEqual(And(CDW1,1), 0)))"
Current kernel code is using _OSC query to notify firmware about support
from OS and then use _OSC to set control bits.
During query support, current code is using all possible controls.
So will execute code that should be only for control set stage.
That will have problem when pci=noaer or aer firmware_first is used.
As firmware have that control set for os aer already in query support stage,
but later will not os aer handling.
We should avoid passing all possible controls, just use osc_control_set
instead.
That should workaround BIOS bugs with affected systems on the field
as more bios vendors are copying sample code from ACPI spec.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d303e9e98f upstream.
Back 2010 during a revamp of the irq code some initializations
were moved from ia64_mca_init() to ia64_mca_late_init() in
commit c75f2aa13f
Cannot use register_percpu_irq() from ia64_mca_init()
But this was hideously wrong. First of all these initializations
are now down far too late. Specifically after all the other cpus
have been brought up and initialized their own CMC vectors from
smp_callin(). Also ia64_mca_late_init() may be called from any cpu
so the line:
ia64_mca_cmc_vector_setup(); /* Setup vector on BSP */
is generally not executed on the BSP, and so the CMC vector isn't
setup at all on that processor.
Make use of the arch_early_irq_init() hook to get this code executed
at just the right moment: not too early, not too late.
Reported-by: Fred Hartnett <fred.hartnett@hp.com>
Tested-by: Fred Hartnett <fred.hartnett@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7db5e7660 upstream.
The inode->i_mutex isn't hold when updating filp->f_pos
in read()/write(), so the filp->f_pos might be read as
0 or 1 in readdir() when there is concurrent read()/write()
on this same file, then may cause use after free in readdir().
The bug can be reproduced with Li Zefan's test code on the
link:
https://patchwork.kernel.org/patch/2160771/
This patch fixes the use after free under this situation.
Reported-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 288fa3e022 upstream.
As part of updating the vmbus protocol, the function hv_need_to_signal()
was introduced. This functions helps optimize signalling from guest to
host. The newly added memory barrier is needed to ensure that we correctly
decide when to signal the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reported-by: Olaf Hering <olh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57ae1b0532 upstream.
Occurs when CONFIG_CRYPTO_CRC32C_INTEL=y and CONFIG_CRYPTO_CRC32C_INTEL=y.
Older versions of bintuils do not support the pclmulqdq instruction. The
PCLMULQDQ gas macro is used instead.
Signed-off-by: Sandy Wu <sandyw@twitter.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c39e8e4354 upstream.
The TX_FIFO register is 10 bits wide. The lower 8 bits are the data to be
written, while the upper two bits are flags to indicate stop/start.
The driver apparently attempted to optimize write access, by only writing a
byte in those cases where the stop/start bits are zero. However, we have
seen cases where the lower byte is duplicated onto the upper byte by the
hardware, which causes inadvertent stop/starts.
This patch changes the write access to the transmit FIFO to always be 16 bits
wide.
Signed off by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4df297129f upstream.
Currently, the depth reported in the stack tracer stack_trace file
does not match the stack_max_size file. This is because the stack_max_size
includes the overhead of stack tracer itself while the depth does not.
The first time a max is triggered, a calculation is not performed that
figures out the overhead of the stack tracer and subtracts it from
the stack_max_size variable. The overhead is stored and is subtracted
from the reported stack size for comparing for a new max.
Now the stack_max_size corresponds to the reported depth:
# cat stack_max_size
4640
# cat stack_trace
Depth Size Location (48 entries)
----- ---- --------
0) 4640 32 _raw_spin_lock+0x18/0x24
1) 4608 112 ____cache_alloc+0xb7/0x22d
2) 4496 80 kmem_cache_alloc+0x63/0x12f
3) 4416 16 mempool_alloc_slab+0x15/0x17
[...]
While testing against and older gcc on x86 that uses mcount instead
of fentry, I found that pasing in ip + MCOUNT_INSN_SIZE let the
stack trace show one more function deep which was missing before.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4ecbfc49b upstream.
When gcc 4.6 on x86 is used, the function tracer will use the new
option -mfentry which does a call to "fentry" at every function
instead of "mcount". The significance of this is that fentry is
called as the first operation of the function instead of the mcount
usage of being called after the stack.
This causes the stack tracer to show some bogus results for the size
of the last function traced, as well as showing "ftrace_call" instead
of the function. This is due to the stack frame not being set up
by the function that is about to be traced.
# cat stack_trace
Depth Size Location (48 entries)
----- ---- --------
0) 4824 216 ftrace_call+0x5/0x2f
1) 4608 112 ____cache_alloc+0xb7/0x22d
2) 4496 80 kmem_cache_alloc+0x63/0x12f
The 216 size for ftrace_call includes both the ftrace_call stack
(which includes the saving of registers it does), as well as the
stack size of the parent.
To fix this, if CC_USING_FENTRY is defined, then the stack_tracer
will reserve the first item in stack_dump_trace[] array when
calling save_stack_trace(), and it will fill it in with the parent ip.
Then the code will look for the parent pointer on the stack and
give the real size of the parent's stack pointer:
# cat stack_trace
Depth Size Location (14 entries)
----- ---- --------
0) 2640 48 update_group_power+0x26/0x187
1) 2592 224 update_sd_lb_stats+0x2a5/0x4ac
2) 2368 160 find_busiest_group+0x31/0x1f1
3) 2208 256 load_balance+0xd9/0x662
I'm Cc'ing stable, although it's not urgent, as it only shows bogus
size for item #0, the rest of the trace is legit. It should still be
corrected in previous stable releases.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87889501d0 upstream.
Use the stack of stack_trace_call() instead of check_stack() as
the test pointer for max stack size. It makes it a bit cleaner
and a little more accurate.
Adding stable, as a later fix depends on this patch.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0b885657b upstream.
We first tried to avoid updating atime/mtime entirely (commit
b0de59b573: "TTY: do not update atime/mtime on read/write"), and then
limited it to only update it occasionally (commit 37b7f3c765: "TTY:
fix atime/mtime regression"), but it turns out that this was both
insufficient and overkill.
It was insufficient because we let people attach to the shared ptmx node
to see activity without even reading atime/mtime, and it was overkill
because the "only once a minute" means that you can't really tell an
idle person from an active one with 'w'.
So this tries to fix the problem properly. It marks the shared ptmx
node as un-notifiable, and it lowers the "only once a minute" to a few
seconds instead - still long enough that you can't time individual
keystrokes, but short enough that you can tell whether somebody is
active or not.
Reported-by: Simon Kirby <sim@hostway.ca>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd4baaaa04 upstream.
An early draft of the PHC patch series included an alarm in the
gianfar driver. During the review process, the alarm code was dropped,
but the capability removal was overlooked. This patch fixes the issue
by advertising zero alarms.
This patch should be applied to every 3.x stable kernel.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Chris LaRocque <clarocq@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 104ad3b32d upstream.
ARM processors with LPAE enabled use 3 levels of page tables, with an
entry in the top level (pgd) covering 1GB of virtual space. Because of
the branch relocation limitations on ARM, the loadable modules are
mapped 16MB below PAGE_OFFSET, making the corresponding 1GB pgd shared
between kernel modules and user space.
If free_pgtables() is called with the default ceiling 0,
free_pgd_range() (and subsequently called functions) also frees the page
table shared between user space and kernel modules (which is normally
handled by the ARM-specific pgd_free() function). This patch changes
defines the ARM USER_PGTABLES_CEILING to TASK_SIZE when CONFIG_ARM_LPAE
is enabled.
Note that the pgd_free() function already checks the presence of the
shared pmd page allocated by pgd_alloc() and frees it, though with
ceiling 0 this wasn't necessary.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a65dcc04c upstream.
The serial core uses device_find_child() but does not drop the reference to
the retrieved child after using it. This patch add the missing put_device().
What I have done to test this issue.
I used a machine with an AMBA PL011 serial driver. I tested the patch on
next-20120408 because the last branch [next-20120415] does not boot on this
board.
For test purpose, I added some pr_info() messages to print the refcount
after device_find_child() (lines: 1937,2009), and after put_device()
(lines: 1947, 2021).
Boot the machine *without* put_device(). Then:
echo reboot > /sys/power/disk
echo disk > /sys/power/state
[ 87.058575] uart_suspend_port:1937 refcount 4
[ 87.058582] uart_suspend_port:1947 refcount 4
[ 87.098083] uart_resume_port:2009refcount 5
[ 87.098088] uart_resume_port:2021 refcount 5
echo disk > /sys/power/state
[ 103.055574] uart_suspend_port:1937 refcount 6
[ 103.055580] uart_suspend_port:1947 refcount 6
[ 103.095322] uart_resume_port:2009 refcount 7
[ 103.095327] uart_resume_port:2021 refcount 7
echo disk > /sys/power/state
[ 252.459580] uart_suspend_port:1937 refcount 8
[ 252.459586] uart_suspend_port:1947 refcount 8
[ 252.499611] uart_resume_port:2009 refcount 9
[ 252.499616] uart_resume_port:2021 refcount 9
The refcount continuously increased.
Boot the machine *with* this patch. Then:
echo reboot > /sys/power/disk
echo disk > /sys/power/state
[ 159.333559] uart_suspend_port:1937 refcount 4
[ 159.333566] uart_suspend_port:1947 refcount 3
[ 159.372751] uart_resume_port:2009 refcount 4
[ 159.372755] uart_resume_port:2021 refcount 3
echo disk > /sys/power/state
[ 185.713614] uart_suspend_port:1937 refcount 4
[ 185.713621] uart_suspend_port:1947 refcount 3
[ 185.752935] uart_resume_port:2009 refcount 4
[ 185.752940] uart_resume_port:2021 refcount 3
echo disk > /sys/power/state
[ 207.458584] uart_suspend_port:1937 refcount 4
[ 207.458591] uart_suspend_port:1947 refcount 3
[ 207.498598] uart_resume_port:2009 refcount 4
[ 207.498605] uart_resume_port:2021 refcount 3
The refcount correctly handled.
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66ff0fe9e7 upstream.
While we don't use the spinlock interrupt line (see for details
commit f10cd522c5 -
xen: disable PV spinlocks on HVM) - we should still do the proper
init / deinit sequence. We did not do that correctly and for the
CPU init for PVHVM guest we would allocate an interrupt line - but
failed to deallocate the old interrupt line.
This resulted in leakage of an irq_desc but more importantly this splat
as we online an offlined CPU:
genirq: Flags mismatch irq 71. 0002cc20 (spinlock1) vs. 0002cc20 (spinlock1)
Pid: 2542, comm: init.late Not tainted 3.9.0-rc6upstream #1
Call Trace:
[<ffffffff811156de>] __setup_irq+0x23e/0x4a0
[<ffffffff81194191>] ? kmem_cache_alloc_trace+0x221/0x250
[<ffffffff811161bb>] request_threaded_irq+0xfb/0x160
[<ffffffff8104c6f0>] ? xen_spin_trylock+0x20/0x20
[<ffffffff813a8423>] bind_ipi_to_irqhandler+0xa3/0x160
[<ffffffff81303758>] ? kasprintf+0x38/0x40
[<ffffffff8104c6f0>] ? xen_spin_trylock+0x20/0x20
[<ffffffff810cad35>] ? update_max_interval+0x15/0x40
[<ffffffff816605db>] xen_init_lock_cpu+0x3c/0x78
[<ffffffff81660029>] xen_hvm_cpu_notify+0x29/0x33
[<ffffffff81676bdd>] notifier_call_chain+0x4d/0x70
[<ffffffff810bb2a9>] __raw_notifier_call_chain+0x9/0x10
[<ffffffff8109402b>] __cpu_notify+0x1b/0x30
[<ffffffff8166834a>] _cpu_up+0xa0/0x14b
[<ffffffff816684ce>] cpu_up+0xd9/0xec
[<ffffffff8165f754>] store_online+0x94/0xd0
[<ffffffff8141d15b>] dev_attr_store+0x1b/0x20
[<ffffffff81218f44>] sysfs_write_file+0xf4/0x170
[<ffffffff811a2864>] vfs_write+0xb4/0x130
[<ffffffff811a302a>] sys_write+0x5a/0xa0
[<ffffffff8167ada9>] system_call_fastpath+0x16/0x1b
cpu 1 spinlock event irq -16
smpboot: Booting Node 0 Processor 1 APIC 0x2
And if one looks at the /proc/interrupts right after
offlining (CPU1):
70: 0 0 xen-percpu-ipi spinlock0
71: 0 0 xen-percpu-ipi spinlock1
77: 0 0 xen-percpu-ipi spinlock2
There is the oddity of the 'spinlock1' still being present.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 888b65b4bc upstream.
In the PVHVM path when we do CPU online/offline path we would
leak the timer%d IRQ line everytime we do a offline event. The
online path (xen_hvm_setup_cpu_clockevents via
x86_cpuinit.setup_percpu_clockev) would allocate a new interrupt
line for the timer%d.
But we would still use the old interrupt line leading to:
kernel BUG at /home/konrad/ssd/konrad/linux/kernel/hrtimer.c:1261!
invalid opcode: 0000 [#1] SMP
RIP: 0010:[<ffffffff810b9e21>] [<ffffffff810b9e21>] hrtimer_interrupt+0x261/0x270
.. snip..
<IRQ>
[<ffffffff810445ef>] xen_timer_interrupt+0x2f/0x1b0
[<ffffffff81104825>] ? stop_machine_cpu_stop+0xb5/0xf0
[<ffffffff8111434c>] handle_irq_event_percpu+0x7c/0x240
[<ffffffff811175b9>] handle_percpu_irq+0x49/0x70
[<ffffffff813a74a3>] __xen_evtchn_do_upcall+0x1c3/0x2f0
[<ffffffff813a760a>] xen_evtchn_do_upcall+0x2a/0x40
[<ffffffff8167c26d>] xen_hvm_callback_vector+0x6d/0x80
<EOI>
[<ffffffff81666d01>] ? start_secondary+0x193/0x1a8
[<ffffffff81666cfd>] ? start_secondary+0x18f/0x1a8
There is also the oddity (timer1) in the /proc/interrupts after
offlining CPU1:
64: 1121 0 xen-percpu-virq timer0
78: 0 0 xen-percpu-virq timer1
84: 0 2483 xen-percpu-virq timer2
This patch fixes it.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7918c92ae9 upstream.
When we online the CPU, we get this splat:
smpboot: Booting Node 0 Processor 1 APIC 0x2
installing Xen timer for CPU 1
BUG: sleeping function called from invalid context at /home/konrad/ssd/konrad/linux/mm/slab.c:3179
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/1
Pid: 0, comm: swapper/1 Not tainted 3.9.0-rc6upstream-00001-g3884fad #1
Call Trace:
[<ffffffff810c1fea>] __might_sleep+0xda/0x100
[<ffffffff81194617>] __kmalloc_track_caller+0x1e7/0x2c0
[<ffffffff81303758>] ? kasprintf+0x38/0x40
[<ffffffff813036eb>] kvasprintf+0x5b/0x90
[<ffffffff81303758>] kasprintf+0x38/0x40
[<ffffffff81044510>] xen_setup_timer+0x30/0xb0
[<ffffffff810445af>] xen_hvm_setup_cpu_clockevents+0x1f/0x30
[<ffffffff81666d0a>] start_secondary+0x19c/0x1a8
The solution to that is use kasprintf in the CPU hotplug path
that 'online's the CPU. That is, do it in in xen_hvm_cpu_notify,
and remove the call to in xen_hvm_setup_cpu_clockevents.
Unfortunatly the later is not a good idea as the bootup path
does not use xen_hvm_cpu_notify so we would end up never allocating
timer%d interrupt lines when booting. As such add the check for
atomic() to continue.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94c163663f upstream.
In case a machine supports memory hotplug all active memory increments
present at IPL time have been initialized with a "usecount" of 1.
This is wrong if the memory increment size is larger than the memory
section size of the memory hotplug code. If that is the case the
usecount must be initialized with the number of memory sections that
fit into one memory increment.
Otherwise it is possible to put a memory increment into standby state
even if there are still active sections.
Afterwards addressing exceptions might happen which cause the kernel
to panic.
However even worse, if a memory increment was put into standby state
and afterwards into active state again, it's contents would have been
zeroed, leading to memory corruption.
This was only an issue for machines that support standby memory and
have at least 256GB memory.
This is broken since commit fdb1bb15 "[S390] sclp/memory hotplug: fix
initial usecount of increments".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 671b4b2ba9 upstream.
Many cards based on CY7C68300A/B/C use the USB ID 04b4:6830 but only the
B and C variants (EZ-USB AT2LP) support the ATA Command Block
functionality, according to the data sheets. The A variant (EZ-USB AT2)
locks up if ATACB is attempted, until a typical 30 seconds timeout runs
out and a USB reset is performed.
https://bugs.launchpad.net/bugs/428469
It seems that one way to spot a CY7C68300A (at least where the card
manufacturer left Cypress' EEPROM default vaules, against Cypress'
recommendations) is to look at the USB string descriptor indices.
A http://media.digikey.com/pdf/Data%20Sheets/Cypress%20PDFs/CY7C68300A.pdf
B http://www.farnell.com/datasheets/43456.pdf
C http://www.cypress.com/?rID=14189
Note that a CY7C68300B/C chip appears as CY7C68300A if it is running
in Backward Compatibility Mode, and if ATACB would be supported in this
case there is anyway no way to tell which chip it really is.
For 5 years my external USB drive has been locking up for half a minute
when plugged in and ata_id is run by udev, or anytime hdparm or similar
is run on it.
Finally looking at the /correct/ datasheet I think I found the reason. I
am aware the quirk in this patch is a bit hacky, but the hardware
manufacturers haven't made it easy for us.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ca2cd291f upstream.
In hardware_enqueue code adds one extra td with dma_pool_alloc if
mReq->req.zero is true. When _ep_nuke will be called for that endpoint,
dma_pool_free will not be called to free that memory again. That patch
fixes this.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9c174302b upstream.
The udc uses an shared dma memory space between hard and software. This
memory layout is described in ci13xxx_qh and ci13xxx_td which are marked
with the attribute ((packed)).
The compiler currently does not know about the alignment of the memory
layout, and will create strb and ldrb operations.
The Datasheet of the synopsys core describes, that some operations on
the mapped memory need to be atomic double word operations. I.e. the
next pointer addressing in the qhead, as otherwise the hardware will
read wrong data and totally stuck.
This is also possible while working with the current active td queue,
and preparing the td->ptr.next in software while the hardware is still
working with the current active td which is supposed to be changed:
writeb(0xde, &td->ptr.next + 0x0); /* strb */
writeb(0xad, &td->ptr.next + 0x1); /* strb */
<----- hardware reads value of td->ptr.next and get stuck!
writeb(0xbe, &td->ptr.next + 0x2); /* strb */
writeb(0xef, &td->ptr.next + 0x3); /* strb */
This appeares on armv5 machines where the hardware does not support
unaligned 32bit operations.
This patch adds the attribute ((aligned(4))) to the structures to tell
the compiler to use 32bit operations. It also adds an wmb() for the
prepared TD data before it gets enqueued into the qhead.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1361bf4b9f upstream.
When usbfs receives a ctrl-request from userspace it calls check_ctrlrecip,
which for a request with USB_RECIP_ENDPOINT tries to map this to an interface
to see if this interface is claimed, except for ctrl-requests with a type of
USB_TYPE_VENDOR.
When trying to use this device: http://www.akaipro.com/eiepro
redirected to a Windows vm running on qemu on top of Linux.
The windows driver makes a ctrl-req with USB_TYPE_CLASS and
USB_RECIP_ENDPOINT with index 0, and the mapping of the endpoint (0) to
the interface fails since ep 0 is the ctrl endpoint and thus never is
part of an interface.
This patch fixes this ctrl-req failing by skipping the checkintf call for
USB_RECIP_ENDPOINT ctrl-reqs on the ctrl endpoint.
Reported-by: Dave Stikkolorum <d.r.stikkolorum@hhs.nl>
Tested-by: Dave Stikkolorum <d.r.stikkolorum@hhs.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6fd35ee57 upstream.
Fix regression introduced by commit f40d78155 ("USB: io_ti: kill custom
closing_wait implementation") which made TIOCGSERIAL return the wrong
value for closing_wait.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71d9a2b95f upstream.
The FT4232H used in the ST Micro Connect Lite has four hi-speed UART ports.
The first two ports are reserved for the JTAG interface.
We enable by default ports 2 and 3 as UARTs (where port 2 is a
conventional RS-232 UART)
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f06d15f8d upstream.
The current ST Micro Connect Lite uses the FT4232H hi-speed quad USB
UART FTDI chip. It is also possible to drive STM reference targets
populated with an on-board JTAG debugger based on the FT2232H chip with
the same STMicroelectronics tools.
For this reason, the ST Micro Connect Lite PIDs should be
ST_STMCLT_2232_PID: 0x3746
ST_STMCLT_4232_PID: 0x3747
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58f8b6c4fa upstream.
This patch add a missing usb device id for the GDMBoost V1.x device
The patch is against 3.9-rc5
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ceb59557b upstream.
The RCU docs used to state that rcu_barrier() included a wait
for an RCU grace period; however the comments for rcu_barrier()
as of commit f0a0e6f... "rcu: Clarify memory-ordering properties
of grace-period primitives" contradict this.
So add back synchronize_{rcu,net}() to where they once were,
but keep the rcu_barrier()s for the call_rcu() callbacks.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b20d34c458 upstream.
Since Stanislaw's patches, when suspending while connected,
cfg80211 will disconnect. This causes the AP station to be
removed, which uses call_rcu() to clean up. Due to needing
process context, this queues a work struct on the mac80211
workqueue. This will warn and fail when already suspended,
which can happen if the rcu call doesn't happen quickly.
To fix this, replace the synchronize_net() which is really
just synchronize_rcu_expedited() with rcu_barrier(), which
unlike synchronize_rcu() waits until RCU callback have run
and thus avoids this issue.
In theory, this can even happen without Stanislaw's change
to disconnect on suspend since userspace might disconnect
just before suspending, though then it's unlikely that the
call_rcu() will be delayed long enough.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63b77bf489 upstream.
When the stations are being restored because of unassoc
RXON, the LQ cmd may not have been initialized because it
is initialized only after association.
Sending zeroed LQ_CMD makes the fw unhappy: it raises
SYSASSERT_2078.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
[move zero_lq and make static const]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6747e83235 upstream.
In commit 85fe402 (fs: do not assign default i_ino in new_inode), the
initialisation of i_ino was removed from new_inode() and pushed down
into the callers. However spufs_new_inode() was not updated.
This exhibits as no files appearing in /spu, because all our dirents
have a zero inode, which readdir() seems to dislike.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c2a381734 upstream.
In __restore_cpu_power8 we determine if we are HV and if not, we return
before setting HV only resources.
Unfortunately we forgot to restore the link register from r11 before
returning.
This will happen on boot and with secondary CPUs not coming online.
This adds the missing link register restore.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e96ca7f00 upstream.
POWER8 allows us to take interrupts with the MMU on. This gives us a
second set of vectors offset at 0x4000.
Unfortunately when coping these vectors we missed checking for MSR HV
for hardware interrupts (0x500). This results in us trying to use
HSRR0/1 when HV=0, rather than SRR0/1 on HW IRQs
The below fixes this to check CPU_FTR_HVMODE when patching the code at
0x4500.
Also we remove the check for CPU_FTR_ARCH_206 since relocation on IRQs
are only available in arch 2.07 and beyond.
Thanks to benh for helping find this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29ce3c5073 upstream.
In __after_prom_start we copy the kernel down to zero in two calls to
copy_and_flush. After the first call (copy from 0 to copy_to_here:)
we jump to the newly copied code soon after.
Unfortunately there's no isync between the copy of this code and the
jump to it. Hence it's possible that stale instructions could still be
in the icache or pipeline before we branch to it.
We've seen this on real machines and it's results in no console output
after:
calling quiesce...
returning from prom_init
The below adds an isync to ensure that the copy and flushing has
completed before any branching to the new instructions occurs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d97558901 upstream.
The TIME_VALID flag is specified for the different states but
the time residency computation is not done, no tk flag, no time
computation in the idle function.
Set the en_core_tk_irqen flag to activate it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d95abbbb29 upstream.
Testing the arm chromebook config against the upstream
kernel produces a linker error for the zsmalloc module from
staging. The symbol flush_tlb_kernel_range is not available
there. Fix this by removing the reimplementation of
unmap_kernel_range in the zsmalloc module and using the
function directly. The unmap_kernel_range function is not
usable by modules, so also disallow building the driver as a
module for now.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
Greg Kroah-Hartman