commit 40bf8f162d upstream.
There is no point to enter safe mode during DP/TBT configuration
if the DP/TBT was already configured in mux. This is because safe
mode is only applicable when there is a need to reconfigure the
pins in order to avoid damage within/to port partner.
In some chrome systems, IOM/mux is already configured before OS
comes up. Thus, when driver is probed, it blindly enters safe
mode due to PD negotiations but only after gfx driver lowers
dp_phy_ownership, will the IOM complete safe mode and send an
ack to PMC.
Since, that never happens, we see IPC timeout.
Hence, allow safe mode only when pin reconfiguration is not
required, which makes sense.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Cc: stable <stable@kernel.org>
Signed-off-by: Rajat Khandelwal <rajat.khandelwal@linux.intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221024171611.181468-1-rajat.khandelwal@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d5333c931 upstream.
When usb 3.0 hub connect with one USB 2.0 device and NO USB 3.0 device,
some usb hub reports endless port reset message.
[ 190.324169] usb 2-1: new SuperSpeed USB device number 88 using xhci-hcd
[ 190.352834] hub 2-1:1.0: USB hub found
[ 190.356995] hub 2-1:1.0: 4 ports detected
[ 190.700056] usb 2-1: USB disconnect, device number 88
[ 192.472139] usb 2-1: new SuperSpeed USB device number 89 using xhci-hcd
[ 192.500820] hub 2-1:1.0: USB hub found
[ 192.504977] hub 2-1:1.0: 4 ports detected
[ 192.852066] usb 2-1: USB disconnect, device number 89
The reason is the runtime pm state of USB2.0 port is active and
USB 3.0 port is suspend, so parent device is active state.
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb2/power/runtime_status
suspended
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb1/power/runtime_status
active
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/power/runtime_status
active
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/power/runtime_status
active
So xhci_cdns3_suspend_quirk() have not called. U3 configure is not applied.
move U3 configure into host start. Reinit again in resume function in case
controller power lost during suspend.
Cc: stable@vger.kernel.org 5.10
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221026190749.2280367-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a58b8d602 upstream.
There is a deadlock in ci_otg_del_timer(), the process is
shown below:
(thread 1) | (thread 2)
ci_otg_del_timer() | ci_otg_hrtimer_func()
... |
spin_lock_irqsave() //(1) | ...
... |
hrtimer_cancel() | spin_lock_irqsave() //(2)
(block forever)
We hold ci->lock in position (1) and use hrtimer_cancel() to
wait ci_otg_hrtimer_func() to stop, but ci_otg_hrtimer_func()
also need ci->lock in position (2). As a result, the
hrtimer_cancel() in ci_otg_del_timer() will be blocked forever.
This patch extracts hrtimer_cancel() from the protection of
spin_lock_irqsave() in order that the ci_otg_hrtimer_func()
could obtain the ci->lock.
What`s more, there will be no race happen. Because the
"next_timer" is always under the protection of
spin_lock_irqsave() and we only check whether "next_timer"
equals to NUM_OTG_FSM_TIMERS in the following code.
Fixes: 3a316ec4c9 ("usb: chipidea: use hrtimer for otg fsm timers")
Cc: stable <stable@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220918033312.94348-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1547f12df upstream.
Add LARA-L6 PIDs for three different USB compositions.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In default mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
In CDC-ECM mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
[ johan: drop PID defines in favour of comments ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9e37a5c4d upstream.
The official LARA-R6 (00B) modem uses 0x908b PID. LARA-R6 00B does not
implement a QMI interface on port 4, the reservation (RSVD(4)) has been
added to meet other companies that implement QMI on that interface.
LARA-R6 00B USB composition exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd136706b4 upstream.
What the code does is to not check the return value from
devm_gpiod_get() and then avoid using an erroneous GPIO descriptor
with IS_ERR_OR_NULL().
This will miss real errors from the GPIO core that should not be
ignored, such as probe deferral.
Instead request the GPIO as explicitly optional, which means that
if it doesn't exist, the descriptor returned will be NULL.
Then we can add error handling and also avoid just doing this on
the device tree path, and simplify the site where the optional
GPIO descriptor is used.
There were some problems with cleaning up this GPIO descriptor
use in the past, but this is the proper way to deal with it.
Cc: Rafał Miłecki <rafal@milecki.pl>
Cc: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20221107090753.1404679-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fc801f801 upstream.
This patch fixes a segfault by adding a null check on synth in
speakup_con_update(). The segfault can be reproduced as follows:
- Login into a text console
- Load speakup and speakup_soft modules
- Remove speakup_soft
- Switch to a graphics console
This is caused by lack of a null check on `synth` in
speakup_con_update().
Here's the sequence that causes the segfault:
- When we remove the speakup_soft, synth_release() sets the synth
to null.
- After that, when we change the virtual console to graphics
console, vt_notifier_call() is fired, which then calls
speakup_con_update().
- Inside speakup_con_update() there's no null check on synth,
so it calls synth_printf().
- Inside synth_printf(), synth_buffer_add() and synth_start(),
both access synth, when it is null and causing a segfault.
Therefore adding a null check on synth solves the issue.
Fixes: 2610df4148 ("staging: speakup: Add pause command used on switching to graphical mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Mushahid Hussain <mushi.shar@gmail.com>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20221010165720.397042-1-mushi.shar@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e54fad8044 upstream.
If CONFIG_SLIM_QCOM_NGD_CTRL=y, CONFIG_QCOM_RPROC_COMMON=m, COMPILE_TEST=y,
bulding fails:
drivers/slimbus/qcom-ngd-ctrl.o: In function `qcom_slim_ngd_ctrl_probe':
qcom-ngd-ctrl.c:(.text+0x330): undefined reference to `qcom_register_ssr_notifier'
qcom-ngd-ctrl.c:(.text+0x5fc): undefined reference to `qcom_unregister_ssr_notifier'
drivers/slimbus/qcom-ngd-ctrl.o: In function `qcom_slim_ngd_remove':
qcom-ngd-ctrl.c:(.text+0x90c): undefined reference to `qcom_unregister_ssr_notifier'
Make SLIM_QCOM_NGD_CTRL depends on QCOM_RPROC_COMMON || (COMPILE_TEST && !QCOM_RPROC_COMMON) to fix this.
Fixes: e291691c69 ("slimbus: qcom-ngd-ctrl: allow compile testing without QCOM_RPROC_COMMON")
Cc: stable <stable@kernel.org>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221027095904.3388959-1-zhengbin13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d68cc25b7c upstream.
The change breaks device tree based platforms with PHY device and use
usb-role-switch instead of an extcon switch. extcon_find_edev_by_node()
will return EPROBE_DEFER if it can not find a device so probing without
an extcon device will be deferred indefinitely. Fix this by
explicitly checking for usb-role-switch.
At least the out-of-tree USB3 support on Apple silicon based platforms
using dwc3 with tipd USB Type-C and PD controller is affected by this
issue.
Fixes: d182c2e1bc ("usb: dwc3: Don't switch OTG -> peripheral if extcon is present")
Cc: stable@kernel.org
Signed-off-by: Janne Grunau <j@jannau.net>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20221106214804.2814-1-j@jannau.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c294de36e upstream.
This reverts commit 6000b8d900.
The offending commit disabled the USB core PHY management as the dwc3
already manages the PHYs in question.
Unfortunately some platforms have started relying on having USB core
also controlling the PHY and this is specifically currently needed on
some Exynos platforms for PHY calibration or connected device may fail
to enumerate.
The PHY calibration was previously handled in the dwc3 driver, but to
work around some issues related to how the dwc3 driver interacts with
xhci (e.g. using multiple drivers) this was moved to USB core by commits
34c7ed72f4 ("usb: core: phy: add support for PHY calibration") and
a0a465569b ("usb: dwc3: remove generic PHY calibrate() calls").
The same PHY obviously should not be controlled from two different
places, which for example do no agree on the PHY mode or power state
during suspend, but as the offending patch was backported to stable,
let's revert it for now.
Reported-by: Stefan Agner <stefan@agner.ch>
Link: https://lore.kernel.org/lkml/808bdba846bb60456adf10a3016911ee@agner.ch/
Fixes: 6000b8d900 ("usb: dwc3: disable USB core PHY management")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20221103144648.14197-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e444a4de6 upstream.
DM maps DRM CRTC degamma to DPP (pre-blending) degamma block, but DCE doesn't
support programmable degamma curve anywhere. Currently, a custom degamma is
accepted by DM but just ignored by DCE driver and degamma correction isn't
actually applied. There is no way to map custom degamma in DCE, therefore, DRM
CRTC degamma property shouldn't be enabled for DCE drivers.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7e4f77c99 upstream.
[Why]
dcn314 uses optc2_configure_crc() that wraps
optc1_configure_crc() + set additional registers
not applicable to dcn314.
It's not critical but when used leads to warning like:
WARNING: drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c
Call Trace:
<TASK>
generic_reg_set_ex+0x6d/0xe0 [amdgpu]
optc2_configure_crc+0x60/0x80 [amdgpu]
dc_stream_configure_crc+0x129/0x150 [amdgpu]
amdgpu_dm_crtc_configure_crc_source+0x5d/0xe0 [amdgpu]
[How]
Use optc1_configure_crc() directly
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d502ef889 upstream.
[Why]
Since introduction of patch "Query DPIA HPD status.", link detection at
boot could be accessing DPIA AUX, which will not succeed until
DMUB outbox messaging is enabled and results in below dmesg logs:
[ 160.840227] [drm:amdgpu_dm_process_dmub_aux_transfer_sync [amdgpu]] *ERROR* wait_for_completion_timeout timeout!
[How]
Enable DMUB outbox messaging before link detection at boot time.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7af87fc1ba upstream.
On IGT, there is a test named amd_hotplug, and when the subtest basic is
executed on DCN31, we get the following error:
[drm] *ERROR* [CRTC:71:crtc-0] flip_done timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CRTC:71:crtc-0] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CONNECTOR:88:DP-1] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [PLANE:59:plane-3] commit wait timed out
After enable the page flip log with the below command:
echo -n 'format "[PFLIP]" +p' > /sys/kernel/debug/dynamic_debug/control
It is possible to see that the flip was submitted, but DC never replied
back, which generates time-out issues. This is an indication that the
HUBP surface flip is missing. This commit fixes this issue by adding
hubp1_set_flip_int to DCN31.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d8494c346 upstream.
[Why]
Some DPIA AUX replies have incorrect data length from original request.
This could lead to overwriting of destination buffer if reply length is
larger, which could cause invalid access to stack since many destination
buffers are declared as local variables.
[How]
Check for invalid length from DPIA AUX replies and trigger a retry if
reply length is not the same as original request. A DRM_WARN() dmesg log
is also produced.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5954acbacb upstream.
Current dual mode adaptor ("DP++") detection code assumes that all
adaptors support i2c sub-addressing for read operations from the
DP-HDMI adaptor ID buffer. It has been observed that multiple
adaptors do not in fact support this, and always return data starting
at register 0. On affected adaptors, the code fails to read the proper
registers that would identify the device as a type 2 adaptor, and
handles those as type 1, limiting the TMDS clock to 165MHz, even if
the according register would announce a higher TMDS clock.
Fix this by always reading the ID buffer starting from offset 0, and
discarding any bytes before the actual offset of interest.
We tried finding authoritative documentation on whether or not this is
allowed behaviour, but since all the official VESA docs are paywalled,
the best we could come up with was the spec sheet for Texas Instruments'
SNx5DP149 chip family.[1] It explicitly mentions that sub-addressing is
supported for register writes, but *not* for reads (See NOTE in
section 8.5.3). Unless TI openly decided to violate the VESA spec, one
could take that as a hint that sub-addressing is in fact not mandated
by VESA.
The other two adaptors affected used the PS8409(A) and the LT8611,
according to the data returned from their ID buffers.
[1] https://www.ti.com/lit/ds/symlink/sn75dp149.pdf
Cc: stable@vger.kernel.org
Signed-off-by: Simon Rettberg <simon.rettberg@rz.uni-freiburg.de>
Reviewed-by: Rafael Gieschke <rafael.gieschke@rz.uni-freiburg.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221006113314.41101987@computer
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42fb0a1e84 upstream.
Currently the way polling works on the ring buffer is broken. It will
return immediately if there's any data in the ring buffer whereas a read
will block until the watermark (defined by the tracefs buffer_percent file)
is hit.
That is, a select() or poll() will return as if there's data available,
but then the following read will block. This is broken for the way
select()s and poll()s are supposed to work.
Have the polling on the ring buffer also block the same way reads and
splice does on the ring buffer.
Link: https://lkml.kernel.org/r/20221020231427.41be3f26@gandalf.local.home
Cc: Linux Trace Kernel <linux-trace-kernel@vger.kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Primiano Tucci <primiano@google.com>
Cc: stable@vger.kernel.org
Fixes: 1e0d6714ac ("ring-buffer: Do not wake up a splice waiter when page is not full")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19ba6c8af9 upstream.
The @ftrace_mod is allocated by kzalloc(), so both the members {prev,next}
of @ftrace_mode->list are NULL, it's not a valid state to call list_del().
If kstrdup() for @ftrace_mod->{func|module} fails, it goes to @out_free
tag and calls free_ftrace_mod() to destroy @ftrace_mod, then list_del()
will write prev->next and next->prev, where null pointer dereference
happens.
BUG: kernel NULL pointer dereference, address: 0000000000000008
Oops: 0002 [#1] PREEMPT SMP NOPTI
Call Trace:
<TASK>
ftrace_mod_callback+0x20d/0x220
? do_filp_open+0xd9/0x140
ftrace_process_regex.isra.51+0xbf/0x130
ftrace_regex_write.isra.52.part.53+0x6e/0x90
vfs_write+0xee/0x3a0
? __audit_filter_op+0xb1/0x100
? auditd_test_task+0x38/0x50
ksys_write+0xa5/0xe0
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Kernel panic - not syncing: Fatal exception
So call INIT_LIST_HEAD() to initialize the list member to fix this issue.
Link: https://lkml.kernel.org/r/20221116015207.30858-1-xiujianfeng@huawei.com
Cc: stable@vger.kernel.org
Fixes: 673feb9d76 ("ftrace: Add :mod: caching infrastructure to trace_array")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c964d62f5c ]
Device mappers had always been getting the default 511 dma mask, but
the underlying device might have a larger alignment requirement. Since
this value is used to determine alloweable direct-io alignment, this
needs to be a stackable limit.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20221110184501.2451620-2-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 86e4d3e8d1 ("dm-crypt: provide dma_alignment limit in io_hints")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sven Peter