commit f436b2ac90 upstream.
The Performance Monitors extension is an optional feature of the
AArch64 architecture, therefore, in order to access Performance
Monitors registers safely, the kernel should detect the architected
PMU unit presence through the ID_AA64DFR0_EL1 register PMUVer field
before accessing them.
This patch implements a guard by reading the ID_AA64DFR0_EL1 register
PMUVer field to detect the architected PMU presence and prevent accessing
PMU system registers if the Performance Monitors extension is not
implemented in the core.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Fixes: 60792ad349 ("arm64: kernel: enforce pmuserenr_el0 initialization and restore")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60792ad349 upstream.
The pmuserenr_el0 register value is architecturally UNKNOWN on reset.
Current kernel code resets that register value iff the core pmu device is
correctly probed in the kernel. On platforms with missing DT pmu nodes (or
disabled perf events in the kernel), the pmu is not probed, therefore the
pmuserenr_el0 register is not reset in the kernel, which means that its
value retains the reset value that is architecturally UNKNOWN (system
may run with eg pmuserenr_el0 == 0x1, which means that PMU counters access
is available at EL0, which must be disallowed).
This patch adds code that resets pmuserenr_el0 on cold boot and restores
it on core resume from shutdown, so that the pmuserenr_el0 setup is
always enforced in the kernel.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32d6397805 upstream.
In paging_init, we allocate the zero page, memset it to zero and then
point TTBR0 to it in order to avoid speculative fetches through the
identity mapping.
In order to guarantee that the freshly zeroed page is indeed visible to
the page table walker, we need to execute a dsb instruction prior to
writing the TTBR.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5db4fd8c52 upstream.
Make sure to clear out any ptrace singlestep state when a ptrace(2)
PTRACE_DETACH call is made on arm64 systems.
Otherwise, the previously ptraced task will die off with a SIGTRAP
signal if the debugger just previously singlestepped the ptraced task.
Signed-off-by: John Blackwood <john.blackwood@ccur.com>
[will: added comment to justify why this is in the arch code]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a61674bdfc upstream.
GCC 6 will include changes to generated code with -mcmodel=large,
which is used to build kernel modules on powerpc64le. This was
necessary because the large model is supposed to allow arbitrary
sizes and locations of the code and data sections, but the ELFv2
global entry point prolog still made the unconditional assumption
that the TOC associated with any particular function can be found
within 2 GB of the function entry point:
func:
addis r2,r12,(.TOC.-func)@ha
addi r2,r2,(.TOC.-func)@l
.localentry func, .-func
To remove this assumption, GCC will now generate instead this global
entry point prolog sequence when using -mcmodel=large:
.quad .TOC.-func
func:
.reloc ., R_PPC64_ENTRY
ld r2, -8(r12)
add r2, r2, r12
.localentry func, .-func
The new .reloc triggers an optimization in the linker that will
replace this new prolog with the original code (see above) if the
linker determines that the distance between .TOC. and func is in
range after all.
Since this new relocation is now present in module object files,
the kernel module loader is required to handle them too. This
patch adds support for the new relocation and implements the
same optimization done by the GNU linker.
Signed-off-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e50c4bef7 upstream.
If a text section starts out with a data blob before the first
function start label, disassembly parsing doing in recordmcount.pl
gets confused on powerpc, leading to creation of corrupted module
objects.
This was not a problem so far since the compiler would never create
such text sections. However, this has changed with a recent change
in GCC 6 to support distances of > 2GB between a function and its
assoicated TOC in the ELFv2 ABI, exposing this problem.
There is already code in recordmcount.pl to handle such data blobs
on the sparc64 platform. This patch uses the same method to handle
those on powerpc as well.
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81d7a3294d upstream.
According to memory-barriers.txt, xchg*, cmpxchg* and their atomic_
versions all need to be fully ordered, however they are now just
RELEASE+ACQUIRE, which are not fully ordered.
So also replace PPC_RELEASE_BARRIER and PPC_ACQUIRE_BARRIER with
PPC_ATOMIC_ENTRY_BARRIER and PPC_ATOMIC_EXIT_BARRIER in
__{cmp,}xchg_{u32,u64} respectively to guarantee fully ordered semantics
of atomic{,64}_{cmp,}xchg() and {cmp,}xchg(), as a complement of commit
b97021f855 ("powerpc: Fix atomic_xxx_return barrier semantics")
This patch depends on patch "powerpc: Make value-returning atomics fully
ordered" for PPC_ATOMIC_ENTRY_BARRIER definition.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49e9cf3f0c upstream.
According to memory-barriers.txt:
> Any atomic operation that modifies some state in memory and returns
> information about the state (old or new) implies an SMP-conditional
> general memory barrier (smp_mb()) on each side of the actual
> operation ...
Which mean these operations should be fully ordered. However on PPC,
PPC_ATOMIC_ENTRY_BARRIER is the barrier before the actual operation,
which is currently "lwsync" if SMP=y. The leading "lwsync" can not
guarantee fully ordered atomics, according to Paul Mckenney:
https://lkml.org/lkml/2015/10/14/970
To fix this, we define PPC_ATOMIC_ENTRY_BARRIER as "sync" to guarantee
the fully-ordered semantics.
This also makes futex atomics fully ordered, which can avoid possible
memory ordering problems if userspace code relies on futex system call
for fully ordered semantics.
Fixes: b97021f855 ("powerpc: Fix atomic_xxx_return barrier semantics")
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f821fc9c7 upstream.
Currently we can hit a scenario where we'll tm_reclaim() twice. This
results in a TM bad thing exception because the second reclaim occurs
when not in suspend mode.
The scenario in which this can happen is the following. We attempt to
deliver a signal to userspace. To do this we need obtain the stack
pointer to write the signal context. To get this stack pointer we
must tm_reclaim() in case we need to use the checkpointed stack
pointer (see get_tm_stackpointer()). Normally we'd then return
directly to userspace to deliver the signal without going through
__switch_to().
Unfortunatley, if at this point we get an error (such as a bad
userspace stack pointer), we need to exit the process. The exit will
result in a __switch_to(). __switch_to() will attempt to save the
process state which results in another tm_reclaim(). This
tm_reclaim() now causes a TM Bad Thing exception as this state has
already been saved and the processor is no longer in TM suspend mode.
Whee!
This patch checks the state of the MSR to ensure we are TM suspended
before we attempt the tm_reclaim(). If we've already saved the state
away, we should no longer be in TM suspend mode. This has the
additional advantage of checking for a potential TM Bad Thing
exception.
Found using syscall fuzzer.
Fixes: fb09692e71 ("powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 42eff6a617 ]
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_orig_node_free_ref.
Fixes: 72822225bd ("batman-adv: Fix rcu_barrier() miss due to double call_rcu() in TT code")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4d922cfc9 ]
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_hardif_free_ref.
Fixes: 89652331c0 ("batman-adv: split tq information in neigh_node struct")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ae3e1e36e3 ]
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_neigh_ifinfo_free_ref.
Fixes: 89652331c0 ("batman-adv: split tq information in neigh_node struct")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2baa753c27 ]
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_neigh_node_free_ref.
Fixes: 89652331c0 ("batman-adv: split tq information in neigh_node struct")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit deed96605f ]
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_orig_ifinfo_free_ref.
Fixes: 7351a4822d ("batman-adv: split out router from orig_node")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44e8e7e91d ]
The batadv_nc_node_free_ref function uses call_rcu to delay the free of the
batadv_nc_node object until no (already started) rcu_read_lock is enabled
anymore. This makes sure that no context is still trying to access the
object which should be removed. But batadv_nc_node also contains a
reference to orig_node which must be removed.
The reference drop of orig_node was done in the call_rcu function
batadv_nc_node_free_rcu but should actually be done in the
batadv_nc_node_release function to avoid nested call_rcus. This is
important because rcu_barrier (e.g. batadv_softif_free or batadv_exit) will
not detect the inner call_rcu as relevant for its execution. Otherwise this
barrier will most likely be inserted in the queue before the callback of
the first call_rcu was executed. The caller of rcu_barrier will therefore
continue to run before the inner call_rcu callback finished.
Fixes: d56b1705e2 ("batman-adv: network coding - detect coding nodes and remove these after timeout")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63b3992722 ]
The batadv_claim_free_ref function uses call_rcu to delay the free of the
batadv_bla_claim object until no (already started) rcu_read_lock is enabled
anymore. This makes sure that no context is still trying to access the
object which should be removed. But batadv_bla_claim also contains a
reference to backbone_gw which must be removed.
The reference drop of backbone_gw was done in the call_rcu function
batadv_claim_free_rcu but should actually be done in the
batadv_claim_release function to avoid nested call_rcus. This is important
because rcu_barrier (e.g. batadv_softif_free or batadv_exit) will not
detect the inner call_rcu as relevant for its execution. Otherwise this
barrier will most likely be inserted in the queue before the callback of
the first call_rcu was executed. The caller of rcu_barrier will therefore
continue to run before the inner call_rcu callback finished.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 60a6531bfe ]
We can't be within an RCU read-side critical section when deleting
VLANs, as underlying drivers might sleep during the hardware operation.
Therefore, replace the RCU critical section with a mutex. This is
consistent with team_vlan_rx_add_vid.
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b6e26ce89 ]
With several ConnectX-4 cards installed on a server, one may receive
irqn > 255 from the kernel API, which we mistakenly trim to 8bit.
This causes EQ creation failure with the following stack trace:
[<ffffffff812a11f4>] dump_stack+0x48/0x64
[<ffffffff810ace21>] __setup_irq+0x3a1/0x4f0
[<ffffffff810ad7e0>] request_threaded_irq+0x120/0x180
[<ffffffffa0923660>] ? mlx5_eq_int+0x450/0x450 [mlx5_core]
[<ffffffffa0922f64>] mlx5_create_map_eq+0x1e4/0x2b0 [mlx5_core]
[<ffffffffa091de01>] alloc_comp_eqs+0xb1/0x180 [mlx5_core]
[<ffffffffa091ea99>] mlx5_dev_init+0x5e9/0x6e0 [mlx5_core]
[<ffffffffa091ec29>] init_one+0x99/0x1c0 [mlx5_core]
[<ffffffff812e2afc>] local_pci_probe+0x4c/0xa0
Fixing it by changing of the irqn type from u8 to unsigned int to
support values > 255
Fixes: 61d0e73e0a ('net/mlx5_core: Use the the real irqn in eq->irqn')
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 34ae6a1aa0 ]
When a tunnel decapsulates the outer header, it has to comply
with RFC 6080 and eventually propagate CE mark into inner header.
It turns out IP6_ECN_set_ce() does not correctly update skb->csum
for CHECKSUM_COMPLETE packets, triggering infamous "hw csum failure"
messages and stack traces.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 229394e8e6 ]
On ARM64, a BUG() is triggered in the eBPF JIT if a filter with a
constant shift that can't be encoded in the immediate field of the
UBFM/SBFM instructions is passed to the JIT. Since these shifts
amounts, which are negative or >= regsize, are invalid, reject them in
the eBPF verifier and the classic BPF filter checker, for all
architectures.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7aaed57c5c ]
Ivaylo Dimitrov reported a regression caused by commit 7866a62104
("dev: add per net_device packet type chains").
skb->dev becomes NULL and we crash in __netif_receive_skb_core().
Before above commit, different kind of bugs or corruptions could happen
without major crash.
But the root cause is that phonet_rcv() can queue skb without checking
if skb is shared or not.
Many thanks to Ivaylo Dimitrov for his help, diagnosis and tests.
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d461873272 ]
The offset inside the fragment was not used for the dma address and
silent data corruption resulted because TSO makes the checksum match.
Fixes: 077742dac2 ("dwc_eth_qos: Add support for Synopsys DWC Ethernet QoS")
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03d84a5f83 ]
Commit 1f718f0f4f ("bonding: populate neighbour's private on enslave")
undoes the fix provided by commit c2edacf80e ("bonding / ipv6: no addrconf
for slaves separately from master") by effectively setting the slave flag
after the slave has been opened. If the slave comes up quickly enough, it
will go through the IPv6 addrconf before the slave flag has been set and
will get a link local IPv6 address.
In order to ensure that addrconf knows to ignore the slave devices on state
change, set IFF_SLAVE before dev_open() during bonding enslavement.
Fixes: 1f718f0f4f ("bonding: populate neighbour's private on enslave")
Signed-off-by: Karl Heiss <kheiss@gmail.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9207f9d45b ]
Skb_gso_segment() uses skb control block during segmentation.
This patch adds 32-bytes room for previous control block which
will be copied into all resulting segments.
This patch fixes kernel crash during fragmenting forwarded packets.
Fragmentation requires valid IP CB in skb for clearing ip options.
Also patch removes custom save/restore in ovs code, now it's redundant.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Link: http://lkml.kernel.org/r/CALYGNiP-0MZ-FExV2HutTvE9U-QQtkKSoE--KN=JQE5STYsjAA@mail.gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 40ba330227 ]
Commit acf8dd0a9d ("udp: only allow UFO for packets from SOCK_DGRAM
sockets") disallows UFO for packets sent from raw sockets. We need to do
the same also for SOCK_DGRAM sockets with SO_NO_CHECK options, even if
for a bit different reason: while such socket would override the
CHECKSUM_PARTIAL set by ip_ufo_append_data(), gso_size is still set and
bad offloading flags warning is triggered in __skb_gso_segment().
In the IPv6 case, SO_NO_CHECK option is ignored but we need to disallow
UFO for packets sent by sockets with UDP_NO_CHECK6_TX option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Tested-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3de03596df ]
Fix possible null pointer dereference that may occur when calling
skb_reserve() on a null skb.
Fixes: 879c7220e8 ("net: pktgen: Observe needed_headroom of the device")
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83d15e70c4 ]
For tcp_yeah, use an ssthresh floor of 2, the same floor used by Reno
and CUBIC, per RFC 5681 (equation 4).
tcp_yeah_ssthresh() was sometimes returning a 0 or negative ssthresh
value if the intended reduction is as big or bigger than the current
cwnd. Congestion control modules should never return a zero or
negative ssthresh. A zero ssthresh generally results in a zero cwnd,
causing the connection to stall. A negative ssthresh value will be
interpreted as a u32 and will set a target cwnd for PRR near 4
billion.
Oleksandr Natalenko reported that a system using tcp_yeah with ECN
could see a warning about a prior_cwnd of 0 in
tcp_cwnd_reduction(). Testing verified that this was due to
tcp_yeah_ssthresh() misbehaving in this way.
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e4006f0b8 ]
When first SYNACK is sent, we already hold rcu_read_lock(), but this
is not true if a SYNACK is retransmitted, as a timer (soft) interrupt
does not hold rcu_read_lock()
Fixes: 45f6fad84c ("ipv6: add complete rcu protection around np->opt")
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 320f1a4a17 ]
proc_dostring() needs an initialized destination string, while the one
provided in proc_sctp_do_hmac_alg() contains stack garbage.
Thus, writing to cookie_hmac_alg would strlen() that garbage and end up
accessing invalid memory.
Fixes: 3c68198e7 ("sctp: Make hmac algorithm selection for cookie generation dynamic")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07b9b37c22 ]
When a vxlan interface is created, the driver checks that there is not
another vxlan interface with the same properties. To do this, it checks
the existing vxlan udp socket. Since commit 1c51a9159d, the creation of
the vxlan socket is done only when the interface is set up, thus it breaks
that test.
Example:
$ ip l a vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip l a vxlan11 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip -br l | grep vxlan
vxlan10 DOWN f2:55:1c:6a:fb:00 <BROADCAST,MULTICAST>
vxlan11 DOWN 7a:cb:b9:38:59:0d <BROADCAST,MULTICAST>
Instead of checking sockets, let's loop over the vxlan iface list.
Fixes: 1c51a9159d ("vxlan: fix race caused by dropping rtnl_unlock")
Reported-by: Thomas Faivre <thomas.faivre@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 712f4aad40 ]
It is possible for a process to allocate and accumulate far more FDs than
the process' limit by sending them over a unix socket then closing them
to keep the process' fd count low.
This change addresses this problem by keeping track of the number of FDs
in flight per user and preventing non-privileged processes from having
more FDs in flight than their configured FD limit.
Reported-by: socketpair@gmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Mitigates: CVE-2013-4312 (Linux 2.0+)
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf5ce5bf3c upstream.
Commit 655fe4effe ("usbcore: add sysfs support to xHCI usb3
hardware LPM") introduced usb3_hardware_lpm sysfs node. This
doesn't show the correct status of USB3 U1 and U2 LPM status.
This patch fixes this by replacing usb3_hardware_lpm with two
nodes, usb3_hardware_lpm_u1 (for U1) and usb3_hardware_lpm_u2
(for U2), and recording the U1/U2 LPM status in right places.
This patch should be back-ported to kernels as old as 4.3,
that contains Commit 655fe4effe ("usbcore: add sysfs support
to xHCI usb3 hardware LPM").
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17bc55864f upstream.
Free skb for received frames with a wrong checksum. This can happen
pretty rapidly, exhausting all memory.
This fixes a memleak (detected with kmemleak). Originally found while
using monitor mode, but it also appears during managed mode (once the
link is up).
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a106804588 upstream.
The detection of direction for compress was only taking into account codec
capabilities and not CPU ones. Fix this by checking the CPU side capabilities
as well
Tested-by: Ashish Panwar <ashish.panwar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24338722cf upstream.
We don't want to use a bypassed write in wm5110_clear_pga_volume,
we might disable the DRE whilst the CODEC is powered down. A
normal regmap_write will always go to the hardware (when not on
cache_only) even if the written value matches the cache. As using
a normal write will still achieve the desired behaviour of bring
the cache and hardware in sync, this patch updates the function
to use a normal write, which avoids issues when the CODEC is
powered down.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 230323dac0 upstream.
Currently ALSA timer device doesn't take the disconnection into
account very well; it merely unlinks the timer device at disconnection
callback but does nothing else. Because of this, when an application
accessing the timer device is disconnected, it may release the
resource before actually closed. In most cases, it results in a
warning message indicating a leftover timer instance like:
ALSA: timer xxxx is busy?
But basically this is an open race.
This patch tries to address it. The strategy is like other ALSA
devices: namely,
- Manage card's refcount at each open/close
- Wake up the pending tasks at disconnection
- Check the shutdown flag appropriately at each possible call
Note that this patch has one ugly hack to handle the wakeup of pending
tasks. It'd be cleaner to introduce a new disconnect op to
snd_timer_instance ops. But since it would lead to internal ABI
breakage and it eventually increase my own work when backporting to
stable kernels, I took a different path to implement locally in
timer.c. A cleanup patch will follow at next for 4.5 kernel.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=109431
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 991f86d7ae upstream.
As HD-audio driver does deferred probe internally via workqueue, the
driver might go into the mixed state doing both probe and remove when
the module gets unloaded during the probe work. This eventually
triggers an Oops, unsurprisingly.
For avoiding this race, we just need to flush the pending probe work
explicitly before actually starting the resource release.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=960710
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bca8e98804 upstream.
When the generic codec driver is specified via model option or such,
the hda driver doesn't try to load the generic driver module but still
loads the codec-specific driver, and this ends up with the binding
failure.
This patch fixes it by moving the generic module request in the common
helper code.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111021
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0bcdbdff3 upstream.
When a TLV ioctl with numid zero is handled, the driver may spew a
kernel warning with a stack trace at each call. The check was
intended obviously only for a kernel driver, but not for a user
interaction. Let's fix it.
This was spotted by syzkaller fuzzer.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ba1fe7a06 upstream.
hrtimer_cancel() waits for the completion from the callback, thus it
must not be called inside the callback itself. This was already a
problem in the past with ALSA hrtimer driver, and the early commit
[fcfdebe707: ALSA: hrtimer - Fix lock-up] tried to address it.
However, the previous fix is still insufficient: it may still cause a
lockup when the ALSA timer instance reprograms itself in its callback.
Then it invokes the start function even in snd_timer_interrupt() that
is called in hrtimer callback itself, results in a CPU stall. This is
no hypothetical problem but actually triggered by syzkaller fuzzer.
This patch tries to fix the issue again. Now we call
hrtimer_try_to_cancel() at both start and stop functions so that it
won't fall into a deadlock, yet giving some chance to cancel the queue
if the functions have been called outside the callback. The proper
hrtimer_cancel() is called in anyway at closing, so this should be
enough.
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43c54b8c7c upstream.
This reverts one hunk of
commit ef44a1ec6e ("ALSA: sound/core: use memdup_user()"), which
replaced a number of kmalloc followed by memcpy with memdup calls.
In this case, we are copying from a struct snd_pcm_hw_params32 to
a struct snd_pcm_hw_params, but the latter is 4 bytes longer than
the 32-bit version, so we need to separate kmalloc and copy calls.
This actually leads to an out-of-bounds memory access later on
in sound/soc/soc-pcm.c:soc_pcm_hw_params() (detected using KASan).
Fixes: ef44a1ec6e ('ALSA: sound/core: use memdup_user()')
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9586495dc3 upstream.
This reverts one hunk of
commit ef44a1ec6e ("ALSA: sound/core: use memdup_user()"), which
replaced a number of kmalloc followed by memcpy with memdup calls.
In this case, we are copying from a struct snd_seq_port_info32 to a
struct snd_seq_port_info, but the latter is 4 bytes longer than the
32-bit version, so we need to separate kmalloc and copy calls.
Fixes: ef44a1ec6e ('ALSA: sound/core: use memdup_user()')
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee8413b010 upstream.
ALSA timer instance object has a couple of linked lists and they are
unlinked unconditionally at snd_timer_stop(). Meanwhile
snd_timer_interrupt() unlinks it, but it calls list_del() which leaves
the element list itself unchanged. This ends up with unlinking twice,
and it was caught by syzkaller fuzzer.
The fix is to use list_del_init() variant properly there, too.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af368027a4 upstream.
ALSA timer ioctls have an open race and this may lead to a
use-after-free of timer instance object. A simplistic fix is to make
each ioctl exclusive. We have already tread_sem for controlling the
tread, and extend this as a global mutex to be applied to each ioctl.
The downside is, of course, the worse concurrency. But these ioctls
aren't to be parallel accessible, in anyway, so it should be fine to
serialize there.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5a663aa42 upstream.
A slave timer instance might be still accessible in a racy way while
operating the master instance as it lacks of locking. Since the
master operation is mostly protected with timer->lock, we should cope
with it while changing the slave instance, too. Also, some linked
lists (active_list and ack_list) of slave instances aren't unlinked
immediately at stopping or closing, and this may lead to unexpected
accesses.
This patch tries to address these issues. It adds spin lock of
timer->lock (either from master or slave, which is equivalent) in a
few places. For avoiding a deadlock, we ensure that the global
slave_active_lock is always locked at first before each timer lock.
Also, ack and active_list of slave instances are properly unlinked at
snd_timer_stop() and snd_timer_close().
Last but not least, remove the superfluous call of _snd_timer_stop()
at removing slave links. This is a noop, and calling it may confuse
readers wrt locking. Further cleanup will follow in a later patch.
Actually we've got reports of use-after-free by syzkaller fuzzer, and
this hopefully fixes these issues.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4a359a004 upstream.
The commit [da6d276957: ALSA: usb-audio: Add resume support for
Native Instruments controls] brought a regression where the Native
Instrument audio devices don't get the correct value at update due to
the missing shift at writing. This patch addresses it.
Fixes: da6d276957 ('ALSA: usb-audio: Add resume support for Native Instruments controls')
Reported-and-tested-by: Owen Williams <owilliams@mixxx.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3567eb6af6 upstream.
ALSA sequencer code has an open race between the timer setup ioctl and
the close of the client. This was triggered by syzkaller fuzzer, and
a use-after-free was caught there as a result.
This patch papers over it by adding a proper queue->timer_mutex lock
around the timer-related calls in the relevant code path.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c06d68bc2 upstream.
ALSA PCM may still have a leftover instance after disconnection and
it delays its release. The problem is that the PCM close code path of
USB-audio driver has a call of snd_usb_autosuspend(). This involves
with the call of usb_autopm_put_interface() and it may lead to a
kernel Oops due to the NULL object like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000190
IP: [<ffffffff815ae7ef>] usb_autopm_put_interface+0xf/0x30 PGD 0
Call Trace:
[<ffffffff8173bd94>] snd_usb_autosuspend+0x14/0x20
[<ffffffff817461bc>] snd_usb_pcm_close.isra.14+0x5c/0x90
[<ffffffff8174621f>] snd_usb_playback_close+0xf/0x20
[<ffffffff816ef58a>] snd_pcm_release_substream.part.36+0x3a/0x90
[<ffffffff816ef6b3>] snd_pcm_release+0xa3/0xb0
[<ffffffff816debb0>] snd_disconnect_release+0xd0/0xe0
[<ffffffff8114d417>] __fput+0x97/0x1d0
[<ffffffff8114d589>] ____fput+0x9/0x10
[<ffffffff8109e452>] task_work_run+0x72/0x90
[<ffffffff81088510>] do_exit+0x280/0xa80
[<ffffffff8108996a>] do_group_exit+0x3a/0xa0
[<ffffffff8109261f>] get_signal+0x1df/0x540
[<ffffffff81040903>] do_signal+0x23/0x620
[<ffffffff8114c128>] ? do_readv_writev+0x128/0x200
[<ffffffff810012e1>] prepare_exit_to_usermode+0x91/0xd0
[<ffffffff810013ba>] syscall_return_slowpath+0x9a/0x120
[<ffffffff817587cd>] ? __sys_recvmsg+0x5d/0x70
[<ffffffff810d2765>] ? ktime_get_ts64+0x45/0xe0
[<ffffffff8115dea0>] ? SyS_poll+0x60/0xf0
[<ffffffff818d2327>] int_ret_from_sys_call+0x25/0x8f
We have already a check of disconnection in snd_usb_autoresume(), but
the check is missing its counterpart. The fix is just to put the same
check in snd_usb_autosuspend(), too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=109431
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 030e2c78d3 upstream.
snd_seq_ioctl_remove_events() calls snd_seq_fifo_clear()
unconditionally even if there is no FIFO assigned, and this leads to
an Oops due to NULL dereference. The fix is just to add a proper NULL
check.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4eae3a506 upstream.
This patch adds native DSD support for the Oppo HA-1. It uses a XMOS chipset
but they use their own vendor ID.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45bdbcfdf2 upstream.
vmx_cpuid_tries to update SECONDARY_VM_EXEC_CONTROL in the VMCS, but
it will cause a vmwrite error on older CPUs because the code does not
check for the presence of CPU_BASED_ACTIVATE_SECONDARY_CONTROLS.
This will get rid of the following trace on e.g. Core2 6600:
vmwrite error: reg 401e value 10 (err 12)
Call Trace:
[<ffffffff8116e2b9>] dump_stack+0x40/0x57
[<ffffffffa020b88d>] vmx_cpuid_update+0x5d/0x150 [kvm_intel]
[<ffffffffa01d8fdc>] kvm_vcpu_ioctl_set_cpuid2+0x4c/0x70 [kvm]
[<ffffffffa01b8363>] kvm_arch_vcpu_ioctl+0x903/0xfa0 [kvm]
Fixes: feda805fe7
Reported-by: Zdenek Kaspar <zkaspar82@gmail.com>
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aba2f06c07 upstream.
Poor #AC was so unimportant until a few days ago that we were
not even tracing its name correctly. But now it's all over
the place.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dbe6cf941 upstream.
If we do not do this, it is not properly saved and restored across
migration. Windows notices due to its self-protection mechanisms,
and is very upset about it (blue screen of death).
Cc: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a1f513776 upstream.
On a cancelled suspend the vcpu_info location does not change (it's
still in the per-cpu area registered by xen_vcpu_setup()). So do not
call xen_hvm_init_shared_info() which would make the kernel think its
back in the shared info. With the wrong vcpu_info, events cannot be
received and the domain will hang after a cancelled suspend.
Signed-off-by: Charles Ouyang <ouyangzhaowei@huawei.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23567fd052 upstream.
This fixes CVE-2016-0728.
If a thread is asked to join as a session keyring the keyring that's already
set as its session, we leak a keyring reference.
This can be tested with the following program:
#include <stddef.h>
#include <stdio.h>
#include <sys/types.h>
#include <keyutils.h>
int main(int argc, const char *argv[])
{
int i = 0;
key_serial_t serial;
serial = keyctl(KEYCTL_JOIN_SESSION_KEYRING,
"leaked-keyring");
if (serial < 0) {
perror("keyctl");
return -1;
}
if (keyctl(KEYCTL_SETPERM, serial,
KEY_POS_ALL | KEY_USR_ALL) < 0) {
perror("keyctl");
return -1;
}
for (i = 0; i < 100; i++) {
serial = keyctl(KEYCTL_JOIN_SESSION_KEYRING,
"leaked-keyring");
if (serial < 0) {
perror("keyctl");
return -1;
}
}
return 0;
}
If, after the program has run, there something like the following line in
/proc/keys:
3f3d898f I--Q--- 100 perm 3f3f0000 0 0 keyring leaked-keyring: empty
with a usage count of 100 * the number of times the program has been run,
then the kernel is malfunctioning. If leaked-keyring has zero usages or
has been garbage collected, then the problem is fixed.
Reported-by: Yevgeny Pats <yevgeny@perception-point.io>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-31 11:28:53 -08:00
80 changed files with 655 additions and 291 deletions
caseUSB_ID(0x20b1,0x300a):/* Matrix Audio Mini-i Pro */
caseUSB_ID(0x22d8,0x0416):/* OPPO HA-1*/
if(fp->altsetting==2)
returnSNDRV_PCM_FMTBIT_DSD_U32_BE;
break;
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
Greg Kroah-Hartman