Reverted upstream by commit 6a22c57b8d
Revert this commit:
commit 2e1c49db4c
Author: Zou Nan hai <nanhai.zou@intel.com>
Date: Fri Jun 1 00:46:28 2007 -0700
x86_64: allocate sparsemem memmap above 4G
This reverts commit 2e1c49db4c.
First off, testing in Fedora has shown it to cause boot failures,
bisected down by Martin Ebourne, and reported by Dave Jobes. So the
commit will likely be reverted in the 2.6.23 stable kernels.
Secondly, in the 2.6.24 model, x86-64 has now grown support for
SPARSEMEM_VMEMMAP, which disables the relevant code anyway, so while the
bug is not visible any more, it's become invisible due to the code just
being irrelevant and no longer enabled on the only architecture that
this ever affected.
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Martin Ebourne <fedora@ebourne.me.uk>
Cc: Zou Nan hai <nanhai.zou@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch edaf420fdc in mainline.
I ran into this problem on a system that was unable to obtain NTP sync
because the clock was running very slow (over 10000ppm slow). ntpd had
declared all of its peers 'reject' with 'peer_dist' reason.
On investigation, the tsc_khz variable was significantly incorrect
causing xtime to run slow. After a reboot tsc_khz was correct so I
did a reboot test to see how often the problem occurred:
Test was done on a 2000 Mhz Xeon system. Of 689 reboots, 8 of them
had unacceptable tsc_khz values (>500ppm):
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 21 3.048%
1999800 - 1999850 166 24.128%
1999850 - 1999900 241 35.029%
1999900 - 1999950 211 30.669%
1999950 - 2000000 42 6.105%
2000000 - 2000000 0 0.000%
2000050 - 2000100 0 0.000%
[...]
2000100 - 2015000 1 0.145% << BAD
2015000 - 2030000 6 0.872% << BAD
2030000 - 2045000 1 0.145% << BAD
2045000 < 0 0.000%
The worst boot was 2032.577 Mhz, over 1.5% off!
It appears that on rare occasions, mach_countup() is taking longer to
complete than necessary.
I suspect that this is caused by the CPU taking a periodic SMI
interrupt right at the end of the 30ms calibration loop. This would
cause the loop to delay while the SMI BIOS hander runs. The resulting
TSC value is beyond what it actually should be resulting in a higher
tsc_khz.
The below patch makes native_calculate_cpu_khz() take the best
(shortest duration, lowest khz) run of it's 3 calibration loops. If a
SMI goes off causing a bad result (long duration, higher khz) it will
be discarded.
With the patch applied, 300 boots of the same system produce good
results:
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 30 10.000%
1999800 - 1999850 166 55.333%
1999850 - 1999900 89 29.667%
1999900 - 1999950 15 5.000%
1999950 < 0 0.000%
Problem was found and tested against 2.6.18. Patch is against 2.6.22.
Signed-off-by: Dave Johnson <djohnson@sw.starentnetworks.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch e6e1ace990 in mainline.
We use signed values for limit checking since the values can go
negative under certain circumstances. However, sizeof() is unsigned
and forces the comparison to be unsigned, so move the comparison into
the heap_free() macros so we can ensure it is a signed comparison.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 6b6815c6d5 in mainline.
Apparently some specific versions of LILO enter the kernel with a
stack pointer that doesn't match the rest of the segments. Make our
best attempt at untangling the resulting mess.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 9a24d04a3c upstream
While we were reviewing pageattr_32/64.c for unification,
Thomas Gleixner noticed the following serious SMP bug in
global_flush_tlb():
down_read(&init_mm.mmap_sem);
list_replace_init(&deferred_pages, &l);
up_read(&init_mm.mmap_sem);
this is SMP-unsafe because list_replace_init() done on two CPUs in
parallel can corrupt the list.
This bug has been introduced about a year ago in the 64-bit tree:
commit ea7322decb
Author: Andi Kleen <ak@suse.de>
Date: Thu Dec 7 02:14:05 2006 +0100
[PATCH] x86-64: Speed and clean up cache flushing in change_page_attr
down_read(&init_mm.mmap_sem);
- dpage = xchg(&deferred_pages, NULL);
+ list_replace_init(&deferred_pages, &l);
up_read(&init_mm.mmap_sem);
the xchg() based version was SMP-safe, but list_replace_init() is not.
So this "cleanup" introduced a nasty bug.
why this bug never become prominent is a mystery - it can probably be
explained with the (still) relative obscurity of the x86_64 architecture.
the safe fix for now is to write-lock init_mm.mmap_sem.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch ace2e92e19 in mainline.
XFS leaves stray mappings around when it vmaps memory to make it
virtually contigious. This upsets Xen if one of those pages is being
recycled into a pagetable, since it finds an extra writable mapping of
the page.
This patch solves the problem in a brute force way, by making XFS
always eagerly unmap its mappings.
[ Stable: This works around a bug in 2.6.23. We may come up with a
better solution for mainline, but this seems like a low-impact fix for
the stable kernel. ]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: XFS masters <xfs-masters@oss.sgi.com>
Cc: Morten =?utf-8?q?B=C3=B8geskov?= <xen-users@morten.bogeskov.dk>
Cc: Mark Williamson <mark.williamson@cl.cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch e3d2697669 in mainline.
The kernel's copy of struct vcpu_register_vcpu_info was out of date,
at best causing the hypercall to fail and the guest kernel to fall
back to the old mechanism, or worse, causing random memory corruption.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Stable Kernel <stable@kernel.org>
Cc: Morten =?utf-8?q?B=C3=B8geskov?= <xen-users@morten.bogeskov.dk>
Cc: Mark Williamson <mark.williamson@cl.cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 9f79991d41 in mainline.
When a pagetable is no longer in use, it must be unpinned so that its
pages can be freed. However, this is only possible if there are no
stray uses of the pagetable. The code currently deals with all the
usual cases, but there's a rare case where a vcpu is changing cr3, but
is doing so lazily, and the change hasn't actually happened by the time
the pagetable is unpinned, even though it appears to have been completed.
This change adds a second per-cpu cr3 variable - xen_current_cr3 -
which tracks the actual state of the vcpu cr3. It is only updated once
the actual hypercall to set cr3 has been completed. Other processors
wishing to unpin a pagetable can check other vcpu's xen_current_cr3
values to see if any cross-cpu IPIs are needed to clean things up.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 91e0c5f3da in mainline.
This adds a mechanism to register a callback function to be called once
a batch of hypercalls has been issued. This is typically used to unlock
things which must remain locked until the hypercall has taken place.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a24864a1d5
uml: definitively kill subprocesses on panic
In a stock 2.6.22.6 kernel, poweroff a user mode linux guest (2.6.22.6 running
in skas0 mode) will halt the host linux. I think the reason is the kernel
thread abort because of a bug. Then the sys_reboot in process of user mode
linux guest is not trapped by the user mode linux kernel and is executed by
host. I think it is better to make sure all of our children process to quit
when user mode linux kernel abort.
[ jdike - the kernel process needs to ignore SIGTERM, plus the waitpid/kill
loop is needed to make sure that all of our children are dead before the
kernel exits ]
Signed-off-by: Lepton Wu <ytht.net@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 189872f968 in mainline.
uml: don't use glibc asm/user.h
Stop including asm/user.h from libc - it seems to be disappearing from
distros. It's replaced with sys/user.h which defines user_fpregs_struct and
user_fpxregs_struct instead of user_i387_struct and struct user_fxsr_struct on
i386.
As a bonus, on x86_64, I get to dump some stupid typedefs which were needed in
order to get asm/user.h to compile.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 818f6ef407 in mainline.
uml: fix an IPV6 libc vs kernel symbol clash
On some systems, with IPV6 configured, there is a clash between the kernel's
in6addr_any and the one in libc.
This is handled in the usual (gross) way of defining the kernel symbol out of
the way on the gcc command line.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 71f926f2ea in mainline.
uml: stop using libc asm/page.h
Remove includes of asm/page.h from libc code. This header seems to be
disappearing, and UML doesn't make much use of it anyway.
The one use, PAGE_SHIFT in stub.h, is handled by copying the constant from the
kernel side of the house in common_offsets.h.
[ jdike - added arch/um/kernel/skas/clone.c for -stable ]
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch db220b234d in mainline.
pci_device_to_OF_node() returns the device node attached to a PCI device,
but doesn't actually grab a reference - we need to do it ourselves.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch ba02946a90 in mainline
Its legal for the stfiwx instruction to have RA = 0 as part of its
effective address calculation. This is illegal for all other XE
form instructions.
Add code to compute the proper effective address for stfiwx if
RA = 0 rather than treating it as illegal.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 572afc248c in mainline.
Tested with Malta; inflates malta_defconfig by 3932 bytes. Ideally there
should be additional configuration to allow getting rid of this overhead
but that would be too much complexity at this stage of the release cycle.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch a76ab5c10d in mainline.
When GDB writes a breakpoint into address area of inferior process the
kernel needs to invalidate the modified memory in the inferior which
is done by calling flush_cache_page which in turns calls
r4k_flush_cache_page and local_r4k_flush_cache_page for VSMP or SMTC
kernel via r4k_on_each_cpu().
As the VSMP and SMTC SMP kernels for 34K are running on a single shared
caches it is possible to get away without interprocessor function calls.
This optimization is implemented in r4k_on_each_cpu, so
local_r4k_flush_cache_page is only ever called on the local CPU.
This is where the following code in local_r4k_flush_cache_page() strikes:
/*
* If ownes no valid ASID yet, cannot possibly have gotten
* this page into the cache.
*/
if (cpu_context(smp_processor_id(), mm) == 0)
return;
On VSMP and SMTC had a function of cpu_context() for each CPU(TC).
So in case another CPU than the CPU executing local_r4k_cache_flush_page
has not accessed the mm but one of the other CPUs has there may be data
to be flushed in the cache yet local_r4k_cache_flush_page will falsely
return leaving the I-cache inconsistent for the breakpoint.
While the issue was discovered with GDB it also exists in
local_r4k_flush_cache_range() and local_r4k_flush_cache().
Fixed by introducing a new function has_valid_asid which on MT kernels
returns true if a mm is active on any processor in the system.
This is relativly expensive since for memory acccesses in that loop
cache misses have to be assumed but it seems the most viable solution
for 2.6.23 and older -stable kernels.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch d58aa8c7b1 in mainline.
From: Chris Wright <chrisw@sous-sol.org>
Date: Tue, 23 Oct 2007 20:36:14 -0700
Subject: [PATCH] [SPARC64]: pass correct addr in get_fb_unmapped_area(MAP_FIXED)
Looks like the MAP_FIXED case is using the wrong address hint. I'd
expect the comment "don't mess with it" means pass the request
straight on through, not change the address requested to -ENOMEM.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch d060db63fd in mainline.
[SPARC64]: Fix register usage in xor_raid_4().
Some typos led to using %i6/%i7 instead of %l6/%l7 in loads which is
really really bad because those are the frame pointer and return PC.
Based upon a raid5 crash report by Bertrand Joel.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 6eca9004df in mainline.
For the locking to work, only the tag map and tag bit map may be shared
(incidentally, I was just explaining this to Nick yesterday, but I
apparently didn't review the code well enough myself). But we also share
the busy list! The busy_list must be queue private, or we need a
block_queue_tag covering lock as well.
So we have to move the busy_list to the queue. This'll work fine, and
it'll actually also fix a problem with blk_queue_invalidate_tags() which
will invalidate tags across all shared queues. This is a bit confusing,
the low level driver should call it for each queue seperately since
otherwise you cannot kill tags on just a single queue for eg a hard
drive that stops responding. Since the function has no callers
currently, it's not an issue.
This is fixed with commit 6eca9004df in
Linus' tree.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 487e9bf25c in mainline.
It's possible to provoke unionfs (not yet in mainline, though in mm and
some distros) to hit shmem_writepage's BUG_ON(page_mapped(page)). I expect
it's possible to provoke the 2.6.23 ecryptfs in the same way (but the
2.6.24 ecryptfs no longer calls lower level's ->writepage).
This came to light with the recent find that AOP_WRITEPAGE_ACTIVATE could
leak from tmpfs via write_cache_pages and unionfs to userspace. There's
already a fix (e423003028 - writeback: don't
propagate AOP_WRITEPAGE_ACTIVATE) in the tree for that, and it's okay so
far as it goes; but insufficient because it doesn't address the underlying
issue, that shmem_writepage expects to be called only by vmscan (relying on
backing_dev_info capabilities to prevent the normal writeback path from
ever approaching it).
That's an increasingly fragile assumption, and ramdisk_writepage (the other
source of AOP_WRITEPAGE_ACTIVATEs) is already careful to check
wbc->for_reclaim before returning it. Make the same check in
shmem_writepage, thereby sidestepping the page_mapped BUG also.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Erez Zadok <ezk@cs.sunysb.edu>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[FUTEX]: Fix address computation in compat code.
[ Upstream commit: 3c5fd9c77d ]
compat_exit_robust_list() computes a pointer to the
futex entry in userspace as follows:
(void __user *)entry + futex_offset
'entry' is a 'struct robust_list __user *', and
'futex_offset' is a 'compat_long_t' (typically a 's32').
Things explode if the 32-bit sign bit is set in futex_offset.
Type promotion sign extends futex_offset to a 64-bit value before
adding it to 'entry'.
This triggered a problem on sparc64 running 32-bit applications which
would lock up a cpu looping forever in the fault handling for the
userspace load in handle_futex_death().
Compat userspace runs with address masking (wherein the cpu zeros out
the top 32-bits of every effective address given to a memory operation
instruction) so the sparc64 fault handler accounts for this by
zero'ing out the top 32-bits of the fault address too.
Since the kernel properly uses the compat_uptr interfaces, kernel side
accesses to compat userspace work too since they will only use
addresses with the top 32-bit clear.
Because of this compat futex layer bug we get into the following loop
when executing the get_user() load near the top of handle_futex_death():
1) load from address '0xfffffffff7f16bd8', FAULT
2) fault handler clears upper 32-bits, processes fault
for address '0xf7f16bd8' which succeeds
3) goto #1
I want to thank Bernd Zeimetz, Josip Rodin, and Fabio Massimo Di Nitto
for their tireless efforts helping me track down this bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sched: keep utime/stime monotonic
cpustats use utime/stime as a ratio against sum_exec_runtime, as a
consequence it can happen - when the ratio changes faster than time
accumulates - that either can be appear to go backwards.
Combined backport for 2.6.23 of the following patches from mainline:
commit 73a2bcb0ed
Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
sched: keep utime/stime monotonic
commit 9301899be7
Author: Balbir Singh <balbir@linux.vnet.ibm.com>
sched: fix /proc/<PID>/stat stime/utime monotonicity, part 2
Signed-off-by: Frans Pop <elendil@planet.nl>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch a115d5caca in mainline.
this Xen related commit:
commit 966812dc98
Author: Jeremy Fitzhardinge <jeremy@goop.org>
Date: Tue May 8 00:28:02 2007 -0700
Ignore stolen time in the softlockup watchdog
broke the softlockup watchdog to never report any lockups. (!)
print_timestamp defaults to 0, this makes the following condition
always true:
if (print_timestamp < (touch_timestamp + 1) ||
and we'll in essence never report soft lockups.
apparently the functionality of the soft lockup watchdog was never
actually tested with that patch applied ...
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 05aa345034 in mainline.
SLUB: Fix memory leak by not reusing cpu_slab
Fix the memory leak that may occur when we attempt to reuse a cpu_slab
that was allocated while we reenabled interrupts in order to be able to
grow a slab cache. The per cpu freelist may contain objects and in that
situation we may overwrite the per cpu freelist pointer loosing objects.
This only occurs if we find that the concurrently allocated slab fits
our allocation needs.
If we simply always deactivate the slab then the freelist will be properly
reintegrated and the memory leak will go away.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 3b6662f192 upstream.
Here is another sync patch of Documentation/ja_JP/HOWTO
Japanese developer sent me some cosmetic changes and also follow
changes of HOWTO
Cross reference URL (sosdg.org/qiyong/lxr)
known_regression explanations on kernel dev. process
Signed-off-by: Tsugikazu Shibata <tshibata@ab.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 22800a2830 in mainline.
Commit faf8c714f4 caused a regression:
parameter names longer than MAX_KBUILD_MODNAME will now be rejected,
although we just need to keep the module name part that short. This patch
restores the old behaviour while still avoiding that memchr is called with
its length parameter larger than the total string length.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch faf8c714f4 in mainline.
If memchr argument is longer than strlen(kp->name), there will be some
weird result.
It will casuse duplicate filenames in sysfs for the "nousb". kernel
warning messages are as bellow:
sysfs: duplicate filename 'usbcore' can not be created
WARNING: at fs/sysfs/dir.c:416 sysfs_add_one()
[<c01c4750>] sysfs_add_one+0xa0/0xe0
[<c01c4ab8>] create_dir+0x48/0xb0
[<c01c4b69>] sysfs_create_dir+0x29/0x50
[<c024e0fb>] create_dir+0x1b/0x50
[<c024e3b6>] kobject_add+0x46/0x150
[<c024e2da>] kobject_init+0x3a/0x80
[<c053b880>] kernel_param_sysfs_setup+0x50/0xb0
[<c053b9ce>] param_sysfs_builtin+0xee/0x130
[<c053ba33>] param_sysfs_init+0x23/0x60
[<c024d062>] __next_cpu+0x12/0x20
[<c052aa30>] kernel_init+0x0/0xb0
[<c052aa30>] kernel_init+0x0/0xb0
[<c052a856>] do_initcalls+0x46/0x1e0
[<c01bdb12>] create_proc_entry+0x52/0x90
[<c0158d4c>] register_irq_proc+0x9c/0xc0
[<c01bda94>] proc_mkdir_mode+0x34/0x50
[<c052aa30>] kernel_init+0x0/0xb0
[<c052aa92>] kernel_init+0x62/0xb0
[<c0104f83>] kernel_thread_helper+0x7/0x14
=======================
kobject_add failed for usbcore with -EEXIST, don't try to register things with the same name in the same directory.
[<c024e466>] kobject_add+0xf6/0x150
[<c053b880>] kernel_param_sysfs_setup+0x50/0xb0
[<c053b9ce>] param_sysfs_builtin+0xee/0x130
[<c053ba33>] param_sysfs_init+0x23/0x60
[<c024d062>] __next_cpu+0x12/0x20
[<c052aa30>] kernel_init+0x0/0xb0
[<c052aa30>] kernel_init+0x0/0xb0
[<c052a856>] do_initcalls+0x46/0x1e0
[<c01bdb12>] create_proc_entry+0x52/0x90
[<c0158d4c>] register_irq_proc+0x9c/0xc0
[<c01bda94>] proc_mkdir_mode+0x34/0x50
[<c052aa30>] kernel_init+0x0/0xb0
[<c052aa92>] kernel_init+0x62/0xb0
[<c0104f83>] kernel_thread_helper+0x7/0x14
=======================
Module 'usbcore' failed to be added to sysfs, error number -17
The system will be unstable now.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The kernel has for random historical reasons allowed ptrace() accesses
to access (and insert) pages into the page cache above the size of the
file.
However, Nick broke that by mistake when doing the new fault handling in
commit 54cb8821de ("mm: merge populate and
nopage into fault (fixes nonlinear)". The breakage caused a hang with
gdb when trying to access the invalid page.
The ptrace "feature" really isn't worth resurrecting, since it really is
wrong both from a portability _and_ from an internal page cache validity
standpoint. So this removes those old broken remnants, and fixes the
ptrace() hang in the process.
Noticed and bisected by Duane Griffin, who also supplied a test-case
(quoth Nick: "Well that's probably the best bug report I've ever had,
thanks Duane!").
Cc: Duane Griffin <duaneg@dghda.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 97855b49b6 in mainline.
It's currently possible to send posix_locks_deadlock() into an infinite
loop (under the BKL).
For now, fix this just by bailing out after a few iterations. We may
want to fix this in a way that better clarifies the semantics of
deadlock detection. But that will take more time, and this minimal fix
is probably adequate for any realistic scenario, and is simple enough to
be appropriate for applying to stable kernels now.
Thanks to George Davis for reporting the problem.
Cc: "George G. Davis" <gdavis@mvista.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 3aa416b07f in mainline.
It is possible for the current->curr_chain_key to become inconsistent with the
current index if the chain fails to validate. The end result is that future
lock_acquire() operations may inadvertently fail to find a hit in the cache
resulting in a new node being added to the graph for every acquire.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 6c08772e49 in mainline.
* corruption fix: we only want the lower 16 bits of length (0 == 64kb)
* ditto: the upper layer sets max-phys-segments to LIBATA_MAX_PRD,
so we must reset it to own hw-specific length.
* delete unused mv_fill_sg() return value
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Au1000: set the PCI controller IO base
[MIPS] Alchemy: Fix USB initialization.
[MIPS] IP32: Fix fatal typo in address computation.
The recent fix for a circular lock dependency unfortunately introduced a
potential memory leak in the event where the call to nlmsvc_lookup_host
fails for some reason.
Thanks to Roel Kluin for spotting this.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent mv_fill_sg() rewrite, to fix a data corruption problem
related to IOMMU virtual merging, forgot to account for the
potentially-increased size of the scatter/gather table after its run.
Additionally, the DMA boundary is reduced from 0xffffffff to 0xffff
to more closely match the needs of mv_fill_sg().
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a wrong ifdef in the board setup code, leading to the GPIO
pin not being pulled high, and thus the USB switch not being powered at all.
This finishes the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which
started in 2005 (before 2.6.12-rc2), then probably because things were
working anyway for most people got forgotten.
[Ralf: Paolo's original patch didn't fix the module case, Florian's patch
only fixed MTX1 etc. so this is a combined patch plus some cleanups.]
Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When building a custom keymap, after setting GENERATE_KEYMAP := 1 in
drivers/char/Makefile, the kernel build fails like this:
CC drivers/char/vt.o
make[2]: *** No rule to make target `drivers/char/%.map', needed by `drivers/char/defkeymap.c'. Stop.
make[1]: *** [drivers/char] Error 2
make: *** [drivers] Error 2
This was caused by commit af8b128719, which
deleted a necessary colon from the Makefile rule that generates the keymap,
since that rule contains both a target and a target-pattern. The following
patch puts the colon back:
Signed-off-by: Maarten Bressers <mbres@gentoo.org>
Cc: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix against access random data bytes outside the dev->chanmap array.
Thanks to Oliver Neukum for pointing me to this issue.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When IOCB_FLAG_RESFD flag is set and iocb->aio_resfd is incorrect,
statement 'goto out_put_req' is executed. At label 'out_put_req',
aio_put_req(..) is called, which requires 'req->ki_filp' set.
Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Cc: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Greg Kroah-Hartman