commit b8612e517c upstream.
Signing a module should only make it trusted by the specific kernel it
was built for, not anything else. If a module signing key is used for
multiple ABI-incompatible kernels, the modules need to include enough
version information to distinguish them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bca014caaa upstream.
Signing a module should only make it trusted by the specific kernel it
was built for, not anything else. Loading a signed module meant for a
kernel with a different ABI could have interesting effects.
Therefore, treat all signatures as invalid when a module is
force-loaded.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99f3c90d0d upstream.
When the corrupt_bio_byte feature was introduced it caused READ bios to
no longer be errored with -EIO during the down_interval. This had to do
with the complexity of needing to submit READs if the corrupt_bio_byte
feature was used.
Fix it so READ bios are properly errored with -EIO; doing so early in
flakey_map() as long as there isn't a match for the corrupt_bio_byte
feature.
Fixes: a3998799fb ("dm flakey: add corrupt_bio_byte feature")
Reported-by: Akira Hayakawa <ruby.wktk@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70c96dfac0 upstream.
As per code flow s3c_rtc_setfreq() will get called with rtc clock disabled
and in set_freq we perform h/w registers read/write, which results in a
kernel crash on exynos7 platform while probing rtc driver.
Below is code flow:
s3c_rtc_probe()
clk_prepare_enable(info->rtc_clk) // rtc clock enabled
s3c_rtc_gettime() // will enable clk if not done, and disable it upon exit
s3c_rtc_setfreq() //then this will be called with clk disabled
This patch take cares of such issue by adding s3c_rtc_{enable/disable}_clk in
s3c_rtc_setfreq().
Fixes: 24e1455493 ("drivers/rtc/rtc-s3c.c: delete duplicate clock control")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1191bd4f6 upstream.
A regression is caused by the following commit:
Commit: 02b771b64b
Subject: ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations
In this commit, using system workqueue causes that the maximum parallel
executions of _Qxx can exceed 255. This violates the method reentrancy
limit in ACPICA and generates the following error log:
ACPI Error: Method reached maximum reentrancy limit (255) (20150818/dsmethod-341)
This patch creates a seperate workqueue and limits the number of parallel
_Qxx evaluations down to a configurable value (can be tuned against number
of online CPUs).
Since EC events are handled after driver probe, we can create the workqueue
in acpi_ec_init().
Fixes: 02b771b64b (ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=135691
Reported-and-tested-by: Helen Buus <ubuntu@hbuus.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb27570525 upstream.
On Intel Merrifield platform several PCI devices have a bogus configuration,
i.e. the IRQ0 had been assigned to few of them. These are PCI root bridge,
eMMC0, HS UART common registers, PWM, and HDMI. The actual interrupt line can
be allocated to one device exclusively, in our case to eMMC0, the rest should
cope without it and basically known drivers for them are not using interrupt
line at all.
Rework IRQ0 workaround, which was previously done to avoid conflict between
eMMC0 and HS UART common registers, to behave differently based on the device
in question, i.e. allocate interrupt line to eMMC0, but silently skip interrupt
allocation for the rest except HS UART common registers which are not used
anyway. With this rework IOSF MBI driver in particular would be used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: 39d9b77b8d ("x86/pci/intel_mid_pci: Work around for IRQ0 assignment")
Link: http://lkml.kernel.org/r/1465842481-136852-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ac0108c2b upstream.
Similar to the AR93xx series, the AR94xx and the Qualcomm QCA988x also have
the same quirk for the Bus Reset.
Fixes: c3e59ee4e7 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ef0665398 upstream.
At first, we prefer to use mips clockevent device, so we decrease the
rating of hpet clockevent device.
For hpet, if HPET_MIN_PROG_DELTA (minimum delta of hpet programming) is
too small and HPET_MIN_CYCLES (threshold of -ETIME checking) is too
large, then hpet_next_event() can easily return -ETIME. After commit
c6eb3f70d4 ("hrtimer: Get rid of hrtimer softirq") this will cause
a RCU stall.
So, HPET_MIN_PROG_DELTA must be sufficient that we don't re-trip the
-ETIME check -- if we do, we will return -ETIME, forward the next event
time, try to set it, return -ETIME again, and basically lock the system
up. Meanwhile, HPET_MIN_CYCLES doesn't need to be too large, 16 cycles
is enough.
This solution is similar to commit f9eccf2461 ("clocksource/drivers
/vt8500: Increase the minimum delta").
By the way, this patch ensures hpet count/compare to be 32-bit long.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@imgtec.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13819/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db1bb44c4c upstream.
We're always tracing IPv4 or IPv6 addresses, so we can save a lot
of space on the ringbuffer by allocating the correct sockaddr size.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Fixes: 83a712e0af "sunrpc: add some tracepoints around ..."
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2de4fcc646 upstream.
Some ASUS laptops were shipped with touchpads that require to be woken up
first, before trying to switch them into absolute reporting mode, otherwise
touchpad would fail to work while flooding the logs with:
elan_i2c i2c-ELAN1000:00: invalid report id data (1)
Among affected devices are Asus E202SA, N552VW, X456UF, UX305CA, and
others. We detect such devices by checking the IC type and product ID
numbers and adjusting order of operations accordingly.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Reported-by: Chris Chiu <chiu@endlessm.com>
Reported-by: Vlad Glagolev <stealth@vaygr.net>
Tested-by: Vlad Glagolev <stealth@vaygr.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57a05d83b1 upstream.
We are in atomic context and must not sleep.
Sleeping here is possible since malloc() maps
to kmalloc() with GFP_KERNEL.
Fixes: b6024b21 ("um: extend fpstate to _xstate to support YMM registers")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 410c29dfbf upstream.
If a Simple command is sent with a failure, target_setup_cmd_from_cdb
returns with TCM_UNSUPPORTED_SCSI_OPCODE or TCM_INVALID_CDB_FIELD.
So in the cases where target_setup_cmd_from_cdb returns an error, we
never get far enough to call target_execute_cmd to increment simple_cmds.
Since simple_cmds isn't incremented, the result of the failure from
target_setup_cmd_from_cdb causes transport_generic_request_failure to
decrement simple_cmds, due to call to transport_complete_task_attr.
With this dev->simple_cmds or dev->dev_ordered_sync is now -1, not 0.
So when a subsequent command with an Ordered Task is sent, it causes
a hang, since dev->simple_cmds is at -1.
Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea263c7fad upstream.
max_discard_sectors only 32bits, and some non scsi backend
devices will set this to the max 0xffffffff, so we can end up
overflowing during the max_unmap_lba_count calculation.
This fixes a regression caused by my patch:
commit 8a9ebe717a
Author: Mike Christie <mchristi@redhat.com>
Date: Mon Jan 18 14:09:27 2016 -0600
target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors
which can result in extra discards being sent to due the overflow
causing max_unmap_lba_count to be smaller than what the backing
device can actually support.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 064cdd2d91 upstream.
This patch fixes a race in iscsit_release_commands_from_conn() ->
iscsit_free_cmd() -> transport_generic_free_cmd() + wait_for_tasks=1,
where CMD_T_FABRIC_STOP could end up being set after the final
kref_put() is called from core_tmr_abort_task() context.
This results in transport_generic_free_cmd() blocking indefinately
on se_cmd->cmd_wait_comp, because the target_release_cmd_kref()
check for CMD_T_FABRIC_STOP returns false.
To address this bug, make iscsit_release_commands_from_conn()
do list_splice and set CMD_T_FABRIC_STOP early while holding
iscsi_conn->cmd_lock. Also make iscsit_aborted_task() only
remove iscsi_cmd_t if CMD_T_FABRIC_STOP has not already been
set.
Finally in target_release_cmd_kref(), only honor fabric_stop
if CMD_T_ABORTED has been set.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Tested-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e2c956b8a upstream.
During transport_generic_free_cmd() with a concurrent TMR
ABORT_TASK and shutdown CMD_T_FABRIC_STOP bit set, the
caller will be blocked on se_cmd->cmd_wait_stop completion
until the final kref_put() -> target_release_cmd_kref()
has been invoked to call complete().
However, when ABORT_TASK is completed with FUNCTION_COMPLETE
in core_tmr_abort_task(), the aborted se_cmd will have already
been removed from se_sess->sess_cmd_list via list_del_init().
This results in target_release_cmd_kref() hitting the
legacy list_empty() == true check, invoking ->release_cmd()
but skipping complete() to wakeup se_cmd->cmd_wait_stop
blocked earlier in transport_generic_free_cmd() code.
To address this bug, it's safe to go ahead and drop the
original list_empty() check so that fabric_stop invokes
the complete() as expected, since list_del_init() can
safely be used on a empty list.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Tested-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dff0ca9ea7 upstream.
If a command with a Simple task attribute is failed due to a Unit
Attention, then a subsequent command with an Ordered task attribute
will hang forever. The reason for this is that the Unit Attention
status is checked for in target_setup_cmd_from_cdb, before the call
to target_execute_cmd, which calls target_handle_task_attr, which
in turn increments dev->simple_cmds.
However, transport_generic_request_failure still calls
transport_complete_task_attr, which will decrement dev->simple_cmds.
In this case, simple_cmds is now -1. So when a command with the
Ordered task attribute is sent, target_handle_task_attr sees that
dev->simple_cmds is not 0, so it decides it can't execute the
command until all the (nonexistent) Simple commands have completed.
Reported-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Tested-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Reported-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8abc718de6 upstream.
In MC/S scenario, the conn->sess has been set NULL in
iscsi_login_non_zero_tsih_s1 when the second connection comes here,
then kernel panic.
The conn->sess will be assigned in iscsi_login_non_zero_tsih_s2. So
we should check whether it's NULL before calling.
Signed-off-by: Feng Li <lifeng1519@gmail.com>
Tested-by: Sumit Rai <sumit.rai@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 714fb87e8b upstream.
Install the UBI device object before we arm sysfs.
Otherwise udev tries to read sysfs attributes before UBI is ready and
udev rules will not match.
Signed-off-by: Iosif Harutyunov <iharutyunov@sonicwall.com>
[rw: massaged commit message]
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc743f34df upstream.
We cannot use ubi_* logging functions before the UBI
object is initialized.
Fixes: 3260870331 ("UBI: Extend UBI layer debug/messaging capabilities")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4946784bd3 upstream.
When the volume resize operation shrinks a volume,
LEBs will be unmapped. Since unmapping will not erase these
LEBs immediately we have to wait for that operation to finish.
Otherwise in case of a power cut right after writing the new
volume table the UBI attach process can find more LEBs than the
volume table knows. This will render the UBI image unattachable.
Fix this issue by waiting for erase to complete and write the new
volume table afterward.
Reported-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9fc880723 upstream.
Fix a memory leak resulting from memory allocation in safe_name().
This patch fixes all call sites of safe_name().
Mathieu Malaterre reported the memory leak on boot:
On my PowerMac device-tree would generate a duplicate name:
[ 0.023043] device-tree: Duplicate name in PowerPC,G4@0, renamed to "l2-cache#1"
in this case a newly allocated name is generated by `safe_name`. However
in this case it is never deallocated.
The bug was found using kmemleak reported as:
unreferenced object 0xdf532e60 (size 32):
comm "swapper", pid 1, jiffies 4294892300 (age 1993.532s)
hex dump (first 32 bytes):
6c 32 2d 63 61 63 68 65 23 31 00 dd e4 dd 1e c2 l2-cache#1......
ec d4 ba ce 04 ec cc de 8e 85 e9 ca c4 ec cc 9e ................
backtrace:
[<c02d3350>] kvasprintf+0x64/0xc8
[<c02d3400>] kasprintf+0x4c/0x5c
[<c0453814>] safe_name.isra.1+0x80/0xc4
[<c04545d8>] __of_attach_node_sysfs+0x6c/0x11c
[<c075f21c>] of_core_init+0x8c/0xf8
[<c0729594>] kernel_init_freeable+0xd4/0x208
[<c00047e8>] kernel_init+0x24/0x11c
[<c00158ec>] ret_from_kernel_thread+0x5c/0x64
Link: https://bugzilla.kernel.org/show_bug.cgi?id=120331
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Reported-by: mathieu.malaterre@gmail.com
Tested-by: Mathieu Malaterre <mathieu.malaterre@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0ffeb537f upstream.
Number of outstanding_pi may overflow and as a result may indicate that
there are no elements in the queue. The effect of doing this is that the
MAD layer will get stuck waiting for completions. The MAD layer will
think that the QP is full - because it didn't receive these completions.
This fix changes it so the outstanding_pi number is increased
with 32-bit wraparound and is not limited to max_send_wr so
that the difference between outstanding_pi and outstanding_ci will
really indicate the number of outstanding completions.
Fixes: ea6dc20362 ('IB/mlx5: Reorder GSI completions')
Signed-off-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59ec4b57bc upstream.
One of the machines has ALC255 on it, another one has ALC298 on it.
On the machine with the codec ALC298, it also has the speaker volume
problem, so we add the fixup chained to ALC298_FIXUP_SPK_VOLUME rather
than adding a group of pin definition in the pin quirk table, since
the speak volume problem does not happen on other machines yet.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd9aa335c8 upstream.
We have a Dell AIO on which we can't adjust its speaker's volume.
The problem is it is connected to a Audio Output node without Amp-out
capability. To fix it, we change it to be connnected to a node with
Amp-out capability.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33baefe5e7 upstream.
krealloc() doesn't work always properly with __GFP_ZERO flag as
expected. For clearing the reallocated area, we need to clear
explicitly instead.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 144f4c9839 upstream.
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write,
although it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating endlessly.
The bug may not be easy to reproduce in Linux since user space tools
usually force the padding or round-up the write size to a page-size
multiple.
This was discovered in U-Boot where the issue can be reproduced by
writing any size that is 1 byte less than a page-size multiple.
For example, on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
[Editor's note: the bug was added in commit 29072b9607, but moved
around in commit 66507c7bc8 ("mtd: nand: Add support to use nand_base
poi databuf as bounce buffer")]
Fixes: 29072b9607 ("[MTD] NAND: add subpage write support")
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff06db1efb upstream.
Commit 09954bad4 ("floppy: refactor open() flags handling"), as a
side-effect, causes open(/dev/fdX, O_ACCMODE) to fail. It turns out that
this is being used setfdprm userspace for ioctl-only open().
Reintroduce back the original behavior wrt !(FMODE_READ|FMODE_WRITE)
modes, while still keeping the original O_NDELAY bug fixed.
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df08c32ce3 upstream.
The name for a bdi of a gendisk is derived from the gendisk's devt.
However, since the gendisk is destroyed before the bdi it leaves a
window where a new gendisk could dynamically reuse the same devt while a
bdi with the same name is still live. Arrange for the bdi to hold a
reference against its "owner" disk device while it is registered.
Otherwise we can hit sysfs duplicate name collisions like the following:
WARNING: CPU: 10 PID: 2078 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x64/0x80
sysfs: cannot create duplicate filename '/devices/virtual/bdi/259:1'
Hardware name: HP ProLiant DL580 Gen8, BIOS P79 05/06/2015
0000000000000286 0000000002c04ad5 ffff88006f24f970 ffffffff8134caec
ffff88006f24f9c0 0000000000000000 ffff88006f24f9b0 ffffffff8108c351
0000001f0000000c ffff88105d236000 ffff88105d1031e0 ffff8800357427f8
Call Trace:
[<ffffffff8134caec>] dump_stack+0x63/0x87
[<ffffffff8108c351>] __warn+0xd1/0xf0
[<ffffffff8108c3cf>] warn_slowpath_fmt+0x5f/0x80
[<ffffffff812a0d34>] sysfs_warn_dup+0x64/0x80
[<ffffffff812a0e1e>] sysfs_create_dir_ns+0x7e/0x90
[<ffffffff8134faaa>] kobject_add_internal+0xaa/0x320
[<ffffffff81358d4e>] ? vsnprintf+0x34e/0x4d0
[<ffffffff8134ff55>] kobject_add+0x75/0xd0
[<ffffffff816e66b2>] ? mutex_lock+0x12/0x2f
[<ffffffff8148b0a5>] device_add+0x125/0x610
[<ffffffff8148b788>] device_create_groups_vargs+0xd8/0x100
[<ffffffff8148b7cc>] device_create_vargs+0x1c/0x20
[<ffffffff811b775c>] bdi_register+0x8c/0x180
[<ffffffff811b7877>] bdi_register_dev+0x27/0x30
[<ffffffff813317f5>] add_disk+0x175/0x4a0
Reported-by: Yi Zhang <yizhan@redhat.com>
Tested-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed up missing 0 return in bdi_register_owner().
Signed-off-by: Jens Axboe <axboe@fb.com>
commit 20bd723ec6 upstream.
When a bio is cloned, the newly created bio must be associated with
the same blkcg as the original bio (if BLK_CGROUP is enabled). If
this operation is not performed, then the new bio is not associated
with any group, and the group of the current task is returned when
the group of the bio is requested.
Depending on the cloning frequency, this may cause a large
percentage of the bios belonging to a given group to be treated
as if belonging to other groups (in most cases as if belonging to
the root group). The expected group isolation may thereby be broken.
This commit adds the missing association in bio-cloning functions.
Fixes: da2f0f74cf ("Btrfs: add support for blkio controllers")
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Nikolay Borisov <kernel@kyup.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6154c187b9 upstream.
The LNKGET based atomic sequence in __cmpxchg_u32 has slightly incorrect
constraints for the return value which under certain circumstances can
allow an address unit register to be used as the first operand of a CMP
instruction. This isn't a valid instruction however as the encodings
only allow a data unit to be specified. This would result in an
assembler error like the following:
Error: failed to assemble instruction: "CMP A0.2,D0Ar6"
Fix by changing the constraint from "=&da" (assigned, early clobbered,
data or address unit register) to "=&d" (data unit register only).
The constraint for the second operand, "bd" (an op2 register where op1
is a data unit register and the instruction supports O2R) is already
correct assuming the first operand is a data unit register.
Other cases of CMP in inline asm have had their constraints checked, and
appear to all be fine.
Fixes: 6006c0d8ce ("metag: Atomics, locks and bitops")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2e1c26f0b upstream.
glibc recently did a sync up (94e73c95d9b5 "elf.h: Sync with the gabi
webpage") that added a #define for EM_METAG but did not add relocations
This triggers build errors:
scripts/recordmcount.c: In function 'do_file':
scripts/recordmcount.c:466:28: error: 'R_METAG_ADDR32' undeclared (first use in this function)
case EM_METAG: reltype = R_METAG_ADDR32;
^~~~~~~~~~~~~~
scripts/recordmcount.c:466:28: note: each undeclared identifier is reported only once for each function it appears in
scripts/recordmcount.c:468:20: error: 'R_METAG_NONE' undeclared (first use in this function)
rel_type_nop = R_METAG_NONE;
^~~~~~~~~~~~
Work around this change with some more #ifdefery for the relocations.
Fedora Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1354034
Link: http://lkml.kernel.org/r/1468005530-14757-1-git-send-email-labbott@redhat.com
Cc: James Hogan <james.hogan@imgtec.com>
Fixes: 00512bdd45 ("metag: ftrace support")
Reported-by: Ross Burton <ross.burton@intel.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37cf99e08c upstream.
The balloon has a special mechanism that is subscribed to the oom
notification which leads to deflation for a fixed number of pages.
The number is always fixed even when the balloon is fully deflated.
But leak_balloon did not expect that the pages to deflate will be more
than taken, and raise a "BUG" in balloon_page_dequeue when page list
will be empty.
So, the simplest solution would be to check that the number of releases
pages is less or equal to the number taken pages.
Signed-off-by: Konstantin Neumoin <kneumoin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 196f954e25 upstream.
This reverts commit 013dd9e038
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown")
This commit introduced a regression into stable kernels,
as it reduces output color depth to 6 bpc for any video
sink connected to a Displayport connector if that sink
doesn't report a specific color depth via EDID, or if
our EDID parser doesn't actually recognize the proper
bpc from EDID.
Affected are active DisplayPort->VGA converters and
active DisplayPort->DVI converters. Both should be
able to handle 8 bpc, but are degraded to 6 bpc with
this patch.
The reverted commit was meant to fix
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105331
A followup patch implements a fix for that specific bug,
which is caused by a faulty EDID of the affected DP panel
by adding a new EDID quirk for that panel.
DP 18 bpp fallback handling and other improvements to
DP sink bpc detection will be handled for future
kernels in a separate series of patches.
Please backport to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e10aec652f upstream.
Bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=105331
reports that the "AEO model 0" display is driven with 8 bpc
without dithering by default, which looks bad because that
panel is apparently a 6 bpc DP panel with faulty EDID.
A fix for this was made by commit 013dd9e038
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown").
That commit triggers new regressions in precision for DP->DVI and
DP->VGA displays. A patch is out to revert that commit, but it will
revert video output for the AEO model 0 panel to 8 bpc without
dithering.
The EDID 1.3 of that panel, as decoded from the xrandr output
attached to that bugzilla bug report, is somewhat faulty, and beyond
other problems also sets the "DFP 1.x compliant TMDS" bit, which
according to DFP spec means to drive the panel with 8 bpc and
no dithering in absence of other colorimetry information.
Try to make the original bug reporter happy despite the
faulty EDID by adding a quirk to mark that panel as 6 bpc,
so 6 bpc output with dithering creates a nice picture.
Tested by injecting the edid from the fdo bug into a DP connector
via drm_kms_helper.edid_firmware and verifying the 6 bpc + dithering
is selected.
This patch should be backported to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1f5524a66 upstream.
Restore the correct behaviour (as in check msg.reply) when aux
->transfer() returns 0. It got removed in
commit 82922da391 ("drm/dp_helper: Retry aux transactions on all errors")
Now I can actually dump the "entire" DPCD on a Dell UP2314Q with
ddrescue. It has some offsets in the DPCD that can't be read
for some resaon, all you get is defers. Previously ddrescue would
just give up at the first unredable offset on account of
read() returning 0 means EOF. Here's the ddrescue log
for the interested:
0x00000000 0x00001400 +
0x00001400 0x00000030 -
0x00001430 0x000001D0 +
0x00001600 0x00000030 -
0x00001630 0x0001F9D0 +
0x00021000 0x00000001 -
0x00021001 0x000DEFFF +
Cc: Lyude <cpaul@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch
Fixes: 82922da391 ("drm/dp_helper: Retry aux transactions on all errors")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc0b408f5a upstream.
Because we are using a custom crtc_state structure, we must override the
reset helper to allocate the correct amount of memory.
Fixes: 4e257d9eee ("drm/rockchip: get rid of rockchip_drm_crtc_mode_config")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f1052a8fa upstream.
Update CDCLK_FREQ on BDW after changing the cdclk frequency. Not sure
if this is a late addition to the spec, or if I simply overlooked this
step when writing the original code.
This is what Bspec has to say about CDCLK_FREQ:
"Program this field to the CD clock frequency minus one. This is used to
generate a divided down clock for miscellaneous timers in display."
And the "Broadwell Sequences for Changing CD Clock Frequency" section
clarifies this further:
"For CD clock 337.5 MHz, program 337 decimal.
For CD clock 450 MHz, program 449 decimal.
For CD clock 540 MHz, program 539 decimal.
For CD clock 675 MHz, program 674 decimal."
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: b432e5cfd5 ("drm/i915: BDW clock change support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461689194-6079-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28668f43b8 upstream.
The patch f045f459d9 ("drm/nouveau/fbcon: fix out-of-bounds memory accesses")
tries to fix some out of memory accesses. Unfortunatelly, the patch breaks the
display when using fonts with width that is not divisiable by 8.
The monochrome bitmap for each character is stored in memory by lines from top
to bottom. Each line is padded to a full byte.
For example, for 22x11 font, each line is padded to 16 bits, so each
character is consuming 44 bytes total, that is 11 32-bit words. The patch
f045f459d9 changed the logic to "dsize = ALIGN(image->width *
image->height, 32) >> 5", that is just 8 words - this is incorrect and it
causes display corruption.
This patch adds the necesary padding of lines to 8 bytes.
This patch should be backported to stable kernels where f045f459d9 was
backported.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: f045f459d9 ("drm/nouveau/fbcon: fix out-of-bounds memory accesses")
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14ff8d48f2 upstream.
DRM_CONNECTOR_POLL_CONNECT only enables polling for connections, not
disconnections. Because of this, we end up losing hotplug polling for
analog connectors once they get connected.
Easy way to reproduce:
- Grab a machine with a radeon GPU and a VGA port
- Plug a monitor into the VGA port, wait for it to update the connector
from disconnected to connected
- Disconnect the monitor on VGA, a hotplug event is never sent for the
removal of the connector.
Originally, only using DRM_CONNECTOR_POLL_CONNECT might have been a good
idea since doing VGA polling can sometimes result in having to mess with
the DAC voltages to figure out whether or not there's actually something
there since VGA doesn't have HPD. Doing this would have the potential of
showing visible artifacts on the screen every time we ran a poll while a
VGA display was connected. Luckily, radeon_vga_detect() only resorts to
this sort of polling if the poll is forced, and DRM's polling helper
doesn't force it's polls.
Additionally, this removes some assignments to connector->polled that
weren't actually doing anything.
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8a04c994d upstream.
Some of the checks didn't handle frev 2 tables properly.
amdgpu doesn't support any tables pre-frev 2, so drop
the checks.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23a1a9e54e upstream.
Just about all of amdgpu's connector probing functions try to acquire
runtime PM refs. If we try to do this in the context of
amdgpu_resume_kms by calling drm_helper_hpd_irq_event(), we end up
deadlocking the system.
Since we're guaranteed to be holding the spinlock for RPM in
amdgpu_resume_kms, and we already know the GPU is in working order, we
need to prevent the RPM helpers from trying to run during the initial
connector reprobe on resume.
There's a couple of solutions I've explored for fixing this, but this
one by far seems to be the simplest and most reliable (plus I'm pretty
sure that's what disable_depth is there for anyway).
Reproduction recipe:
- Get any laptop dual GPUs using PRIME
- Make sure runtime PM is enabled for amdgpu
- Boot the machine
- If the machine managed to boot without hanging, switch out of X to
another VT. This should definitely cause X to hang infinitely.
Changes since v1:
- add appropriate #ifdef checks for CONFIG_PM. This is not very
useful, but it appears some kernel test suites test compiling amdgpu
with CONFIG_PM disabled, which results in this patch breaking the builds
if we don't include this #ifdef
Cc: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b636a1b3d6 upstream.
DRM_CONNECTOR_POLL_CONNECT only enables polling for connections, not
disconnections. Because of this, we end up losing hotplug polling for
analog connectors once they get connected.
Easy way to reproduce:
- Grab a machine with an AMD GPU and a VGA port
- Plug a monitor into the VGA port, wait for it to update the connector
from disconnected to connected
- Disconnect the monitor on VGA, a hotplug event is never sent for the
removal of the connector.
Originally, only using DRM_CONNECTOR_POLL_CONNECT might have been a good
idea since doing VGA polling can sometimes result in having to mess with
the DAC voltages to figure out whether or not there's actually something
there since VGA doesn't have HPD. Doing this would have the potential of
showing visible artifacts on the screen every time we ran a poll while a
VGA display was connected. Luckily, amdgpu_vga_detect() only resorts to
this sort of polling if the poll is forced, and DRM's polling helper
doesn't force it's polls.
Additionally, this removes some assignments to connector->polled that
weren't actually doing anything.
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecfaf0c42f upstream.
Commit e93762bbf6 ("w1: masters: omap_hdq: add support for 1-wire
mode") added a statement to clear the hdq_irqstatus flags in
hdq_read_byte().
If the hdq reading process is scheduled slowly or interrupts are
disabled for a while the hardware read activity might already be
finished on entry of hdq_read_byte(). And hdq_isr() already has set the
hdq_irqstatus to 0x6 (can be seen in debug mode) denoting that both, the
TXCOMPLETE and RXCOMPLETE interrupts occurred in parallel.
This means there is no need to wait and the hdq_read_byte() can just
read the byte from the hdq controller.
By resetting hdq_irqstatus to 0 the read process is forced to be always
waiting again (because the if statement always succeeds) but the
hardware will not issue another RXCOMPLETE interrupt. This results in a
false timeout.
After such a situation the hdq bus hangs.
Link: http://lkml.kernel.org/r/b724765f87ad276a69625bc19806c8c8844c4590.1469513669.git.hns@goldelico.com
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e0e367740 upstream.
It seems risky to always rely on the caller to ensure the socket's
address family is correct before passing it to the NetLabel kAPI,
especially since we see at least one LSM which didn't. Add address
family checks to the *_delattr() functions to help prevent future
problems.
Reported-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63af8e44ea upstream.
The valid_entries index should not be incremented until after we have
acquired the pointer to the value, or we will read and write data one
item off.
Fixes: 50e9964141 ("soc: qcom: smp2p: Qualcomm Shared Memory Point to Point")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 726a4994b0 upstream.
Unprivileged users can't use hierarchies if they create them as they do not
have privilieges to the root directory.
Which means the only thing a hiearchy created by an unprivileged user
is good for is expanding the number of cgroup links in every css_set,
which is a DOS attack.
We could allow hierarchies to be created in namespaces in the initial
user namespace. Unfortunately there is only a single namespace for
the names of heirarchies, so that is likely to create more confusion
than not.
So do the simple thing and restrict hiearchy creation to the initial
cgroup namespace.
Fixes: a79a908fd2 ("cgroup: introduce cgroup namespaces")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eedd0f4cbf upstream.
In most code paths involving cgroup migration cgroup_threadgroup_rwsem
is taken. There are two exceptions:
- remove_tasks_in_empty_cpuset calls cgroup_transfer_tasks
- vhost_attach_cgroups_work calls cgroup_attach_task_all
With cgroup_threadgroup_rwsem held it is guaranteed that cgroup_post_fork
and copy_cgroup_ns will reference the same css_set from the process calling
fork.
Without such an interlock there process after fork could reference one
css_set from it's new cgroup namespace and another css_set from
task->cgroups, which semantically is nonsensical.
Fixes: a79a908fd2 ("cgroup: introduce cgroup namespaces")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bd8830875 upstream.
If "clone(CLONE_NEWCGROUP...)" is called it results in a nice lockdep
valid splat.
In __cgroup_proc_write the lock ordering is:
cgroup_mutex -- through cgroup_kn_lock_live
cgroup_threadgroup_rwsem
In copy_process the guts of clone the lock ordering is:
cgroup_threadgroup_rwsem -- through threadgroup_change_begin
cgroup_mutex -- through copy_namespaces -- copy_cgroup_ns
lockdep reports some a different call chains for the first ordering of
cgroup_mutex and cgroup_threadgroup_rwsem but it is harder to trace.
This is most definitely deadlock potential under the right
circumstances.
Fix this by by skipping the cgroup_mutex and making the locking in
copy_cgroup_ns mirror the locking in cgroup_post_fork which also runs
during fork under the cgroup_threadgroup_rwsem.
Fixes: a79a908fd2 ("cgroup: introduce cgroup namespaces")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a376ac11f upstream.
The patch that this was preparing for made it into neither v4.7 nor
v4.8, so we should back this out as well to avoid the opposite
warning:
arch/arm/configs/aspeed_g5_defconfig:62:warning: symbol value '1' invalid for PRINTK_TIME
arch/arm/configs/aspeed_g4_defconfig:61:warning: symbol value '1' invalid for PRINTK_TIME
Sorry for not catching this earlier.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0ef659a300 ("ARM: aspeed: adapt defconfigs for new CONFIG_PRINTK_TIME")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5c86b7496 upstream.
c90bb7b enabled the high speed UARTs of the Jetson TK1. Due to a merge
quirk, wrong addresses were introduced. Fix it and use the correct
addresses.
Thierry let me know, that there is another patch (b5896f67ab in
linux-next) in preparation which removes all the '0,' prefixes of unit
addresses on Tegra124 and is planned to go upstream in 4.8, so
this patch will get reverted then.
But for the moment, this patch is necessary to fix current misbehaviour.
Fixes: c90bb7b9b9 ("ARM: tegra: Add high speed UARTs to Jetson TK1 device tree")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a20303725e upstream.
Clearly QEMU is very permissive in how its PL310 model may be set up,
but the real hardware turns out to be far more particular about things
actually being correct. Fix up the DT description so that the real
thing actually boots:
- The arm,data-latency and arm,tag-latency properties need 3 cells to
be valid, otherwise we end up retaining the default 8-cycle latencies
which leads pretty quickly to lockup.
- The arm,dirty-latency property is only relevant to L210/L220, so get
rid of it.
- The cache geometry override also leads to lockup and/or general
misbehaviour. Irritatingly, the manual doesn't state the actual PL310
configuration, but based on the boardfile code and poking registers
from the Boot Monitor, it would seem to be 8 sets of 16KB ways.
With that, we can successfully boot to enjoy the fun of mismatched FPUs...
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc51b632c7 upstream.
It seems that recent kernels have a shorter timeout when scanning for
ethernet phys causing us to hit a timeout on boards where the phy's
regulator gets enabled just before scanning, which leads to non working
ethernet.
A 10ms startup delay seems to be enough to fix it, this commit adds a
20ms startup delay just to be safe.
This has been tested on a sun4i-a10-a1000 and sun5i-a10s-wobo-i5 board,
both of which have non-working ethernet on recent kernels without this
fix.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f127089650 upstream.
When a L2 cache controller is used in a system that provides hardware
coherency, the entire outer cache operations are useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
In the current kernel implementation, the outer cache flush range
operation is triggered by the dma_alloc function.
This operation can be take place during runtime and in some
circumstances may lead to the PCIe/PL310 deadlock on Armada 375/38x
SoCs.
This patch extends the __dma_clear_buffer() function to receive a
boolean argument related to the coherency of the system. The same
things is done for the calling functions.
Reported-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43761473c2 upstream.
There is a double fetch problem in audit_log_single_execve_arg()
where we first check the execve(2) argumnets for any "bad" characters
which would require hex encoding and then re-fetch the arguments for
logging in the audit record[1]. Of course this leaves a window of
opportunity for an unsavory application to munge with the data.
This patch reworks things by only fetching the argument data once[2]
into a buffer where it is scanned and logged into the audit
records(s). In addition to fixing the double fetch, this patch
improves on the original code in a few other ways: better handling
of large arguments which require encoding, stricter record length
checking, and some performance improvements (completely unverified,
but we got rid of some strlen() calls, that's got to be a good
thing).
As part of the development of this patch, I've also created a basic
regression test for the audit-testsuite, the test can be tracked on
GitHub at the following link:
* https://github.com/linux-audit/audit-testsuite/issues/25
[1] If you pay careful attention, there is actually a triple fetch
problem due to a strnlen_user() call at the top of the function.
[2] This is a tiny white lie, we do make a call to strnlen_user()
prior to fetching the argument data. I don't like it, but due to the
way the audit record is structured we really have no choice unless we
copy the entire argument at once (which would require a rather
wasteful allocation). The good news is that with this patch the
kernel no longer relies on this strnlen_user() value for anything
beyond recording it in the log, we also update it with a trustworthy
value whenever possible.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3254de6bf7 upstream.
Not doing so might cause IO-Page-Faults when a device uses
an alias request-id and the alias-dte is left in a lower
page-mode which does not cover the address allocated from
the iova-allocator.
Fixes: 492667dacc ('x86/amd-iommu: Remove amd_iommu_pd_table')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b548e786ce upstream.
The default domain for a device might also be
identity-mapped. In this case the kernel would crash when
unity mappings are defined for the device. Fix that by
making sure the domain is a dma_ops domain.
Fixes: 0bb6e243d7 ('iommu/amd: Support IOMMU_DOMAIN_DMA type allocation')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cda7005ba2 upstream.
This domain type is not yet handled in the
iommu_ops->domain_free() call-back. Fix that.
Fixes: 0bb6e243d7 ('iommu/amd: Support IOMMU_DOMAIN_DMA type allocation')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c6d90e2bb upstream.
The implementation of iova_to_phys for the long-descriptor ARM
io-pgtable code always masks with the granule size when inserting the
low virtual address bits into the physical address determined from the
page tables. In cases where the leaf entry is found before the final
level of table (i.e. due to a block mapping), this results in rounding
down to the bottom page of the block mapping. Consequently, the physical
address range batching in the vfio_unmap_unpin is defeated and we end
up taking the long way home.
This patch fixes the problem by masking the virtual address with the
appropriate mask for the level at which the leaf descriptor is located.
The short-descriptor code already gets this right, so no change is
needed there.
Reported-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c365d18a7 upstream.
In 'commit <55d940430ab9> ("iommu/vt-d: Get rid of domain->iommu_lock")',
the error handling path is changed a little, which makes the function
always return 0.
This path fixes this.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Fixes: 55d940430a ('iommu/vt-d: Get rid of domain->iommu_lock')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b54b874fba upstream.
Removal of IOMMU driver cannot be done reliably, so Exynos IOMMU driver
doesn't support this operation. It is essential for system operation, so
it makes sense to prevent unbinding by disabling bind/unbind sysfs
feature for SYSMMU controller driver to avoid kernel ops or trashing
memory caused by such operation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 783011b130 upstream.
unicore32 fails to compile with the following errors.
mm/memory.c: In function ‘__handle_mm_fault’:
mm/memory.c:3381: error:
too many arguments to function ‘arch_vma_access_permitted’
mm/gup.c: In function ‘check_vma_flags’:
mm/gup.c:456: error:
too many arguments to function ‘arch_vma_access_permitted’
mm/gup.c: In function ‘vma_permits_fault’:
mm/gup.c:640: error:
too many arguments to function ‘arch_vma_access_permitted’
Fixes: d61172b4b6 ("mm/core, x86/mm/pkeys: Differentiate instruction fetches")
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7db0b2838 upstream.
We want to recover the open stateid if there is no layout stateid
and/or the stateid argument matches an open stateid.
Otherwise throw out the existing layout and recover from scratch, as
the layout stateid is bad.
Fixes: 183d9e7b11 ("pnfs: rework LAYOUTGET retry handling")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66b53f3258 upstream.
Instead of giving up altogether and falling back to doing I/O
through the MDS, which may make the situation worse, wait for
2 lease periods for the callback to resolve itself, and then
try destroying the existing layout.
Only if this was an attempt at getting a first layout, do we
give up altogether, as the server is clearly crazy.
Fixes: 183d9e7b11 ("pnfs: rework LAYOUTGET retry handling")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b38a1f7c upstream.
The non-retry error path is currently broken and ends up releasing the
reference to the layout twice. It also can end up clearing the
NFS_LAYOUT_FIRST_LAYOUTGET flag twice, causing a race.
In addition, the retry path will fail to decrement the plh_outstanding
counter.
Fixes: 183d9e7b11 ("pnfs: rework LAYOUTGET retry handling")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd257933fa upstream.
nfsd4_lock will take the st_mutex before working with the stateid it
gets, but between the time when we drop the cl_lock and take the mutex,
the stateid could become unhashed (a'la FREE_STATEID). If that happens
the lock stateid returned to the client will be forgotten.
Fix this by first moving the st_mutex acquisition into
lookup_or_create_lock_state. Then, have it check to see if the lock
stateid is still hashed after taking the mutex. If it's not, then put
the stateid and try the find/create again.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42691398be upstream.
When running LTP's nfslock01 test, the Linux client can send a LOCK
and a FREE_STATEID request at the same time. The outcome is:
Frame 324 R OPEN stateid [2,O]
Frame 115004 C LOCK lockowner_is_new stateid [2,O] offset 672000 len 64
Frame 115008 R LOCK stateid [1,L]
Frame 115012 C WRITE stateid [0,L] offset 672000 len 64
Frame 115016 R WRITE NFS4_OK
Frame 115019 C LOCKU stateid [1,L] offset 672000 len 64
Frame 115022 R LOCKU NFS4_OK
Frame 115025 C FREE_STATEID stateid [2,L]
Frame 115026 C LOCK lockowner_is_new stateid [2,O] offset 672128 len 64
Frame 115029 R FREE_STATEID NFS4_OK
Frame 115030 R LOCK stateid [3,L]
Frame 115034 C WRITE stateid [0,L] offset 672128 len 64
Frame 115038 R WRITE NFS4ERR_BAD_STATEID
In other words, the server returns stateid L in a successful LOCK
reply, but it has already released it. Subsequent uses of stateid L
fail.
To address this, protect the generation check in nfsd4_free_stateid
with the st_mutex. This should guarantee that only one of two
outcomes occurs: either LOCK returns a fresh valid stateid, or
FREE_STATEID returns NFS4ERR_LOCKS_HELD.
Reported-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Fix-suggested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 149a4fddd0 upstream.
NFS doesn't expect requests with wb_bytes set to zero and may make
unexpected decisions about how to handle that request at the page IO layer.
Skip request creation if we won't have any wb_bytes in the request.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reviewed-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b8b08cbfb upstream.
Commit 56244ef151 was almost but not quite enough to fix the
reservation math after btrfs_copy_from_user returned partial copies.
Some users are still seeing warnings in btrfs_destroy_inode, and with a
long enough test run I'm able to trigger them as well.
This patch fixes the accounting math again, bringing it much closer to
the way it was before the sectorsize conversion Chandan did. The
problem is accounting for the offset into the page/sector when we do a
partial copy. This one just uses the dirty_sectors variable which
should already be updated properly.
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bcb80143e upstream.
At the start of __tm_recheckpoint() we save the kernel stack pointer
(r1) in SPRG SCRATCH0 (SPRG2) so that we can restore it after the
trecheckpoint.
Unfortunately, the same SPRG is used in the SLB miss handler. If an
SLB miss is taken between the save and restore of r1 to the SPRG, the
SPRG is changed and hence r1 is also corrupted. We can end up with
the following crash when we start using r1 again after the restore
from the SPRG:
Oops: Bad kernel stack pointer, sig: 6 [#1]
SMP NR_CPUS=2048 NUMA pSeries
CPU: 658 PID: 143777 Comm: htm_demo Tainted: G EL X 4.4.13-0-default #1
task: c0000b56993a7810 ti: c00000000cfec000 task.ti: c0000b56993bc000
NIP: c00000000004f188 LR: 00000000100040b8 CTR: 0000000010002570
REGS: c00000000cfefd40 TRAP: 0300 Tainted: G EL X (4.4.13-0-default)
MSR: 8000000300001033 <SF,ME,IR,DR,RI,LE> CR: 02000424 XER: 20000000
CFAR: c000000000008468 DAR: 00003ffd84e66880 DSISR: 40000000 SOFTE: 0
PACATMSCRATCH: 00003ffbc865e680
GPR00: fffffffcfabc4268 00003ffd84e667a0 00000000100d8c38 000000030544bb80
GPR04: 0000000000000002 00000000100cf200 0000000000000449 00000000100cf100
GPR08: 000000000000c350 0000000000002569 0000000000002569 00000000100d6c30
GPR12: 00000000100d6c28 c00000000e6a6b00 00003ffd84660000 0000000000000000
GPR16: 0000000000000003 0000000000000449 0000000010002570 0000010009684f20
GPR20: 0000000000800000 00003ffd84e5f110 00003ffd84e5f7a0 00000000100d0f40
GPR24: 0000000000000000 0000000000000000 0000000000000000 00003ffff0673f50
GPR28: 00003ffd84e5e960 00000000003d0f00 00003ffd84e667a0 00003ffd84e5e680
NIP [c00000000004f188] restore_gprs+0x110/0x17c
LR [00000000100040b8] 0x100040b8
Call Trace:
Instruction dump:
f8a1fff0 e8e700a8 38a00000 7ca10164 e8a1fff8 e821fff0 7c0007dd 7c421378
7db142a6 7c3242a6 38800002 7c810164 <e9c100e0> e9e100e8 ea0100f0 ea2100f8
We hit this on large memory machines (> 2TB) but it can also be hit on
smaller machines when 1TB segments are disabled.
To hit this, you also need to be virtualised to ensure SLBs are
periodically removed by the hypervisor.
This patches moves the saving of r1 to the SPRG to the region where we
are guaranteed not to take any further SLB misses.
Fixes: 98ae22e15b ("powerpc: Add helper functions for transactional memory context switching")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b731bcfde upstream.
Propagate errors from kvm_mips_handle_kseg0_tlb_fault() and
kvm_mips_handle_mapped_seg_tlb_fault(), usually triggering an internal
error since they normally indicate the guest accessed bad physical
memory or the commpage in an unexpected way.
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Fixes: e685c689f3 ("KVM/MIPS32: Privileged instruction/target branch emulation.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[james.hogan@imgtec.com: Backport to v4.7]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8985d50382 upstream.
kvm_mips_handle_mapped_seg_tlb_fault() calculates the guest frame number
based on the guest TLB EntryLo values, however it is not range checked
to ensure it lies within the guest_pmap. If the physical memory the
guest refers to is out of range then dump the guest TLB and emit an
internal error.
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[james.hogan@imgtec.com: Backport to v4.7]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c604cffa93 upstream.
kvm_mips_handle_mapped_seg_tlb_fault() appears to map the guest page at
virtual address 0 to PFN 0 if the guest has created its own mapping
there. The intention is unclear, but it may have been an attempt to
protect the zero page from being mapped to anything but the comm page in
code paths you wouldn't expect from genuine commpage accesses (guest
kernel mode cache instructions on that address, hitting trapping
instructions when executing from that address with a coincidental TLB
eviction during the KVM handling, and guest user mode accesses to that
address).
Fix this to check for mappings exactly at KVM_GUEST_COMMPAGE_ADDR (it
may not be at address 0 since commit 42aa12e74e ("MIPS: KVM: Move
commpage so 0x0 is unmapped")), and set the corresponding EntryLo to be
interpreted as 0 (invalid).
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[james.hogan@imgtec.com: Backport to v4.7]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b4d008787 upstream.
Since systemd is consistently using /dev/urandom before it is
initialized, we can't see the other potentially dangerous users of
/dev/urandom immediately after boot. So print the first ten such
complaints instead.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3371f3da08 upstream.
If we have a hardware RNG and are using the in-kernel rngd, we should
use this to initialize the non-blocking pool so that getrandom(2)
doesn't block unnecessarily.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1132deac0 upstream.
get_random_long() reads from the get_random_int_hash array using an
unsigned long pointer. For this code to be guaranteed correct on all
architectures, the array must be aligned to an unsigned long boundary.
Signed-off-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b44f2d18a upstream.
The Hyper-V Linux Integration Services use the VMBus implementation for
communication with the Hypervisor. VMBus registers its own interrupt
handler that completely bypasses the common Linux interrupt handling.
This implies that the interrupt entropy collector is not triggered.
This patch adds the interrupt entropy collection callback into the VMBus
interrupt handler function.
Signed-off-by: Stephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7893242e24 upstream.
During following a symbolic link we received err_buf from SMB2_open().
While the validity of SMB2 error response is checked previously
in smb2_check_message() a symbolic link payload is not checked at all.
Fix it by adding such checks.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd975d1eea upstream.
The secmech hmac(md5) structures are present in the TCP_Server_Info
struct and can be shared among multiple CIFS sessions. However, the
server mutex is not currently held when these structures are allocated
and used, which can lead to a kernel crashes, as in the scenario below:
mount.cifs(8) #1 mount.cifs(8) #2
Is secmech.sdeschmaccmd5 allocated?
// false
Is secmech.sdeschmaccmd5 allocated?
// false
secmech.hmacmd = crypto_alloc_shash..
secmech.sdeschmaccmd5 = kzalloc..
sdeschmaccmd5->shash.tfm = &secmec.hmacmd;
secmech.sdeschmaccmd5 = kzalloc
// sdeschmaccmd5->shash.tfm
// not yet assigned
crypto_shash_update()
deref NULL sdeschmaccmd5->shash.tfm
Unable to handle kernel paging request at virtual address 00000030
epc : 8027ba34 crypto_shash_update+0x38/0x158
ra : 8020f2e8 setup_ntlmv2_rsp+0x4bc/0xa84
Call Trace:
crypto_shash_update+0x38/0x158
setup_ntlmv2_rsp+0x4bc/0xa84
build_ntlmssp_auth_blob+0xbc/0x34c
sess_auth_rawntlmssp_authenticate+0xac/0x248
CIFS_SessSetup+0xf0/0x178
cifs_setup_session+0x4c/0x84
cifs_get_smb_ses+0x2c8/0x314
cifs_mount+0x38c/0x76c
cifs_do_mount+0x98/0x440
mount_fs+0x20/0xc0
vfs_kern_mount+0x58/0x138
do_mount+0x1e8/0xccc
SyS_mount+0x88/0xd4
syscall_common+0x30/0x54
Fix this by locking the srv_mutex around the code which uses these
hmac(md5) structures. All the other secmech algos already have similar
locking.
Fixes: 95dc8dd14e ("Limit allocation of crypto mechanisms to dialect which requires")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b782fcc1cb upstream.
adfeb3e0 ("cifs: Make echo interval tunable") added a comparison of
vol->echo_interval to server->echo_interval as a criterium to
match_server(), but:
(1) A default value is set for server->echo_interval but not for
vol->echo_interval, meaning these can never match if the echo_interval
option is not specified.
(2) vol->echo_interval is in seconds but server->echo_interval is in
jiffies, meaning these can never match even if the echo_interval option
is specified.
This broke TCP session reuse since match_server() can never return 1.
Fix it.
Fixes: adfeb3e0 ("cifs: Make echo interval tunable")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d9535b6ef upstream.
When opening a file with O_CREAT flag, check to see if the file opened
is an existing directory.
This prevents the directory from being opened which subsequently causes
a crash when the close function for directories cifs_closedir() is called
which frees up the file->private_data memory while the file is still
listed on the open file list for the tcon.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reported-by: Xiaoli Feng <xifeng@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6b5058faf upstream.
if, when mounting //HOST/share/sub/dir/foo we can query /sub/dir/foo but
not any of the path components above:
- store the /sub/dir/foo prefix in the cifs super_block info
- in the superblock, set root dentry to the subpath dentry (instead of
the share root)
- set a flag in the superblock to remember it
- use prefixpath when building path from a dentry
fixes bso#8950
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abcfb5d979 upstream.
The jbd2 journal stores the commit time in 64-bit seconds and 32-bit
nanoseconds, which avoids an overflow in 2038, but it gets the numbers
from current_kernel_time(), which uses 'long' seconds on 32-bit
architectures.
This simply changes the code to call current_kernel_time64() so
we use 64-bit seconds consistently.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4dff28740 upstream.
page should be calculated using physical address.
If platform uses non-trivial dma-to-phys memory translation,
dma_handle should be converted to physicval address before
calculation of page.
Failing to do so results in struct page * pointing to
wrong or non-existent memory.
Fixes: f2e3d55397 ("ARC: dma: reintroduce platform specific dma<->phys")
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3925a16ae9 upstream.
LTP madvise05 was generating mm splat
| [ARCLinux]# /sd/ltp/testcases/bin/madvise05
| BUG: Bad page map in process madvise05 pte:80e08211 pmd:9f7d4000
| page:9fdcfc90 count:1 mapcount:-1 mapping: (null) index:0x0 flags: 0x404(referenced|reserved)
| page dumped because: bad pte
| addr:200b8000 vm_flags:00000070 anon_vma: (null) mapping: (null) index:1005c
| file: (null) fault: (null) mmap: (null) readpage: (null)
| CPU: 2 PID: 6707 Comm: madvise05
And for newer kernels, the system was rendered unusable afterwards.
The problem was mprotect->pte_modify() clearing PTE_SPECIAL (which is
set to identify the special zero page wired to the pte).
When pte was finally unmapped, special casing for zero page was not
done, and instead it was treated as a "normal" page, tripping on the
map counts etc.
This fixes ARC STAR 9001053308
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2e12e66a9 upstream.
rproc_add adds the newly created remoteproc to a list for use by
rproc_get_by_phandle and then does some additional processing to finish
adding the remoteproc. This leaves a small window of time in which the
rproc is available in the list but not yet fully initialized, so if
another driver comes along and gets a handle to the rproc, it will be
invalid. Rearrange the code in rproc_add to make sure the rproc is added
to the list only after it has been successfuly initialized.
Fixes: fec47d8635 ("remoteproc: introduce rproc_get_by_phandle API")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76bc8e2843 upstream.
This does not work and does not make sense. So instead of fixing it
(probably not hard) just disallow.
Reported-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67f8ecc550 upstream.
Many devices use userspace bluetooth stacks like BlueZ or Bluedroid in combination
with uhid. If any of these stacks is used with a HID device for which the driver
performs a HID request as part .probe (or technically another HID operation),
this results in a deadlock situation. The deadlock results in a 5 second timeout
for I/O operations in HID drivers, so isn't fatal, but none of the I/O operations
have a chance of succeeding.
The root cause for the problem is that uhid only allows for one request to be
processed at a time per uhid instance and locks out other operations. This means
that if a user space is creating a new HID device through 'UHID_CREATE', which
ultimately triggers '.probe' through the HID layer. Then any HID request e.g. a
read for calibration data would trigger a HID operation on uhid again, but it
won't go out to userspace, because it is still stuck in UHID_CREATE.
In addition bluetooth stacks are typically single threaded, so they wouldn't be
able to handle any requests while waiting on uhid.
Lucikly the UHID spec is somewhat flexible and allows for fixing the issue,
without breaking user space. The idea which the patch implements as discussed
with David Herrmann is to decouple adding of a hid device (which triggers .probe)
from UHID_CREATE. The work will kick off roughly once UHID_CREATE completed (or
else will wait a tiny bit of time in .probe for a lock). A HID driver has to call
HID to call 'hid_hw_start()' as part of .probe once it is ready for I/O, which
triggers UHID_START to user space. Any HID operations should function now within
.probe and won't deadlock because userspace is stuck on UHID_CREATE.
We verified this patch on Bluedroid with Android 6.0 and on desktop Linux with
BlueZ stacks. Prior to the patch they had the deadlock issue.
[jkosina@suse.cz: reword subject]
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9083160c2 upstream.
There was an issue reported by Lucz Geza on Dell Perc 6i. As per issue
reported, megaraid_sas driver goes into an infinite error reporting loop
as soon as there is a change in the status of one of the
arrays (degrade, resync online etc ). Below are the error logs reported
continuously-
Jun 25 08:49:30 ns8 kernel: [ 757.757017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.778017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.799017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.820018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.841018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
This issue is very much specific to controllers which do not support
DCMD- MR_DCMD_PD_LIST_QUERY. In case of any hotplugging/rescanning of
drives, AEN thread will be scheduled by driver and fire DCMD-
MR_DCMD_PD_LIST_QUERY and if this DCMD is failed then driver will fail
this event processing and will not go ahead for further events. This
will cause infinite loop of same event getting retried infinitely and
causing above mentioned logs.
Fix for this problem is: not to fire DCMD MR_DCMD_PD_LIST_QUERY for
controllers which do not support it and send DCMD SUCCESS status to AEN
function so that it can go ahead with other event processing.
Reported-by: Lucz Geza <geza@lucz.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bba142957e upstream.
c44696fff0 ("EDAC: Remove arbitrary limit on number of channels")
lifted the arbitrary limit on memory controller channels in EDAC.
However, the dynamic channel attributes dynamic_csrow_dimm_attr and
dynamic_csrow_ce_count_attr remained 6.
This wasn't a problem except channels 6 and 7 weren't visible in sysfs
on machines with more than 6 channels after the conversion to static
attr groups with
2c1946b6d6 ("EDAC: Use static attribute groups for managing sysfs entries")
[ without that, we're exploding in edac_create_sysfs_mci_device()
because we're dereferencing out of the bounds of the
dynamic_csrow_dimm_attr array. ]
Add attributes for channels 6 and 7 along with a guard for the
future, should more channels be required and/or to sanity check for
misconfigured machines.
We still need to check against the number of channels present on the MC
first, as Thor reported.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reported-by: Hironobu Ishii <ishii.hironobu@jp.fujitsu.com>
Tested-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23bc6ab0a0 upstream.
When we retrieve imtu value from userspace we should use 16 bit pointer
cast instead of 32 as it's defined that way in headers. Fixes setsockopt
calls on big-endian platforms.
Signed-off-by: Amadeusz Sławiński <amadeusz.slawinski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 152bc19e2f upstream.
It seems the commit e5262d0568 ("spi: spi-pxa2xx: SPI support for Intel Quark
X1000") misses one place to be adapted for Intel Quark, i.e. in reset_sccr1().
Clear all RFT bits when call reset_sccr1() on Intel Quark.
Fixes: e5262d0568 ("spi: spi-pxa2xx: SPI support for Intel Quark X1000")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dd91d52a8 upstream.
There is the only failure path in efm32_i2c_probe(),
where clk_disable_unprepare() is missed.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 1b5b23718b ("i2c: efm32: new bus driver")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bea0512c3 upstream.
After discovering there are 2 very different 14e4:4365 PCI devices we
made ID tables less generic. Back then we believed there are only 2 such
devices:
1) 14e4:4365 1028:0016 with SoftMAC BCM43142 chipset
2) 14e4:4365 14e4:4365 with FullMAC BCM4366 chipset
>From the recent report it appears there is also 14e4:4365 105b:e092
which should be claimed by bcma. Add back support for it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=121881
Fixes: 515b399c9a ("bcma: claim only 14e4:4365 PCI Dell card with SoftMAC BCM43142")
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16c3ebfa6 upstream.
Upon firmware load interrupt (FH_TX), the ISR re-enables the
firmware load interrupt only to avoid races with other
flows as described in the commit below. When the firmware
is completely loaded, the thread that is loading the
firmware will enable all the interrupts to make sure that
the driver gets the ALIVE interrupt.
The problem with that is that the thread that is loading
the firmware is actually racing against the ISR and we can
get to the following situation:
CPU0 CPU1
iwl_pcie_load_given_ucode
...
iwl_pcie_load_firmware_chunk
wait_for_interrupt
<interrupt>
ISR handles CSR_INT_BIT_FH_TX
ISR wakes up the thread on CPU0
/* enable all the interrupts
* to get the ALIVE interrupt
*/
iwl_enable_interrupts
ISR re-enables CSR_INT_BIT_FH_TX only
/* start the firmware */
iwl_write32(trans, CSR_RESET, 0);
BUG! ALIVE interrupt will never arrive since it has been
masked by CPU1.
In order to fix that, change the ISR to first check if
STATUS_INT_ENABLED is set. If so, re-enable all the
interrupts. If STATUS_INT_ENABLED is clear, then we can
check what specific interrupt happened and re-enable only
that specific interrupt (RFKILL or FH_TX).
All the credit for the analysis goes to Kirtika who did the
actual debugging work.
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2aabdbdc17 upstream.
The NIC's CPU gets started after the firmware has been
written to its memory. The first thing it does is to
send an interrupt to let the driver know that it is
running. In order to get that interrupt, the driver needs
to make sure it is not masked. Of course, the interrupt
needs to be enabled in the driver before the CPU starts to
run.
I mistakenly inversed those two steps leading to races
which prevented the driver from getting the alive interrupt
from the firmware.
Fix that.
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 602d1657c6 upstream.
do_div was replaced with div64_u64 at some point, causing a bug with
block calculation due to incompatible semantics of the two functions.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Fixes: a739ff3f54 ("dm verity: add support for forward error correction")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6311f1261f upstream.
When s5p_mfc_remove() calls put_device() for the reserved memory region
devs, the driver core warns that the dev doesn't have a release callback:
WARNING: CPU: 0 PID: 591 at drivers/base/core.c:251 device_release+0x8c/0x90
Device 's5p-mfc-l' does not have a release() function, it is broken and must be fixed.
Also, the declared DMA memory using dma_declare_coherent_memory() isn't
relased so add a dev .release that calls dma_release_declared_memory().
Fixes: 6e83e6e25e ("[media] s5p-mfc: Fix kernel warning on memory init")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29debab0a9 upstream.
The devices don't have a name set, so makes dev_name() returns NULL which
makes harder to identify the devices that are causing issues, for example:
WARNING: CPU: 2 PID: 616 at drivers/base/core.c:251 device_release+0x8c/0x90
Device '(null)' does not have a release() function, it is broken and must be fixed.
And after setting the device name:
WARNING: CPU: 0 PID: 591 at drivers/base/core.c:251 device_release+0x8c/0x90
Device 's5p-mfc-l' does not have a release() function, it is broken and must be fixed.
Fixes: 6e83e6e25e ("[media] s5p-mfc: Fix kernel warning on memory init")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28b783e47a upstream.
In xfs_finish_page_writeback(), we have a loop that looks like this:
do {
if (off < bvec->bv_offset)
goto next_bh;
if (off > end)
break;
bh->b_end_io(bh, !error);
next_bh:
off += bh->b_size;
} while ((bh = bh->b_this_page) != head);
The b_end_io function is end_buffer_async_write(), which will call
end_page_writeback() once all the buffers have marked as no longer
under IO. This issue here is that the only thing currently
protecting both the bufferhead chain and the page from being
reclaimed is the PageWriteback state held on the page.
While we attempt to limit the loop to just the buffers covered by
the IO, we still read from the buffer size and follow the next
pointer in the bufferhead chain. There is no guarantee that either
of these are valid after the PageWriteback flag has been cleared.
Hence, loops like this are completely unsafe, and result in
use-after-free issues. One such problem was caught by Calvin Owens
with KASAN:
.....
INFO: Freed in 0x103fc80ec age=18446651500051355200 cpu=2165122683 pid=-1
free_buffer_head+0x41/0x90
__slab_free+0x1ed/0x340
kmem_cache_free+0x270/0x300
free_buffer_head+0x41/0x90
try_to_free_buffers+0x171/0x240
xfs_vm_releasepage+0xcb/0x3b0
try_to_release_page+0x106/0x190
shrink_page_list+0x118e/0x1a10
shrink_inactive_list+0x42c/0xdf0
shrink_zone_memcg+0xa09/0xfa0
shrink_zone+0x2c3/0xbc0
.....
Call Trace:
<IRQ> [<ffffffff81e8b8e4>] dump_stack+0x68/0x94
[<ffffffff8153a995>] print_trailer+0x115/0x1a0
[<ffffffff81541174>] object_err+0x34/0x40
[<ffffffff815436e7>] kasan_report_error+0x217/0x530
[<ffffffff81543b33>] __asan_report_load8_noabort+0x43/0x50
[<ffffffff819d651f>] xfs_destroy_ioend+0x3bf/0x4c0
[<ffffffff819d69d4>] xfs_end_bio+0x154/0x220
[<ffffffff81de0c58>] bio_endio+0x158/0x1b0
[<ffffffff81dff61b>] blk_update_request+0x18b/0xb80
[<ffffffff821baf57>] scsi_end_request+0x97/0x5a0
[<ffffffff821c5558>] scsi_io_completion+0x438/0x1690
[<ffffffff821a8d95>] scsi_finish_command+0x375/0x4e0
[<ffffffff821c3940>] scsi_softirq_done+0x280/0x340
Where the access is occuring during IO completion after the buffer
had been freed from direct memory reclaim.
Prevent use-after-free accidents in this end_io processing loop by
pre-calculating the loop conditionals before calling bh->b_end_io().
The loop is already limited to just the bufferheads covered by the
IO in progress, so the offset checks are sufficient to prevent
accessing buffers in the chain after end_page_writeback() has been
called by the the bh->b_end_io() callout.
Yet another example of why Bufferheads Must Die.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reported-and-Tested-by: Calvin Owens <calvinowens@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eaf9a7361f upstream.
Otherwise, there is potential for both DMF_SUSPENDED* and
DMF_NOFLUSH_SUSPENDING to not be set during dm_suspend() -- which is
definitely _not_ a valid state.
This fix, in conjuction with "dm rq: fix the starting and stopping of
blk-mq queues", addresses the potential for request-based DM multipath's
__multipath_map() to see !dm_noflush_suspending() during suspend.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd9f55ea1c upstream.
Commit d548b34b06 ("dm: reduce the queue delay used in dm_request_fn
from 100ms to 10ms") always intended the value to be 10 msecs -- it
just expressed it in jiffies because earlier commit 7eaceaccab ("block:
remove per-queue plugging") did.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fixes: d548b34b06 ("dm: reduce the queue delay used in dm_request_fn from 100ms to 10ms")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04c16b84e4 upstream.
This patch fixes some of the LDOs and BUCKs voltage range as per
user manual of s2mps15 (REV0.4).
Fixes: 51af206758 ("regulator: s2mps11: Add support for S2MPS15 regulators")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbdb34c90a upstream.
Fix RC5 decoding with Fintek CIR chipset
Commit e87b540be2 tightened up the RC5
decoding by adding a check for trailing silence to ensure a valid RC5
command had been received. Unfortunately the trailer length checked was
10 units and the Fintek CIR device does not want to provide details of a
space longer than 6350us. This meant that RC5 remotes working on a
Fintek setup on 3.16 failed on 3.17 and later. Fix this by shortening
the trailer check to 6 units (allowing for a previous space in the
received remote command).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117221
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 126f402984 upstream.
An earlier patch fixing an input validation issue introduced another
issue: vb2_core_dqbuf() is called with pb argument value NULL in some
cases, causing a NULL pointer dereference. Fix this by skipping the
verification as there's nothing to verify.
Fixes: e7e0c3e265 ("[media] videobuf2-core: Check user space planes array in dqbuf")
Signed-off-by: David R <david@unsolicited.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83934b75c3 upstream.
When a buffer is being dequeued using VIDIOC_DQBUF IOCTL, the exact buffer
which will be dequeued is not known until the buffer has been removed from
the queue. The number of planes is specific to a buffer, not to the queue.
This does lead to the situation where multi-plane buffers may be requested
and queued with n planes, but VIDIOC_DQBUF IOCTL may be passed an argument
struct with fewer planes.
__fill_v4l2_buffer() however uses the number of planes from the dequeued
videobuf2 buffer, overwriting kernel memory (the m.planes array allocated
in video_usercopy() in v4l2-ioctl.c) if the user provided fewer
planes than the dequeued buffer had. Oops!
Fixes: b0e0e1f83d ("[media] media: videobuf2: Prepare to divide videobuf2")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cac1f67ea upstream.
If a system configures the Nuvoton chip to use the alternative
EFM IO address (CR_EFIR2) then after probing the primary EFM IO
address (CR_EFIR) this region is not released.
If a driver for another function of the Nuvoton Super I/O
chip uses the same probing mechanism then it will hang if
loaded after the nuvoton-cir driver.
This was reported for the nct6775 hwmon driver.
Fix this by properly releasing the region after probing CR_EFIR.
This regression was introduced with kernel 4.6 so cc it to stable.
Reported-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca6e6126db upstream.
Implement memory barriers according to Documentation/circular-buffers.txt:
- use smp_store_release() to update ringbuffer read/write pointers
- use smp_load_acquire() to load write pointer on reader side
- use ACCESS_ONCE() to load read pointer on writer side
This fixes data stream corruptions observed e.g. on an ARM Cortex-A9
quad core system with different types (PCI, USB) of DVB tuners.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a00932f08 upstream.
When disconnecting the usbtv device, the sound card is unregistered
from ALSA and the snd member of the usbtv struct is set to NULL. If
the usbtv snd_trigger work is running, this can cause a race condition
where the kernel will attempt to access free'd resources, shown in
[1].
This patch fixes the disconnection code by cancelling any snd_trigger
work before unregistering the sound card from ALSA and checking that
the snd member still exists in the work function.
[1]:
usb 3-1.2: USB disconnect, device number 6
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff81093850>] process_one_work+0x30/0x480
PGD 405bbf067 PUD 405bbe067 PMD 0
Call Trace:
[<ffffffff81093ce8>] worker_thread+0x48/0x4e0
[<ffffffff81093ca0>] ? process_one_work+0x480/0x480
[<ffffffff81093ca0>] ? process_one_work+0x480/0x480
[<ffffffff81099998>] kthread+0xd8/0xf0
[<ffffffff815c73c2>] ret_from_fork+0x22/0x40
[<ffffffff810998c0>] ? kthread_worker_fn+0x170/0x170
---[ end trace 0f3dac5c1a38e610 ]---
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Tested-by: Peter Sutton <foxxy@foxdogstudios.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f37be01e6d upstream.
The RPM has two sets of selectors (IPC bit fields): request and
acknowledge. Apparently, some models use 4*32 bit words for select
and some use 7*32 bit words for request, but all use 7*32 words
for acknowledge bits.
So apparently you can on the models with requests of 4*32 select
bits send 4*32 messages and get 7*32 different replies, so on ACK
interrupt, 7*32 bit words need to be read. This is how the vendor
code apparently works.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9835f1b70b upstream.
The RPM in MSM8660/APQ8060 has different offsets to the selector
ACK and request context ACK registers. Make all these register
offsets part of the per-SoC data and assign the right values.
The bug was found by verifying backwards to the vendor tree in
the out-of-tree files <mach/rpm-[8660|8064|8960]>: all were using
offsets 3,11,15,23 and a select size of 4, except the MSM8660/APQ8060
which was using offsets 3,11,19,27 and a select size of 7.
All other platforms apart from msm8660 were affected by reading
excess registers, since 7 was hardcoded as the number of select
words, this patch makes also this part dynamic so we only write/read
as many select words as the platform actually use.
Symptoms of this bug when using msm8660: the first RPM transaction
would work, but the next would stall or raise an error since the
previous transaction was not properly ACKed as the ACK words were
read at the wrong offset.
Fixes: 58e214382b ("mfd: qcom-rpm: Driver for the Qualcomm RPM")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fc8f707a2 upstream.
If MSR_CONFIG_TDP_CONTROL is locked, we currently try to address some
MSR 0x80000648 or so. Mask out the relevant level bits 0 and 1.
Found while running over the Jailhouse hypervisor which became upset
about this strange MSR index.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c427c42cd6 upstream.
Commit 1e133ab296 ("s390/mm: split arch/s390/mm/pgtable.c") changed
the return value of get_guest_storage_key to an unsigned char, resulting
in -EFAULT getting interpreted as a valid storage key.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f045402984 upstream.
__tlb_flush_asce() should never be used if multiple asce belong to a mm.
As this function changes mm logic determining if local or global tlb
flushes will be neded, we might end up flushing only the gmap asce on all
CPUs and a follow up mm asce flushes will only flush on the local CPU,
although that asce ran on multiple CPUs.
The missing tlb flushes will provoke strange faults in user space and even
low address protections in user space, crashing the kernel.
Fixes: 1b948d6cae ("s390/mm,tlb: optimize TLB flushing for zEC12")
Reported-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f5d050cea upstream.
Prior to commit 1bc6664bdf a call to
enable_cmf for a device for which channel measurement was already
enabled resulted in a reset of the measurement data.
What looked like bugs at the time (a 2nd allocation was triggered
but failed, reset was called regardless of previous failures, and
errors have not been reported to userspace) was actually something
at least one userspace tool depended on. Restore that behavior in
a sane way.
Fixes: 1bc6664bdf ("s390/cio: use device_lock during cmb activation")
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c43203cab1 upstream.
If the processor exits to KVM while delivering an interrupt,
the hypervisor then requeues the interrupt for the next vmentry.
Trying to enter SMM in this same window causes to enter non-root
mode in emulated SMM (i.e. with IF=0) and with a request to
inject an IRQ (i.e. with a valid VM-entry interrupt info field).
This is invalid guest state (SDM 26.3.1.4 "Check on Guest RIP
and RFLAGS") and the processor fails vmentry.
The fix is to defer the injection from KVM_REQ_SMI to KVM_REQ_EVENT,
like we already do for e.g. NMIs. This patch doesn't change the
name of the process_smi function so that it can be applied to
stable releases. The next patch will modify the names so that
process_nmi and process_smi handle respectively KVM_REQ_NMI and
KVM_REQ_SMI.
This is especially common with Windows, probably due to the
self-IPI trick that it uses to deliver deferred procedure
calls (DPCs).
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reported-by: Michał Zegan <webczat_200@poczta.onet.pl>
Fixes: 64d6067057
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f1fe81123 upstream.
When freeing the nested resources of a vcpu, there is an assumption that
the vcpu's vmcs01 is the current VMCS on the CPU that executes
nested_release_vmcs12(). If this assumption is violated, the vcpu's
vmcs01 may be made active on multiple CPUs at the same time, in
violation of Intel's specification. Moreover, since the vcpu's vmcs01 is
not VMCLEARed on every CPU on which it is active, it can linger in a
CPU's VMCS cache after it has been freed and potentially
repurposed. Subsequent eviction from the CPU's VMCS cache on a capacity
miss can result in memory corruption.
It is not sufficient for vmx_free_vcpu() to call vmx_load_vmcs01(). If
the vcpu in question was last loaded on a different CPU, it must be
migrated to the current CPU before calling vmx_load_vmcs01().
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b244c9fc25 upstream.
With PML enabled, guest will shut down if a PML full VMEXIT occurs during
event delivery. According to Intel SDM 27.2.3, PML full VMEXIT can occur when
event is being delivered through IDT, so KVM should not exit to user space
with error. Instead, it should let EXIT_REASON_PML_FULL go through and the
event will be re-injected on the next VMENTRY.
Signed-off-by: Lei Cao <lei.cao@stratus.com>
Fixes: 843e433057 ("KVM: VMX: Add PML support in VMX")
[Shortened the summary and Cc'd stable.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93d17397e4 upstream.
It turns out that if the guest does a H_CEDE while the CPU is in
a transactional state, and the H_CEDE does a nap, and the nap
loses the architected state of the CPU (which is is allowed to do),
then we lose the checkpointed state of the virtual CPU. In addition,
the transactional-memory state recorded in the MSR gets reset back
to non-transactional, and when we try to return to the guest, we take
a TM bad thing type of program interrupt because we are trying to
transition from non-transactional to transactional with a hrfid
instruction, which is not permitted.
The result of the program interrupt occurring at that point is that
the host CPU will hang in an infinite loop with interrupts disabled.
Thus this is a denial of service vulnerability in the host which can
be triggered by any guest (and depending on the guest kernel, it can
potentially triggered by unprivileged userspace in the guest).
This vulnerability has been assigned the ID CVE-2016-5412.
To fix this, we save the TM state before napping and restore it
on exit from the nap, when handling a H_CEDE in real mode. The
case where H_CEDE exits to host virtual mode is already OK (as are
other hcalls which exit to host virtual mode) because the exit
path saves the TM state.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f024ee0984 upstream.
This moves the transactional memory state save and restore sequences
out of the guest entry/exit paths into separate procedures. This is
so that these sequences can be used in going into and out of nap
in a subsequent patch.
The only code changes here are (a) saving and restore LR on the
stack, since these new procedures get called with a bl instruction,
(b) explicitly saving r1 into the PACA instead of assuming that
HSTATE_HOST_R1(r13) is already set, and (c) removing an unnecessary
and redundant setting of MSR[TM] that should have been removed by
commit 9d4d0bdd9e0a ("KVM: PPC: Book3S HV: Add transactional memory
support", 2013-09-24) but wasn't.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfbca61af0 upstream.
In create_safe_exec_page(), we create a copy of the hibernate exit text,
along with some page tables to map this via TTBR0. We then install the
new tables in TTBR0.
In swsusp_arch_resume() we call create_safe_exec_page() before trying a
number of operations which may fail (e.g. copying the linear map page
tables). If these fail, we bail out of swsusp_arch_resume() and return
an error code, but leave TTBR0 as-is. Subsequently, the core hibernate
code will call free_basic_memory_bitmaps(), which will free all of the
memory allocations we made, including the page tables installed in
TTBR0.
Thus, we may have TTBR0 pointing at dangling freed memory for some
period of time. If the hibernate attempt was triggered by a user
requesting a hibernate test via the reboot syscall, we may return to
userspace with the clobbered TTBR0 value.
Avoid these issues by reorganising swsusp_arch_resume() such that we
have no failure paths after create_safe_exec_page(). We also add a check
that the zero page allocation succeeded, matching what we have for other
allocations.
Fixes: 82869ac57b ("arm64: kernel: Add support for hibernate/suspend-to-disk")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0194e760f7 upstream.
In create_safe_exec_page we install a set of global mappings in TTBR0,
then subsequently invalidate TLBs. While TTBR0 points at the zero page,
and the TLBs should be free of stale global entries, we may have stale
ASID-tagged entries (e.g. from the EFI runtime services mappings) for
the same VAs. Per the ARM ARM these ASID-tagged entries may conflict
with newly-allocated global entries, and we must follow a
Break-Before-Make approach to avoid issues resulting from this.
This patch reworks create_safe_exec_page to invalidate TLBs while the
zero page is still in place, ensuring that there are no potential
conflicts when the new TTBR0 value is installed. As a single CPU is
online while this code executes, we do not need to perform broadcast TLB
maintenance, and can call local_flush_tlb_all(), which also subsumes
some barriers. The remaining assembly is converted to use write_sysreg()
and isb().
Other than this, we safely manipulate TTBRs in the hibernate dance. The
code we install as part of the new TTBR0 mapping (the hibernated
kernel's swsusp_arch_suspend_exit) installs a zero page into TTBR1,
invalidates TLBs, then installs its preferred value. Upon being restored
to the middle of swsusp_arch_suspend, the new image will call
__cpu_suspend_exit, which will call cpu_uninstall_idmap, installing the
zero page in TTBR0 and invalidating all TLB entries.
Fixes: 82869ac57b ("arm64: kernel: Add support for hibernate/suspend-to-disk")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89581f06b2 upstream.
We need to set cpsr before determining the spsr bank, as the bank
depends on the target exception level of the injection, not the
current mode of the vcpu. Normally this is one in the same (EL1),
but not when we manage to trap an EL0 fault. It still doesn't really
matter for the 64-bit EL0 case though, as vcpu_spsr() unconditionally
uses the EL1 bank for that. However the 32-bit EL0 case gets fun, as
that path will lead to the BUG() in vcpu_spsr32().
This patch fixes the assignment order and also modifies some white
space in order to better group pairs of lines that have strict order.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6732fc402 upstream.
Due to the untyped KIMAGE_VADDR constant, the linker may not notice
that the __rela_offset and __dynsym_offset expressions are absolute
values (i.e., are not subject to relocation). This does not matter for
KASLR, but it does confuse kallsyms in relative mode, since it uses
the lowest non-absolute symbol address as the anchor point, and expects
all other symbol addresses to be within 4 GB of it.
Fix this by qualifying these expressions as ABSOLUTE() explicitly.
Fixes: 0cd3defe0a ("arm64: kernel: perform relocation processing from ID map")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04a8481061 upstream.
As reported by Zijun, the fdt_check_header() call in __fixmap_remap_fdt()
is not safe since it is not guaranteed that the FDT header is mapped
completely. Due to the minimum alignment of 8 bytes, the only fields we
can assume to be mapped are 'magic' and 'totalsize'.
Since the OF layer is in charge of validating the FDT image, and we are
only interested in making reasonably sure that the size field contains
a meaningful value, replace the fdt_check_header() call with an explicit
comparison of the magic field's value against the expected value.
Reported-by: Zijun Hu <zijun_hu@htc.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad1cfdf518 upstream.
The 2nd additional region is the GIC virtual cpu interface register
base and size.
As the gic400 of rk3368 says, the cpu interface register map as below
:
-0x0000 GICC_CTRL
.
.
.
-0x00fc GICC_IIDR
-0x1000 GICC_IDR
Obviously, the region size should be greater than 0x1000.
So we should make sure to include the GICC_IDR since the kernel will access
it in some cases.
Fixes: b790c2cab5 ("arm64: dts: add Rockchip rk3368 core dtsi and board dts for the r88 board")
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[added Fixes and stable-cc]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
commit 0bd50d719b upstream.
Due to a silicon issue on the Atom X5-Z8000 "Cherry Trail" processor
series, a common lock must be used to prevent concurrent accesses
across the 4 GPIO controllers managed by this driver.
See Intel Atom Z8000 Processor Series Specification Update
(Rev. 005), errata #CHT34, for further information.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd3b204af1 upstream.
The error handling is not correct since the commit 3f7dbfd8ee ("gpio:
intel-mid: switch to using gpiolib irqchip helpers"). Switch to devres API to
fix the potential resource leak.
Fixes: commit 3f7dbfd8ee ("gpio: intel-mid: switch to using gpiolib irqchip helpers")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dbd3212f8 upstream.
The commit d56d6b3d7d ("gpio: langwell: add Intel Merrifield support")
doesn't look at all as a proper support for Intel Merrifield and I dare to say
that it distorts the behaviour of the hardware.
The register map is different on Intel Merrifield, i.e. only 6 out of 8
register have the same purpose but none of them has same location in the
address space. The current case potentially harmful to existing hardware since
it's poking registers on wrong offsets and may set some pin to be GPIO output
when connected hardware doesn't expect such.
Besides the above GPIO and pinctrl on Intel Merrifield have been located in
different IP blocks. The functionality has been extended as well, i.e. added
support of level interrupts, special registers for wake capable sources and
thus, in my opinion, requires a completele separate driver.
If someone wondering the existing gpio-intel-mid.c would be converted to actual
pinctrl (which by the fact it is now), though I wouldn't be a volunteer to do
that.
Fixes: d56d6b3d7d ("gpio: langwell: add Intel Merrifield support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a246b8198f upstream.
NBANK() macro assumes that ngpios is a multiple of 8(BANK_SZ) and
hence results in 0 banks for PCA9536 which has just 4 gpios. This is
wrong as PCA9356 has 1 bank with 4 gpios. This results in uninitialized
PCA953X_INVERT register. Fix this by using DIV_ROUND_UP macro in
NBANK().
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e51e4d8a18 upstream.
When the clk_get() of "uart" clock returns EPROBE_DEFER, the next re-probe
finishes with success but uses invalid (ERR_PTR) values. This leads to
dereferencing of ERR_PTR stored under ourport->clk:
12c30000.serial: Controller clock not found
(...)
12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10
Unable to handle kernel paging request at virtual address fffffdfb
(clk_prepare) from [<c039f7d0>] (s3c24xx_serial_pm+0x20/0x128)
(s3c24xx_serial_pm) from [<c0395414>] (uart_change_pm+0x38/0x40)
(uart_change_pm) from [<c039689c>] (uart_add_one_port+0x31c/0x44c)
(uart_add_one_port) from [<c03a035c>] (s3c24xx_serial_probe+0x2a8/0x418)
(s3c24xx_serial_probe) from [<c03ee110>] (platform_drv_probe+0x50/0xb0)
(platform_drv_probe) from [<c03ecb44>] (driver_probe_device+0x1f4/0x2b0)
(driver_probe_device) from [<c03eb0c0>] (bus_for_each_drv+0x44/0x8c)
(bus_for_each_drv) from [<c03ec8c8>] (__device_attach+0x9c/0x100)
(__device_attach) from [<c03ebf54>] (bus_probe_device+0x84/0x8c)
(bus_probe_device) from [<c03ec388>] (deferred_probe_work_func+0x60/0x8c)
(deferred_probe_work_func) from [<c012fee4>] (process_one_work+0x120/0x328)
(process_one_work) from [<c0130150>] (worker_thread+0x2c/0x4ac)
(worker_thread) from [<c0135320>] (kthread+0xd8/0xf4)
(kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
The first unsuccessful clk_get() causes s3c24xx_serial_init_port() to
exit with failure but the s3c24xx_uart_port is left half-configured
(e.g. port->mapbase is set, clk contains ERR_PTR). On next re-probe,
the function s3c24xx_serial_init_port() will exit early with success
because of configured port->mapbase and driver will use old values,
including the ERR_PTR as clock.
Fix this by cleaning the port->mapbase on error path so each re-probe
will initialize all of the port settings.
Fixes: 60e9357547 ("serial: samsung: enable clock before clearing pending interrupts during init")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30acf549ca upstream.
For dm uarts in pio mode tx data is transferred to the fifo register 4
bytes at a time, but care is not taken when these 4 bytes spans the end
of the xmit buffer so the loop might read up to 3 bytes past the buffer
and then skip the actual data at the beginning of the buffer.
Fix this by, analogous to the DMA case, make sure the chunk doesn't
wrap the xmit buffer.
Fixes: 3a878c430f ("tty: serial: msm: Add TX DMA support")
Cc: Ivan Ivanov <iivanov.xz@gmail.com>
Reported-by: Frank Rowand <frowand.list@gmail.com>
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Frank Rowand <frank.rowand@am.sony.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e75118a7b5 upstream.
Passing "nosmp" should boot the kernel with a single processor, without
provision to enable secondary CPUs even if they are present. "nosmp" is
implemented by setting maxcpus=0. At the moment we still mark the secondary
CPUs present even with nosmp, which allows the userspace to bring them
up. This patch corrects the smp_prepare_cpus() to honor the maxcpus == 0.
Commit 44dbcc93ab ("arm64: Fix behavior of maxcpus=N") fixed the
behavior for maxcpus >= 1, but broke maxcpus = 0.
Fixes: 44dbcc93ab ("arm64: Fix behavior of maxcpus=N")
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
[catalin.marinas@arm.com: updated code comment]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9c220b589 upstream.
Selecting CONFIG_RANDOMIZE_BASE=y and CONFIG_MODULES=n fails to build
the module PLTs support:
CC arch/arm64/kernel/module-plts.o
/work/Linux/linux-2.6-aarch64/arch/arm64/kernel/module-plts.c: In function ‘module_emit_plt_entry’:
/work/Linux/linux-2.6-aarch64/arch/arm64/kernel/module-plts.c:32:49: error: dereferencing pointer to incomplete type ‘struct module’
This patch selects ARM64_MODULE_PLTS conditionally only if MODULES is
enabled.
Fixes: f80fb3a3d5 ("arm64: add support for kernel ASLR")
Reported-by: Jeff Vander Stoep <jeffv@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9113c2aa05 upstream.
In smp_prepare_boot_cpu(), we invoke cpuinfo_store_boot_cpu to store
the cpuinfo in a per-cpu ptr, before initialising the per-cpu offset for
the boot CPU. This patch reorders the sequence to make sure we initialise
the per-cpu offset before accessing the per-cpu area.
Commit 4b998ff188 ("arm64: Delay cpuinfo_store_boot_cpu") fixed the
issue where we modified the per-cpu area even before the kernel initialises
the per-cpu areas, but failed to wait until the boot cpu updated it's
offset.
Fixes: 4b998ff188 ("arm64: Delay cpuinfo_store_boot_cpu")
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ce39ad151 upstream.
Clearing PSTATE.D is one of the requirements for generating a debug
exception. The arm64 booting protocol requires that PSTATE.D is set,
since many of the debug registers (for example, the hw_breakpoint
registers) are UNKNOWN out of reset and could potentially generate
spurious, fatal debug exceptions in early boot code if PSTATE.D was
clear. Once the debug registers have been safely initialised, PSTATE.D
is cleared, however this is currently broken for two reasons:
(1) The boot CPU clears PSTATE.D in a postcore_initcall and secondary
CPUs clear PSTATE.D in secondary_start_kernel. Since the initcall
runs after SMP (and the scheduler) have been initialised, there is
no guarantee that it is actually running on the boot CPU. In this
case, the boot CPU is left with PSTATE.D set and is not capable of
generating debug exceptions.
(2) In a preemptible kernel, we may explicitly schedule on the IRQ
return path to EL1. If an IRQ occurs with PSTATE.D set in the idle
thread, then we may schedule the kthread_init thread, run the
postcore_initcall to clear PSTATE.D and then context switch back
to the idle thread before returning from the IRQ. The exception
return path will then restore PSTATE.D from the stack, and set it
again.
This patch fixes the problem by moving the clearing of PSTATE.D earlier
to proc.S. This has the desirable effect of clearing it in one place for
all CPUs, long before we have to worry about the scheduler or any
exception handling. We ensure that the previous reset of MDSCR_EL1 has
completed before unmasking the exception, so that any spurious
exceptions resulting from UNKNOWN debug registers are not generated.
Without this patch applied, the kprobes selftests have been seen to fail
under KVM, where we end up attempting to step the OOL instruction buffer
with PSTATE.D set and therefore fail to complete the step.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c47eb1c18 upstream.
The kprobe enablement work has uncovered that changes made by
a guest to MDSCR_EL1 were propagated to the host when VHE was
enabled, leading to unexpected exception being delivered.
Moving this register to the list of registers that are always
context-switched fixes the issue.
Fixes: 9c6c356832 ("arm64: KVM: VHE: Split save/restore of registers shared between guest and host")
Reported-by: Tirumalesh Chalamarla <Tirumalesh.Chalamarla@cavium.com>
Tested-by: Tirumalesh Chalamarla <Tirumalesh.Chalamarla@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fdef69838 upstream.
This patch fixes an issue that the xfer_work() is possible to cause
NULL pointer dereference if the usb cable is disconnected while data
transfer is running.
In such case, a gadget driver may call usb_ep_disable()) before
xfer_work() is actually called. In this case, the usbhs_pkt_pop()
will call usbhsf_fifo_unselect(), and then usbhs_pipe_to_fifo()
in xfer_work() will return NULL.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c0415fa08 upstream.
This patch adds support for 0x1206 PID of Telit LE910.
Since the interfaces positions are the same than the ones for
0x1043 PID of Telit LE922, telit_le922_blacklist_usbcfg3 is used.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cad39fe4e upstream.
commit f3af36511e ("usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers") ended up
regressing Isochronous endpoints by clearing
DWC3_EP_BUSY flag too early, which resulted in
choppy audio playback over USB.
Fix that by partially reverting original commit and
making sure that we check for isochronous endpoints.
Fixes: f3af36511e ("usb: dwc3: gadget: always enable IOC
on bulk/interrupt transfers")
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15e4292a2d upstream.
This patch fixes an issue that the CFIFOSEL register value is possible
to be changed by usbhsg_ep_enable() wrongly. And then, a data transfer
using CFIFO may not work correctly.
For example:
# modprobe g_multi file=usb-storage.bin
# ifconfig usb0 192.168.1.1 up
(During the USB host is sending file to the mass storage)
# ifconfig usb0 down
In this case, since the u_ether.c may call usb_ep_enable() in
eth_stop(), if the renesas_usbhs driver is also using CFIFO for
mass storage, the mass storage may not work correctly.
So, this patch adds usbhs_lock() and usbhs_unlock() calling in
usbhsg_ep_enable() to protect CFIFOSEL register. This is because:
- CFIFOSEL.CURPIPE = 0 is also needed for the pipe configuration
- The CFIFOSEL (fifo->sel) is already protected by usbhs_lock()
Fixes: 97664a207b ("usb: renesas_usbhs: shrink spin lock area")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d23d16a88 upstream.
The above commit reordered spin_lock/unlock and now `&dev->lock' is acquired
(rather than released) before calling `dev->driver->disconnect',
`dev->driver->setup', `dev->driver->suspend', `usb_gadget_giveback_request', and
`usb_gadget_udc_reset'.
But this *may* not be the right way to fix the problem pointed by d3cb25a121.
Note that the other usb/gadget/udc drivers do release the lock before calling
these functions. There are also inconsistencies within pch_udc.c, where
`dev->driver->disconnect' is called while holding `&dev->lock' in lines 613 and
1184, but not in line 2739.
Finally, commit d3cb25a121 may have introduced several potential deadlocks.
For instance, EBA (https://github.com/models-team/eba) reports:
Double lock in drivers/usb/gadget/udc/pch_udc.c
first at 2791: spin_lock(& dev->lock); [pch_udc_isr]
second at 2694: spin_lock(& dev->lock); [pch_udc_svc_cfg_interrupt]
after calling from 2793: pch_udc_dev_isr(dev, dev_intr);
after calling from 2724: pch_udc_svc_cfg_interrupt(dev);
Similarly, other potential deadlocks are 2791 -> 2793 -> 2721 -> 2657; and
2791 -> 2793 -> 2711 -> 2573 -> 1499 -> 1480.
Fixes: d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab2a92e7a6 upstream.
As a micro-power optimization, let's only resume the
USB2 PHY if we're working on <=HIGHSPEED. If we're
gonna work on SUPERSPEED or SUPERSPEED+, there's no
point in resuming the USB2 PHY.
Fixes: 2b0f11df84 ("usb: dwc3: gadget: clear SUSPHY bit before ep cmds")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 554a5ccc4e upstream.
If we hit this error when mounted with errors=continue or
errors=remount-ro:
EXT4-fs error (device loop0): ext4_mb_mark_diskspace_used:2940: comm ext4.exe: Allocating blocks 5090-6081 which overlap fs metadata
then ext4_mb_new_blocks() will call ext4_mb_release_context() and try to
continue. However, ext4_mb_release_context() is the wrong thing to call
here since we are still actually using the allocation context.
Instead, just error out. We could retry the allocation, but there is a
possibility of getting stuck in an infinite loop instead, so this seems
safer.
[ Fixed up so we don't return EAGAIN to userspace. --tytso ]
Fixes: 8556e8f3b6 ("ext4: Don't allow new groups to be added during block allocation")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c65d5c6c81 upstream.
If we encounter a filesystem error during orphan cleanup, we should stop.
Otherwise, we may end up in an infinite loop where the same inode is
processed again and again.
EXT4-fs (loop0): warning: checktime reached, running e2fsck is recommended
EXT4-fs error (device loop0): ext4_mb_generate_buddy:758: group 2, block bitmap and bg descriptor inconsistent: 6117 vs 0 free clusters
Aborting journal on device loop0-8.
EXT4-fs (loop0): Remounting filesystem read-only
EXT4-fs error (device loop0) in ext4_free_blocks:4895: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs error (device loop0) in ext4_ext_remove_space:3068: IO failure
EXT4-fs error (device loop0) in ext4_ext_truncate:4667: Journal has aborted
EXT4-fs error (device loop0) in ext4_orphan_del:2927: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs (loop0): Inode 16 (00000000618192a0): orphan list check failed!
[...]
EXT4-fs (loop0): Inode 16 (0000000061819748): orphan list check failed!
[...]
EXT4-fs (loop0): Inode 16 (0000000061819bf0): orphan list check failed!
[...]
See-also: c9eb13a910 ("ext4: fix hang when processing corrupted orphaned inode list")
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b9554dc5b upstream.
If s_reserved_gdt_blocks is extremely large, it's possible for
ext4_init_block_bitmap(), which is called when ext4 sets up an
uninitialized block bitmap, to corrupt random kernel memory. Add the
same checks which e2fsck has --- it must never be larger than
blocksize / sizeof(__u32) --- and then add a backup check in
ext4_init_block_bitmap() in case the superblock gets modified after
the file system is mounted.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a7fd522a7 upstream.
If ext4_fill_super() fails early, it's possible for ext4_evict_inode()
to call ext4_should_journal_data() before superblock options and flags
are fully set up. In that case, the iput() on the journal inode can
end up causing a BUG().
Work around this problem by reordering the tests so we only call
ext4_should_journal_data() after we know it's not the journal inode.
Fixes: 2d859db3e4 ("ext4: fix data corruption in inodes with journalled data")
Fixes: 2b405bfa84 ("ext4: fix data=journal fast mount/umount hang")
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 646caa9c8e upstream.
Commit 06bd3c36a7 (ext4: fix data exposure after a crash) uncovered a
deadlock in ext4_writepages() which was previously much harder to hit.
After this commit xfstest generic/130 reproduces the deadlock on small
filesystems.
The problem happens when ext4_do_update_inode() sets LARGE_FILE feature
and marks current inode handle as synchronous. That subsequently results
in ext4_journal_stop() called from ext4_writepages() to block waiting for
transaction commit while still holding page locks, reference to io_end,
and some prepared bio in mpd structure each of which can possibly block
transaction commit from completing and thus results in deadlock.
Fix the problem by releasing page locks, io_end reference, and
submitting prepared bio before calling ext4_journal_stop().
[ Changed to defer the call to ext4_journal_stop() only if the handle
is synchronous. --tytso ]
Reported-and-tested-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f70749ca42 upstream.
An extent with lblock = 4294967295 and len = 1 will pass the
ext4_valid_extent() test:
ext4_lblk_t last = lblock + len - 1;
if (len == 0 || lblock > last)
return 0;
since last = 4294967295 + 1 - 1 = 4294967295. This would later trigger
the BUG_ON(es->es_lblk + es->es_len < es->es_lblk) in ext4_es_end().
We can simplify it by removing the - 1 altogether and changing the test
to use lblock + len <= lblock, since now if len = 0, then lblock + 0 ==
lblock and it fails, and if len > 0 then lblock + len > lblock in order
to pass (i.e. it doesn't overflow).
Fixes: 5946d0893 ("ext4: check for overlapping extents in ext4_valid_extent_entries()")
Fixes: 2f974865f ("ext4: check for zero length extent explicitly")
Cc: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2c1659b4f upstream.
As suggested by the serial port infrastructure documentation, the IRQ is
requested in ->startup(). However, it is never freed in the ->shutdown()
hook.
With simple systems that open the serial port once for all and always
have at least one process that keep the serial port opened, there was no
problem. But with a more complicated system (*cough* systemd *cough*),
the serial port is opened/closed many times, which at some point no
processes having the serial port open at all. Due to this ->startup()
gets called again, tries to request_irq() again, which fails.
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f070e81be upstream.
When there is more data to be processed, the current test in
scatterwalk_done may prevent us from calling pagedone even when
we should.
In particular, if we're on an SG entry spanning multiple pages
where the last page is not a full page, we will incorrectly skip
calling pagedone on the second last page.
This patch fixes this by adding a separate test for whether we've
reached the end of a page.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b30bdfa864 upstream.
As it is if you ask for a sync gcm you may actually end up with
an async one because it does not filter out async implementations
of ghash.
This patch fixes this by adding the necessary filter when looking
for ghash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7d3abe1c upstream.
This reverts commit 790d849bf8.
Using a v4.7-rc7 kernel on a HP ProLiant triggered following messages
pcc-cpufreq: (v1.10.00) driver loaded with frequency limits: 1200 MHz, 2800 MHz
cpufreq: ondemand governor failed, too long transition latency of HW, fallback to performance governor
The last line was shown for each CPU in the system.
Testing v4.5 (where commit 790d849b was integrated) triggered
similar messages. Same behaviour on a 2nd HP Proliant system.
So commit 790d849bf (cpufreq: pcc-cpufreq: update default value of
cpuinfo_transition_latency) causes the system to use performance
governor which, I guess, was not the intention of the patch.
Enabling debug output in pcc-cpufreq provides following verbose output:
pcc-cpufreq: (v1.10.00) driver loaded with frequency limits: 1200 MHz, 2800 MHz
pcc_get_offset: for CPU 0: pcc_cpu_data input_offset: 0x44, pcc_cpu_data output_offset: 0x48
init: policy->max is 2800000, policy->min is 1200000
get: get_freq for CPU 0
get: SUCCESS: (virtual) output_offset for cpu 0 is 0xffffc9000d7c0048, contains a value of: 0xff06. Speed is: 168000 MHz
cpufreq: ondemand governor failed, too long transition latency of HW, fallback to performance governor
target: CPU 0 should go to target freq: 2800000 (virtual) input_offset is 0xffffc9000d7c0044
target: was SUCCESSFUL for cpu 0
I am asking to revert 790d849bf to re-enable usage of ondemand
governor with pcc-cpufreq.
Fixes: 790d849bf (cpufreq: pcc-cpufreq: update default value of cpuinfo_transition_latency)
Signed-off-by: Andreas Herrmann <aherrmann@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47be61845c upstream.
We triggered soft-lockup under stress test which
open/access/write/close one file concurrently on more than
five different CPUs:
WARN: soft lockup - CPU#0 stuck for 11s! [who:30631]
...
[<ffffffc0003986f8>] dput+0x100/0x298
[<ffffffc00038c2dc>] terminate_walk+0x4c/0x60
[<ffffffc00038f56c>] path_lookupat+0x5cc/0x7a8
[<ffffffc00038f780>] filename_lookup+0x38/0xf0
[<ffffffc000391180>] user_path_at_empty+0x78/0xd0
[<ffffffc0003911f4>] user_path_at+0x1c/0x28
[<ffffffc00037d4fc>] SyS_faccessat+0xb4/0x230
->d_lock trylock may failed many times because of concurrently
operations, and dput() may execute a long time.
Fix this by replacing cpu_relax() with cond_resched().
dput() used to be sleepable, so make it sleepable again
should be safe.
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e390b2b2f upstream.
This reverts commit f9054c70d2 ("mm, mempool: only set __GFP_NOMEMALLOC
if there are free elements").
There has been a report about OOM killer invoked when swapping out to a
dm-crypt device. The primary reason seems to be that the swapout out IO
managed to completely deplete memory reserves. Ondrej was able to
bisect and explained the issue by pointing to f9054c70d2 ("mm,
mempool: only set __GFP_NOMEMALLOC if there are free elements").
The reason is that the swapout path is not throttled properly because
the md-raid layer needs to allocate from the generic_make_request path
which means it allocates from the PF_MEMALLOC context. dm layer uses
mempool_alloc in order to guarantee a forward progress which used to
inhibit access to memory reserves when using page allocator. This has
changed by f9054c70d2 ("mm, mempool: only set __GFP_NOMEMALLOC if
there are free elements") which has dropped the __GFP_NOMEMALLOC
protection when the memory pool is depleted.
If we are running out of memory and the only way forward to free memory
is to perform swapout we just keep consuming memory reserves rather than
throttling the mempool allocations and allowing the pending IO to
complete up to a moment when the memory is depleted completely and there
is no way forward but invoking the OOM killer. This is less than
optimal.
The original intention of f9054c70d2 was to help with the OOM
situations where the oom victim depends on mempool allocation to make a
forward progress. David has mentioned the following backtrace:
schedule
schedule_timeout
io_schedule_timeout
mempool_alloc
__split_and_process_bio
dm_request
generic_make_request
submit_bio
mpage_readpages
ext4_readpages
__do_page_cache_readahead
ra_submit
filemap_fault
handle_mm_fault
__do_page_fault
do_page_fault
page_fault
We do not know more about why the mempool is depleted without being
replenished in time, though. In any case the dm layer shouldn't depend
on any allocations outside of the dedicated pools so a forward progress
should be guaranteed. If this is not the case then the dm should be
fixed rather than papering over the problem and postponing it to later
by accessing more memory reserves.
mempools are a mechanism to maintain dedicated memory reserves to
guaratee forward progress. Allowing them an unbounded access to the
page allocator memory reserves is going against the whole purpose of
this mechanism.
Bisected by Ondrej Kozina.
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20160721145309.GR26379@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Ondrej Kozina <okozina@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: NeilBrown <neilb@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Ondrej Kozina <okozina@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ebce595f6 upstream.
fuse_flush() calls write_inode_now() that triggers writeback, but actual
writeback will happen later, on fuse_sync_writes(). If an error happens,
fuse_writepage_end() will set error bit in mapping->flags. So, we have to
check mapping->flags after fuse_sync_writes().
Signed-off-by: Maxim Patlasov <mpatlasov@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 4d99ff8f12 ("fuse: Turn writeback cache on")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac7f052b9e upstream.
Due to implementation of fuse writeback filemap_write_and_wait_range() does
not catch errors. We have to do this directly after fuse_sync_writes()
Signed-off-by: Alexey Kuznetsov <kuznet@virtuozzo.com>
Signed-off-by: Maxim Patlasov <mpatlasov@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 4d99ff8f12 ("fuse: Turn writeback cache on")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ce827b4cc upstream.
In kernel bug 150021, a kernel panic was reported when restoring a
hibernate image. Only a picture of the oops was reported, so I can't
paste the whole thing here. But here are the most interesting parts:
kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
BUG: unable to handle kernel paging request at ffff8804615cfd78
...
RIP: ffff8804615cfd78
RSP: ffff8804615f0000
RBP: ffff8804615cfdc0
...
Call Trace:
do_signal+0x23
exit_to_usermode_loop+0x64
...
The RIP is on the same page as RBP, so it apparently started executing
on the stack.
The bug was bisected to commit ef0f3ed5a4 (x86/asm/power: Create
stack frames in hibernate_asm_64.S), which in retrospect seems quite
dangerous, since that code saves and restores the stack pointer from a
global variable ('saved_context').
There are a lot of moving parts in the hibernate save and restore paths,
so I don't know exactly what caused the panic. Presumably, a FRAME_END
was executed without the corresponding FRAME_BEGIN, or vice versa. That
would corrupt the return address on the stack and would be consistent
with the details of the above panic.
[ rjw: One major problem is that by the time the FRAME_BEGIN in
restore_registers() is executed, the stack pointer value may not
be valid any more. Namely, the stack area pointed to by it
previously may have been overwritten by some image memory contents
and that page frame may now be used for whatever different purpose
it had been allocated for before hibernation. In that case, the
FRAME_BEGIN will corrupt that memory. ]
Instead of doing the frame pointer save/restore around the bounds of the
affected functions, just do it around the call to swsusp_save().
That has the same effect of ensuring that if swsusp_save() sleeps, the
frame pointers will be correct. It's also a much more obviously safe
way to do it than the original patch. And objtool still doesn't report
any warnings.
Fixes: ef0f3ed5a4 (x86/asm/power: Create stack frames in hibernate_asm_64.S)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=150021
Reported-by: Andre Reinke <andre.reinke@mailbox.org>
Tested-by: Andre Reinke <andre.reinke@mailbox.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b703305d9 upstream.
Usually, after we have found the proper microcode blob for the current
machine, we stash it away for later use with save_microcode_in_initrd().
However, with builtin microcode which doesn't come from the initrd, we
don't call that function because CONFIG_BLK_DEV_INITRD=n and even if
set, we don't have a valid initrd.
In order to fix this, let's make save_microcode_in_initrd() an
fs_initcall which runs before rootfs_initcall() as this was the time it
was called previously through:
rootfs_initcall(populate_rootfs)
|-> free_initrd()
|-> free_initrd_mem()
|-> save_microcode_in_initrd()
Also, we make it run independently from initrd functionality being
present or not.
And since it is called in the microcode loader only now, we can also
make it static.
Reported-and-tested-by: Jim Bos <jim876@xs4all.nl>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1465225850-7352-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05eb6e7263 upstream.
Radix trees may be used not only for storing page cache pages, so
unconditionally accounting radix tree nodes to the current memory cgroup
is bad: if a radix tree node is used for storing data shared among
different cgroups we risk pinning dead memory cgroups forever.
So let's only account radix tree nodes if it was explicitly requested by
passing __GFP_ACCOUNT to INIT_RADIX_TREE. Currently, we only want to
account page cache entries, so mark mapping->page_tree so.
Fixes: 58e698af4c ("radix-tree: account radix_tree_node to memory cgroup")
Link: http://lkml.kernel.org/r/1470057188-7864-1-git-send-email-vdavydov@virtuozzo.com
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86a574de45 upstream.
Don't allow RNDADDTOENTCNT or RNDADDENTROPY to accept a negative
entropy value. It doesn't make any sense to subtract from the entropy
counter, and it can trigger a warning:
random: negative entropy/overflow: pool input count -40000
------------[ cut here ]------------
WARNING: CPU: 3 PID: 6828 at drivers/char/random.c:670[< none
>] credit_entropy_bits+0x21e/0xad0 drivers/char/random.c:670
Modules linked in:
CPU: 3 PID: 6828 Comm: a.out Not tainted 4.7.0-rc4+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
ffffffff880b58e0 ffff88005dd9fcb0 ffffffff82cc838f ffffffff87158b40
fffffbfff1016b1c 0000000000000000 0000000000000000 ffffffff87158b40
ffffffff83283dae 0000000000000009 ffff88005dd9fcf8 ffffffff8136d27f
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff82cc838f>] dump_stack+0x12e/0x18f lib/dump_stack.c:51
[<ffffffff8136d27f>] __warn+0x19f/0x1e0 kernel/panic.c:516
[<ffffffff8136d48c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:551
[<ffffffff83283dae>] credit_entropy_bits+0x21e/0xad0 drivers/char/random.c:670
[< inline >] credit_entropy_bits_safe drivers/char/random.c:734
[<ffffffff8328785d>] random_ioctl+0x21d/0x250 drivers/char/random.c:1546
[< inline >] vfs_ioctl fs/ioctl.c:43
[<ffffffff8185316c>] do_vfs_ioctl+0x18c/0xff0 fs/ioctl.c:674
[< inline >] SYSC_ioctl fs/ioctl.c:689
[<ffffffff8185405f>] SyS_ioctl+0x8f/0xc0 fs/ioctl.c:680
[<ffffffff86a995c0>] entry_SYSCALL_64_fastpath+0x23/0xc1
arch/x86/entry/entry_64.S:207
---[ end trace 5d4902b2ba842f1f ]---
This was triggered using the test program:
// autogenerated by syzkaller (http://github.com/google/syzkaller)
int main() {
int fd = open("/dev/random", O_RDWR);
int val = -5000;
ioctl(fd, RNDADDTOENTCNT, &val);
return 0;
}
It's harmless in that (a) only root can trigger it, and (b) after
complaining the code never does let the entropy count go negative, but
it's better to simply not allow this userspace from passing in a
negative entropy value altogether.
Google-Bug-Id: #29575089
Reported-By: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f626300a3e ]
tcp_select_initial_window() intends to advertise a window
scaling for the maximum possible window size. To do so,
it considers the maximum of net.ipv4.tcp_rmem[2] and
net.core.rmem_max as the only possible upper-bounds.
However, users with CAP_NET_ADMIN can use SO_RCVBUFFORCE
to set the socket's receive buffer size to values
larger than net.ipv4.tcp_rmem[2] and net.core.rmem_max.
Thus, SO_RCVBUFFORCE is effectively ignored by
tcp_select_initial_window().
To fix this, consider the maximum of net.ipv4.tcp_rmem[2],
net.core.rmem_max and socket's initial buffer space.
Fixes: b0573dea1f ("[NET]: Introduce SO_{SND,RCV}BUFFORCE socket options")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Suggested-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3a3b62601 ]
macsec_decrypt() is not called when validation is disabled and so
macsec_skb_cb(skb)->rx_sa is not set; but it is used later in
macsec_post_decrypt(), ensure that it's always initialized.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5fc382d875 ]
I was seeing a lot of these:
BUG: sleeping function called from invalid context at mm/slab.h:388
in_atomic(): 0, irqs_disabled(): 0, pid: 14971, name: trinity-c2
Preemption disabled at:[<ffffffff819bcd46>] rhashtable_walk_start+0x46/0x150
[<ffffffff81149abb>] preempt_count_add+0x1fb/0x280
[<ffffffff83295722>] _raw_spin_lock+0x12/0x40
[<ffffffff811aac87>] console_unlock+0x2f7/0x930
[<ffffffff811ab5bb>] vprintk_emit+0x2fb/0x520
[<ffffffff811aba6a>] vprintk_default+0x1a/0x20
[<ffffffff812c171a>] printk+0x94/0xb0
[<ffffffff811d6ed0>] print_stack_trace+0xe0/0x170
[<ffffffff8115835e>] ___might_sleep+0x3be/0x460
[<ffffffff81158490>] __might_sleep+0x90/0x1a0
[<ffffffff8139b823>] kmem_cache_alloc+0x153/0x1e0
[<ffffffff819bca1e>] rhashtable_walk_init+0xfe/0x2d0
[<ffffffff82ec64de>] sctp_transport_walk_start+0x1e/0x60
[<ffffffff82edd8ad>] sctp_transport_seq_start+0x4d/0x150
[<ffffffff8143a82b>] seq_read+0x27b/0x1180
[<ffffffff814f97fc>] proc_reg_read+0xbc/0x180
[<ffffffff813d471b>] __vfs_read+0xdb/0x610
[<ffffffff813d4d3a>] vfs_read+0xea/0x2d0
[<ffffffff813d615b>] SyS_pread64+0x11b/0x150
[<ffffffff8100334c>] do_syscall_64+0x19c/0x410
[<ffffffff832960a5>] return_from_SYSCALL_64+0x0/0x6a
[<ffffffffffffffff>] 0xffffffffffffffff
Apparently we always need to call rhashtable_walk_stop(), even when
rhashtable_walk_start() fails:
* rhashtable_walk_start - Start a hash table walk
* @iter: Hash table iterator
*
* Start a hash table walk. Note that we take the RCU lock in all
* cases including when we return an error. So you must always call
* rhashtable_walk_stop to clean up.
otherwise we never call rcu_read_unlock() and we get the splat above.
Fixes: 53fa1036 ("sctp: fix some rhashtable functions using in sctp proc/diag")
See-also: 53fa1036 ("sctp: fix some rhashtable functions using in sctp proc/diag")
See-also: f2dba9c6 ("rhashtable: Introduce rhashtable_walk_*")
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: stable@vger.kernel.org
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea06f71764 ]
Default kernel behavior is to delete IPv6 addresses on link
down, which entails deletion of the multicast and the
subnet-router anycast addresses. These deletions do not
happen with sysctl setting to keep global IPv6 addresses on
link down, so every link down/up causes an increment of the
anycast and multicast refcounts. These bogus refcounts may
stop these addrs from being removed on subsequent calls to
delete them. The solution is to leave the groups for the
multicast and subnet anycast on link down for the callflow
when global IPv6 addresses are kept.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: Mike Manning <mmanning@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit baedbe5588 ]
Commit 8626c56c82 ("bridge: fix potential use-after-free when hook
returns QUEUE or STOLEN verdict") caused LLDP packets arriving through a
bridge port to be re-injected to the Rx path with skb->dev set to the
bridge device, but this breaks the lldpad daemon.
The lldpad daemon opens a packet socket with protocol set to ETH_P_LLDP
for any valid device on the system, which doesn't not include soft
devices such as bridge and VLAN.
Since packet sockets (ptype_base) are processed in the Rx path after the
Rx handler, LLDP packets with skb->dev set to the bridge device never
reach the lldpad daemon.
Fix this by making the bridge's Rx handler re-inject LLDP packets with
RX_HANDLER_PASS, which effectively restores the behaviour prior to the
mentioned commit.
This means netfilter will never receive LLDP packets coming through a
bridge port, as I don't see a way in which we can have okfn() consume
the packet without breaking existing behaviour. I've already carried out
a similar fix for STP packets in commit 56fae404fb ("bridge: Fix
incorrect re-injection of STP packets").
Fixes: 8626c56c82 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1533e77315 ]
When using an IPoIB bond currently only active-backup mode is a valid
use case and this commit strengthens it.
Since commit 2ab82852a2 ("net/bonding: Enable bonding to enslave
netdevices not supporting set_mac_address()") was introduced till
4.7-rc1, IPoIB didn't support the set_mac_address ndo, and hence the
fail over mac policy always applied to IPoIB bonds.
With the introduction of commit 492a7e67ff ("IB/IPoIB: Allow setting
the device address"), that doesn't hold and practically IPoIB bonds are
broken as of that. To fix it, lets go to fail over mac if the device
doesn't support the ndo OR this is IPoIB device.
As a by-product, this commit also prevents a stack corruption which
occurred when trying to copy 20 bytes (IPoIB) device address
to a sockaddr struct that has only 16 bytes of storage.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba66bbe548 ]
After a612769774 ("udp: prevent bugcheck if filter truncates packet
too much"), there followed various other fixes for similar cases such
as f4979fcea7 ("rose: limit sk_filter trim to payload").
Latter introduced a new helper sk_filter_trim_cap(), where we can pass
the trim limit directly to the socket filter handling. Make use of it
here as well with sizeof(struct udphdr) as lower cap limit and drop the
extra skb->len test in UDP's input path.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1892c3776 upstream.
file_remove_privs() is called with inode lock on file_inode(), which
proceeds to calling notify_change() on file->f_path.dentry. Which triggers
the WARN_ON_ONCE(!inode_is_locked(inode)) in addition to deadlocking later
when ovl_setattr tries to lock the underlying inode again.
Fix this mess by not mixing the layers, but doing everything on underlying
dentry/inode.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 07a2daab49 ("ovl: Copy up underlying inode's ->i_mode to overlay inode")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10eec60ce7 upstream.
This prevents a double-fetch from user space that can lead to to an
undersized allocation and heap overflow.
Fixes: 54dbc15172 ("vfs: hoist the btrfs deduplication ioctl to the vfs")
Signed-off-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bc9491645 upstream.
Although the extent tree depth of 5 should enough be for the worst
case of 2*32 extents of length 1, the extent tree code does not
currently to merge nodes which are less than half-full with a sibling
node, or to shrink the tree depth if possible. So it's possible, at
least in theory, for the tree depth to be greater than 5. However,
even in the worst case, a tree depth of 32 is highly unlikely, and if
the file system is maliciously corrupted, an insanely large eh_depth
can cause memory allocation failures that will trigger kernel warnings
(here, eh_depth = 65280):
JBD2: ext4.exe wants too many credits credits:195849 rsv_credits:0 max:256
------------[ cut here ]------------
WARNING: CPU: 0 PID: 50 at fs/jbd2/transaction.c:293 start_this_handle+0x569/0x580
CPU: 0 PID: 50 Comm: ext4.exe Not tainted 4.7.0-rc5+ #508
Stack:
604a8947 625badd8 0002fd09 00000000
60078643 00000000 62623910 601bf9bc
62623970 6002fc84 626239b0 900000125
Call Trace:
[<6001c2dc>] show_stack+0xdc/0x1a0
[<601bf9bc>] dump_stack+0x2a/0x2e
[<6002fc84>] __warn+0x114/0x140
[<6002fdff>] warn_slowpath_null+0x1f/0x30
[<60165829>] start_this_handle+0x569/0x580
[<60165d4e>] jbd2__journal_start+0x11e/0x220
[<60146690>] __ext4_journal_start_sb+0x60/0xa0
[<60120a81>] ext4_truncate+0x131/0x3a0
[<60123677>] ext4_setattr+0x757/0x840
[<600d5d0f>] notify_change+0x16f/0x2a0
[<600b2b16>] do_truncate+0x76/0xc0
[<600c3e56>] path_openat+0x806/0x1300
[<600c55c9>] do_filp_open+0x89/0xf0
[<600b4074>] do_sys_open+0x134/0x1e0
[<600b4140>] SyS_open+0x20/0x30
[<6001ea68>] handle_syscall+0x88/0x90
[<600295fd>] userspace+0x3fd/0x500
[<6001ac55>] fork_handler+0x85/0x90
---[ end trace 08b0b88b6387a244 ]---
[ Commit message modified and the extent tree depath check changed
from 5 to 32 -- tytso ]
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-16 09:34:57 +02:00
234 changed files with 2332 additions and 1225 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
Greg Kroah-Hartman