Currently, the MT753X switches treat frames with :01-0D and :0F MAC DAs as
regular multicast frames, therefore flooding them to user ports.
On page 205, section "8.6.3 Frame filtering" of the active standard, IEEE
Std 802.1Q™-2022, it is stated that frames with 01:80:C2:00:00:00-0F as MAC
DA must only be propagated to C-VLAN and MAC Bridge components. That means
VLAN-aware and VLAN-unaware bridges. On the switch designs with CPU ports,
these frames are supposed to be processed by the CPU (software). So we make
the switch only forward them to the CPU port. And if received from a CPU
port, forward to a single port. The software is responsible of making the
switch conform to the latter by setting a single port as destination port
on the special tag.
This switch intellectual property cannot conform to this part of the
standard fully. Whilst the REV_UN frame tag covers the remaining :04-0D and
:0F MAC DAs, it also includes :22-FF which the scope of propagation is not
supposed to be restricted for these MAC DAs.
Set frames with :01-03 MAC DAs to be trapped to the CPU port(s). Add a
comment for the remaining MAC DAs.
Note that the ingress port must have a PVID assigned to it for the switch
to forward untagged frames. A PVID is set by default on VLAN-aware and
VLAN-unaware ports. However, when the network interface that pertains to
the ingress port is attached to a vlan_filtering enabled bridge, the user
can remove the PVID assignment from it which would prevent the link-local
frames from being trapped to the CPU port. I am yet to see a way to forward
link-local frames while preventing other untagged frames from being
forwarded too.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Whether VLAN-aware or not, on every VID VLAN table entry that has the CPU
port as a member of it, frames are set to egress the CPU port with the VLAN
tag stacked. This is so that VLAN tags can be appended after hardware
special tag (called DSA tag in the context of Linux drivers).
For user ports on a VLAN-unaware bridge, frame ingressing the user port
egresses CPU port with only the special tag.
For user ports on a VLAN-aware bridge, frame ingressing the user port
egresses CPU port with the special tag and the VLAN tag.
This causes issues with link-local frames, specifically BPDUs, because the
software expects to receive them VLAN-untagged.
There are two options to make link-local frames egress untagged. Setting
CONSISTENT or UNTAGGED on the EG_TAG bits on the relevant register.
CONSISTENT means frames egress exactly as they ingress. That means
egressing with the VLAN tag they had at ingress or egressing untagged if
they ingressed untagged. Although link-local frames are not supposed to be
transmitted VLAN-tagged, if they are done so, when egressing through a CPU
port, the special tag field will be broken.
BPDU egresses CPU port with VLAN tag egressing stacked, received on
software:
00:01:25.104821 AF Unknown (382365846), length 106:
| STAG | | VLAN |
0x0000: 0000 6c27 614d 4143 0001 0000 8100 0001 ..l'aMAC........
0x0010: 0026 4242 0300 0000 0000 0000 6c27 614d .&BB........l'aM
0x0020: 4143 0000 0000 0000 6c27 614d 4143 0000 AC......l'aMAC..
0x0030: 0000 1400 0200 0f00 0000 0000 0000 0000 ................
BPDU egresses CPU port with VLAN tag egressing untagged, received on
software:
00:23:56.628708 AF Unknown (25215488), length 64:
| STAG |
0x0000: 0000 6c27 614d 4143 0001 0000 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
BPDU egresses CPU port with VLAN tag egressing tagged, received on
software:
00:01:34.311963 AF Unknown (25215488), length 64:
| Mess |
0x0000: 0000 6c27 614d 4143 0001 0001 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
To prevent confusing the software, force the frame to egress UNTAGGED
instead of CONSISTENT. This way, frames can't possibly be received TAGGED
by software which would have the special tag field broken.
VLAN Tag Egress Procedure
For all frames, one of these options set the earliest in this order will
apply to the frame:
- EG_TAG in certain registers for certain frames.
This will apply to frame with matching MAC DA or EtherType.
- EG_TAG in the address table.
This will apply to frame at its incoming port.
- EG_TAG in the PVC register.
This will apply to frame at its incoming port.
- EG_CON and [EG_TAG per port] in the VLAN table.
This will apply to frame at its outgoing port.
- EG_TAG in the PCR register.
This will apply to frame at its outgoing port.
EG_TAG in certain registers for certain frames:
PPPoE Discovery_ARP/RARP: PPP_EG_TAG and ARP_EG_TAG in the APC register.
IGMP_MLD: IGMP_EG_TAG and MLD_EG_TAG in the IMC register.
BPDU and PAE: BPDU_EG_TAG and PAE_EG_TAG in the BPC register.
REV_01 and REV_02: R01_EG_TAG and R02_EG_TAG in the RGAC1 register.
REV_03 and REV_0E: R03_EG_TAG and R0E_EG_TAG in the RGAC2 register.
REV_10 and REV_20: R10_EG_TAG and R20_EG_TAG in the RGAC3 register.
REV_21 and REV_UN: R21_EG_TAG and RUN_EG_TAG in the RGAC4 register.
With this change, it can be observed that a bridge interface with stp_state
and vlan_filtering enabled will properly block ports now.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Yan Zhai says:
====================
Report RCU QS for busy network kthreads
This changeset fixes a common problem for busy networking kthreads.
These threads, e.g. NAPI threads, typically will do:
* polling a batch of packets
* if there are more work, call cond_resched() to allow scheduling
* continue to poll more packets when rx queue is not empty
We observed this being a problem in production, since it can block RCU
tasks from making progress under heavy load. Investigation indicates
that just calling cond_resched() is insufficient for RCU tasks to reach
quiescent states. This also has the side effect of frequently clearing
the TIF_NEED_RESCHED flag on voluntary preempt kernels. As a result,
schedule() will not be called in these circumstances, despite schedule()
in fact provides required quiescent states. This at least affects NAPI
threads, napi_busy_loop, and also cpumap kthread.
By reporting RCU QSes in these kthreads periodically before cond_resched, the
blocked RCU waiters can correctly progress. Instead of just reporting QS for
RCU tasks, these code share the same concern as noted in the commit
d28139c4e9 ("rcu: Apply RCU-bh QSes to RCU-sched and RCU-preempt when safe").
So report a consolidated QS for safety.
It is worth noting that, although this problem is reproducible in
napi_busy_loop, it only shows up when setting the polling interval to as high
as 2ms, which is far larger than recommended 50us-100us in the documentation.
So napi_busy_loop is left untouched.
Lastly, this does not affect RT kernels, which does not enter the scheduler
through cond_resched(). Without the mentioned side effect, schedule() will
be called time by time, and clear the RCU task holdouts.
V4: https://lore.kernel.org/bpf/cover.1710525524.git.yan@cloudflare.com/
V3: https://lore.kernel.org/lkml/20240314145459.7b3aedf1@kernel.org/t/
V2: https://lore.kernel.org/bpf/ZeFPz4D121TgvCje@debian.debian/
V1: https://lore.kernel.org/lkml/Zd4DXTyCf17lcTfq@debian.debian/#t
====================
Link: https://lore.kernel.org/r/cover.1710877680.git.yan@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NAPI threads can keep polling packets under load. Currently it is only
calling cond_resched() before repolling, but it is not sufficient to
clear out the holdout of RCU tasks, which prevent BPF tracing programs
from detaching for long period. This can be reproduced easily with
following set up:
ip netns add test1
ip netns add test2
ip -n test1 link add veth1 type veth peer name veth2 netns test2
ip -n test1 link set veth1 up
ip -n test1 link set lo up
ip -n test2 link set veth2 up
ip -n test2 link set lo up
ip -n test1 addr add 192.168.1.2/31 dev veth1
ip -n test1 addr add 1.1.1.1/32 dev lo
ip -n test2 addr add 192.168.1.3/31 dev veth2
ip -n test2 addr add 2.2.2.2/31 dev lo
ip -n test1 route add default via 192.168.1.3
ip -n test2 route add default via 192.168.1.2
for i in `seq 10 210`; do
for j in `seq 10 210`; do
ip netns exec test2 iptables -I INPUT -s 3.3.$i.$j -p udp --dport 5201
done
done
ip netns exec test2 ethtool -K veth2 gro on
ip netns exec test2 bash -c 'echo 1 > /sys/class/net/veth2/threaded'
ip netns exec test1 ethtool -K veth1 tso off
Then run an iperf3 client/server and a bpftrace script can trigger it:
ip netns exec test2 iperf3 -s -B 2.2.2.2 >/dev/null&
ip netns exec test1 iperf3 -c 2.2.2.2 -B 1.1.1.1 -u -l 1500 -b 3g -t 100 >/dev/null&
bpftrace -e 'kfunc:__napi_poll{@=count();} interval:s:1{exit();}'
Report RCU quiescent states periodically will resolve the issue.
Fixes: 29863d41bb ("net: implement threaded-able napi poll loop support")
Reviewed-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/4c3b0d3f32d3b18949d75b18e5e1d9f13a24f025.1710877680.git.yan@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When under heavy load, network processing can run CPU-bound for many
tens of seconds. Even in preemptible kernels (non-RT kernel), this can
block RCU Tasks grace periods, which can cause trace-event removal to
take more than a minute, which is unacceptably long.
This commit therefore creates a new helper function that passes through
both RCU and RCU-Tasks quiescent states every 100 milliseconds. This
hard-coded value suffices for current workloads.
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/90431d46ee112d2b0af04dbfe936faaca11810a5.1710877680.git.yan@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Subbaraya Sundeep says:
====================
octeontx2-pf: RVU Mailbox fixes
This patchset fixes the problems related to RVU mailbox.
During long run tests some times VF commands like setting
MTU or toggling interface fails because VF mailbox is timedout
waiting for response from PF.
Below are the fixes
Patch 1: There are two types of messages in RVU mailbox namely up and down
messages. Down messages are synchronous messages where a PF/VF sends
a message to AF and AF replies back with response. UP messages are
notifications and are asynchronous like AF sending link events to
PF. When VF sends a down message to PF, PF forwards to AF and sends
the response from AF back to VF. PF has to forward VF messages since
there is no path in hardware for VF to send directly to AF.
There is one mailbox interrupt from AF to PF when raised could mean
two scenarios one is where AF sending reply to PF for a down message
sent by PF and another one is AF sending up message asynchronously
when link changed for that PF. Receiving the up message interrupt while
PF is in middle of forwarding down message causes mailbox errors.
Fix this by receiver detecting the type of message from the mbox data register
set by sender.
Patch 2:
During VF driver remove, VF has to wait until last message is
completed and then turn off mailbox interrupts from PF.
Patch 3:
Do not use ordered workqueue for message processing since multiple works are
queued simultaneously by all the VFs and PF link UP messages.
Patch 4:
When sending link event to VF by PF check whether VF is really up to
receive this message.
Patch 5:
In AF driver, use separate interrupt handlers for the AF-VF interrupt and
AF-PF interrupt. Sometimes both interrupts are raised to two CPUs at same
time and both CPUs execute same function at same time corrupting the data.
v2 changes:
Added missing mutex unlock in error path in patch 1
Refactored if else logic in patch 1 as suggested by Paolo Abeni
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For PF to AF interrupt vector and VF to AF vector same
interrupt handler is registered which is causing race condition.
When two interrupts are raised to two CPUs at same time
then two cores serve same event corrupting the data.
Fixes: 7304ac4567 ("octeontx2-af: Add mailbox IRQ and msg handlers")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PF sending link status messages to VF, it is possible
that by the time link_event_task work function is executed
VF might have brought down. Hence before sending VF link
status message check whether VF is up to receive it.
Fixes: ad513ed938 ("octeontx2-vf: Link event notification support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one execution context for the workqueue used for PF and
VFs mailbox communication is incorrect since multiple works are
queued simultaneously by all the VFs and PF link UP messages.
Hence use default number of execution contexts by passing zero
as max_active to alloc_workqueue function. With this fix in place,
modify UP messages also to wait until completion.
Fixes: d424b6c024 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During VF driver remove, a message is sent to detach VF
resources to PF but VF is not waiting until message is
complete. Also mailbox interrupts need to be turned off
after the detach resource message is complete. This patch
fixes that problem.
Fixes: 05fcc9e089 ("octeontx2-pf: Attach NIX and NPA block LFs")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single line of interrupt is used to receive up notifications
and down reply messages from AF to PF (similarly from PF to its VF).
PF acts as bridge and forwards VF messages to AF and sends respsones
back from AF to VF. When an async event like link event is received
by up message when PF is in middle of forwarding VF message then
mailbox errors occur because PF state machine is corrupted.
Since VF is a separate driver or VF driver can be in a VM it is
not possible to serialize from the start of communication at VF.
Hence to differentiate between type of messages at PF this patch makes
sender to set mbox data register with distinct values for up and down
messages. Sender also checks whether previous interrupt is received
before triggering current interrupt by waiting for mailbox data register
to become zero.
Fixes: 5a6d7c9dae ("octeontx2-pf: Mailbox communication with AF")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2024-03-19
1) Fix possible page_pool leak triggered by esp_output.
From Dragos Tatulea.
2) Fix UDP encapsulation in software GSO path.
From Leon Romanovsky.
* tag 'ipsec-2024-03-19' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
xfrm: Allow UDP encapsulation only in offload modes
net: esp: fix bad handling of pages from page_pool
====================
Link: https://lore.kernel.org/r/20240319110151.409825-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix race condition leading to system crash during EEH error handling
During EEH error recovery, the bnx2x driver's transmit timeout logic
could cause a race condition when handling reset tasks. The
bnx2x_tx_timeout() schedules reset tasks via bnx2x_sp_rtnl_task(),
which ultimately leads to bnx2x_nic_unload(). In bnx2x_nic_unload()
SGEs are freed using bnx2x_free_rx_sge_range(). However, this could
overlap with the EEH driver's attempt to reset the device using
bnx2x_io_slot_reset(), which also tries to free SGEs. This race
condition can result in system crashes due to accessing freed memory
locations in bnx2x_free_rx_sge()
799 static inline void bnx2x_free_rx_sge(struct bnx2x *bp,
800 struct bnx2x_fastpath *fp, u16 index)
801 {
802 struct sw_rx_page *sw_buf = &fp->rx_page_ring[index];
803 struct page *page = sw_buf->page;
....
where sw_buf was set to NULL after the call to dma_unmap_page()
by the preceding thread.
EEH: Beginning: 'slot_reset'
PCI 0011:01:00.0#10000: EEH: Invoking bnx2x->slot_reset()
bnx2x: [bnx2x_io_slot_reset:14228(eth1)]IO slot reset initializing...
bnx2x 0011:01:00.0: enabling device (0140 -> 0142)
bnx2x: [bnx2x_io_slot_reset:14244(eth1)]IO slot reset --> driver unload
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc0080000025065fc
Oops: Kernel access of bad area, sig: 11 [#1]
.....
Call Trace:
[c000000003c67a20] [c00800000250658c] bnx2x_io_slot_reset+0x204/0x610 [bnx2x] (unreliable)
[c000000003c67af0] [c0000000000518a8] eeh_report_reset+0xb8/0xf0
[c000000003c67b60] [c000000000052130] eeh_pe_report+0x180/0x550
[c000000003c67c70] [c00000000005318c] eeh_handle_normal_event+0x84c/0xa60
[c000000003c67d50] [c000000000053a84] eeh_event_handler+0xf4/0x170
[c000000003c67da0] [c000000000194c58] kthread+0x1c8/0x1d0
[c000000003c67e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64
To solve this issue, we need to verify page pool allocations before
freeing.
Fixes: 4cace675d6 ("bnx2x: Alloc 4k fragment for each rx ring buffer element")
Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240315205535.1321-1-thinhtr@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
read_poll_timeout inside phy_read_poll_timeout can set val negative
in some cases (for example, __mdiobus_read inside phy_read can return
-EOPNOTSUPP).
Supposedly, commit 4ec7329517 ("net: phylib: fix phy_read*_poll_timeout()")
should fix problems with wrong-signed vals, but I do not see how
as val is sent to phy_read as is and __val = phy_read (not val)
is checked for sign.
Change val type for signed to allow better error handling as done in other
phy_read_poll_timeout callers. This will not fix any error handling
by itself, but allows, for example, to modify cond with appropriate
sign check or check resulting val separately.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 014068dcb5 ("net: phy: genphy_loopback: add link speed configuration")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The commit 2c15a5aee2 ("net/sched: Load modules via their alias")
starts loading modules via aliases and not canonical names. The new
aliases were added in commit 241a94abcf ("net/sched: Add module
aliases for cls_,sch_,act_ modules") via a Coccinele script.
sch_fq_pie.c is missing module.h header and thus Coccinele did not patch
it. Add the include and module alias manually, so that autoloading works
for sch_fq_pie too.
(Note: commit message in commit 241a94abcf ("net/sched: Add module
aliases for cls_,sch_,act_ modules") was mangled due to '#'
misinterpretation. The predicate haskernel is:
| @ haskernel @
| @@
|
| #include <linux/module.h>
|
.)
Fixes: 241a94abcf ("net/sched: Add module aliases for cls_,sch_,act_ modules")
Signed-off-by: Michal Koutný <mkoutny@suse.com>
Link: https://lore.kernel.org/r/20240315160210.8379-1-mkoutny@suse.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since the referenced commit, the xfrm_inner_extract_output() function
uses the protocol field to determine the address family. So not setting
it for IPv4 raw sockets meant that such packets couldn't be tunneled via
IPsec anymore.
IPv6 raw sockets are not affected as they already set the protocol since
9c9c9ad5fa ("ipv6: set skb->protocol on tcp, raw and ip6_append_data
genereated skbs").
Fixes: f4796398f2 ("xfrm: Remove inner/outer modes from output path")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/c5d9a947-eb19-4164-ac99-468ea814ce20@strongswan.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A failure during registration of the netdev notifier was not handled at
all. A failure during netlink initialization did not unregister the netdev
notifier.
Handle failures of netdev notifier registration and netlink initialization.
Both functions should only return negative values on failure and thereby
lead to the hsr module not being loaded.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Reviewed-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/3ce097c15e3f7ace98fc7fd9bcbf299f092e63d1.1710504184.git.fmaurer@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
acquire/release_in_xmit() work as bit lock in rds_send_xmit(), so they
are expected to ensure acquire/release memory ordering semantics.
However, test_and_set_bit/clear_bit() don't imply such semantics, on
top of this, following smp_mb__after_atomic() does not guarantee release
ordering (memory barrier actually should be placed before clear_bit()).
Instead, we use clear_bit_unlock/test_and_set_bit_lock() here.
Fixes: 0f4b1c7e89 ("rds: fix rds_send_xmit() serialization")
Fixes: 1f9ecd7eac ("RDS: Pass rds_conn_path to rds_send_xmit()")
Signed-off-by: Yewon Choi <woni9911@gmail.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/ZfQUxnNTO9AJmzwc@libra05
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jason A. Donenfeld says:
====================
wireguard fixes for 6.9-rc1
This series has four WireGuard fixes:
1) Annotate a data race that KCSAN found by using READ_ONCE/WRITE_ONCE,
which has been causing syzkaller noise.
2) Use the generic netdev tstats allocation and stats getters instead of
doing this within the driver.
3) Explicitly check a flag variable instead of an empty list in the
netlink code, to prevent a UaF situation when paging through GET
results during a remove-all SET operation.
4) Set a flag in the RISC-V CI config so the selftests continue to boot.
====================
Link: https://lore.kernel.org/r/20240314224911.6653-1-Jason@zx2c4.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This option is needed to continue booting with QEMU. Recent changes that
made this optional meant that it gets unset in the test harness, and so
WireGuard CI has been broken. Fix this by simply setting this option.
Cc: stable@vger.kernel.org
Fixes: 496ea826d1 ("RISC-V: provide Kconfig & commandline options to control parsing "riscv,isa"")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The previous commit fixed a bug that led to a NULL peer->device being
dereferenced. It's actually easier and faster performance-wise to
instead get the device from ctx->wg. This semantically makes more sense
too, since ctx->wg->peer_allowedips.seq is compared with
ctx->allowedips_seq, basing them both in ctx. This also acts as a
defence in depth provision against freed peers.
Cc: stable@vger.kernel.org
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If all peers are removed via wg_peer_remove_all(), rather than setting
peer_list to empty, the peer is added to a temporary list with a head on
the stack of wg_peer_remove_all(). If a netlink dump is resumed and the
cursored peer is one that has been removed via wg_peer_remove_all(), it
will iterate from that peer and then attempt to dump freed peers.
Fix this by instead checking peer->is_dead, which was explictly created
for this purpose. Also move up the device_update_lock lockdep assertion,
since reading is_dead relies on that.
It can be reproduced by a small script like:
echo "Setting config..."
ip link add dev wg0 type wireguard
wg setconf wg0 /big-config
(
while true; do
echo "Showing config..."
wg showconf wg0 > /dev/null
done
) &
sleep 4
wg setconf wg0 <(printf "[Peer]\nPublicKey=$(wg genkey)\n")
Resulting in:
BUG: KASAN: slab-use-after-free in __lock_acquire+0x182a/0x1b20
Read of size 8 at addr ffff88811956ec70 by task wg/59
CPU: 2 PID: 59 Comm: wg Not tainted 6.8.0-rc2-debug+ #5
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x70
print_address_description.constprop.0+0x2c/0x380
print_report+0xab/0x250
kasan_report+0xba/0xf0
__lock_acquire+0x182a/0x1b20
lock_acquire+0x191/0x4b0
down_read+0x80/0x440
get_peer+0x140/0xcb0
wg_get_device_dump+0x471/0x1130
Cc: stable@vger.kernel.org
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Reported-by: Lillian Berry <lillian@star-ark.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core
and convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in this driver and leverage the network core
allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Syzkaller with KCSAN identified a data-race issue when accessing
keypair->receiving_counter.counter. Use READ_ONCE() and WRITE_ONCE()
annotations to mark the data race as intentional.
BUG: KCSAN: data-race in wg_packet_decrypt_worker / wg_packet_rx_poll
write to 0xffff888107765888 of 8 bytes by interrupt on cpu 0:
counter_validate drivers/net/wireguard/receive.c:321 [inline]
wg_packet_rx_poll+0x3ac/0xf00 drivers/net/wireguard/receive.c:461
__napi_poll+0x60/0x3b0 net/core/dev.c:6536
napi_poll net/core/dev.c:6605 [inline]
net_rx_action+0x32b/0x750 net/core/dev.c:6738
__do_softirq+0xc4/0x279 kernel/softirq.c:553
do_softirq+0x5e/0x90 kernel/softirq.c:454
__local_bh_enable_ip+0x64/0x70 kernel/softirq.c:381
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
_raw_spin_unlock_bh+0x36/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:396 [inline]
ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
wg_packet_decrypt_worker+0x6c5/0x700 drivers/net/wireguard/receive.c:499
process_one_work kernel/workqueue.c:2633 [inline]
...
read to 0xffff888107765888 of 8 bytes by task 3196 on cpu 1:
decrypt_packet drivers/net/wireguard/receive.c:252 [inline]
wg_packet_decrypt_worker+0x220/0x700 drivers/net/wireguard/receive.c:501
process_one_work kernel/workqueue.c:2633 [inline]
process_scheduled_works+0x5b8/0xa30 kernel/workqueue.c:2706
worker_thread+0x525/0x730 kernel/workqueue.c:2787
...
Fixes: a9e90d9931 ("wireguard: noise: separate receive counter from send counter")
Reported-by: syzbot+d1de830e4ecdaac83d89@syzkaller.appspotmail.com
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This reverts commit 885c36e59f.
The patch currently broke the bpf selftest test_tc_dtime because
uapi field __sk_buff->tstamp_type depends on skb->mono_delivery_time which
does not necessarily mean mono with the original fix as the bit was re-used
for userspace timestamp as well to avoid tstamp reset in the forwarding
path. To solve this we need to keep mono_delivery_time as is and
introduce another bit called user_delivery_time and fall back to the
initial proposal of setting the user_delivery_time bit based on
sk_clockid set from userspace.
Fixes: 885c36e59f ("net: Re-use and set mono_delivery_time bit for userspace tstamp packets")
Link: https://lore.kernel.org/netdev/bc037db4-58bb-4861-ac31-a361a93841d3@linux.dev/
Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On MT7530, the HT_XTAL_FSEL field of the HWTRAP register stores a 2-bit
value that represents the frequency of the crystal oscillator connected to
the switch IC. The field is populated by the state of the ESW_P4_LED_0 and
ESW_P4_LED_0 pins, which is done right after reset is deasserted.
ESW_P4_LED_0 ESW_P3_LED_0 Frequency
-----------------------------------------
0 0 Reserved
0 1 20MHz
1 0 40MHz
1 1 25MHz
On MT7531, the XTAL25 bit of the STRAP register stores this. The LAN0LED0
pin is used to populate the bit. 25MHz when the pin is high, 40MHz when
it's low.
These pins are also used with LEDs, therefore, their state can be set to
something other than the bootstrapping configuration. For example, a link
may be established on port 3 before the DSA subdriver takes control of the
switch which would set ESW_P3_LED_0 to high.
Currently on mt7530_setup() and mt7531_setup(), 1000 - 1100 usec delay is
described between reset assertion and deassertion. Some switch ICs in real
life conditions cannot always have these pins set back to the bootstrapping
configuration before reset deassertion in this amount of delay. This causes
wrong crystal frequency to be selected which puts the switch in a
nonfunctional state after reset deassertion.
The tests below are conducted on an MT7530 with a 40MHz crystal oscillator
by Justin Swartz.
With a cable from an active peer connected to port 3 before reset, an
incorrect crystal frequency (0b11 = 25MHz) is selected:
[1] [3] [5]
: : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
_____________________________
ESW_P3_LED_0 |__________________________
: : : :
: : [4]...:
: :
[2]................:
[1] Reset is asserted.
[2] Period of 1000 - 1100 usec.
[3] Reset is deasserted.
[4] Period of 315 usec. HWTRAP register is populated with incorrect
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
Increase the delay between reset_control_assert() and
reset_control_deassert(), and gpiod_set_value_cansleep(priv->reset, 0) and
gpiod_set_value_cansleep(priv->reset, 1) to 5000 - 5100 usec. This amount
ensures a higher possibility that the switch IC will have these pins back
to the bootstrapping configuration before reset deassertion.
With a cable from an active peer connected to port 3 before reset, the
correct crystal frequency (0b10 = 40MHz) is selected:
[1] [2-1] [3] [5]
: : : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
___________________ _______
ESW_P3_LED_0 |_________| |__________________
: : : : :
: [2-2]...: [4]...:
[2]................:
[1] Reset is asserted.
[2] Period of 5000 - 5100 usec.
[2-1] ESW_P3_LED_0 goes low.
[2-2] Remaining period of 5000 - 5100 usec.
[3] Reset is deasserted.
[4] Period of 310 usec. HWTRAP register is populated with bootstrapped
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
ESW_P3_LED_0 low period before reset deassertion:
5000 usec
- 5100 usec
TEST RESET HOLD
# (usec)
---------------------
1 5410
2 5440
3 4375
4 5490
5 5475
6 4335
7 4370
8 5435
9 4205
10 4335
11 3750
12 3170
13 4395
14 4375
15 3515
16 4335
17 4220
18 4175
19 4175
20 4350
Min 3170
Max 5490
Median 4342.500
Avg 4466.500
Revert commit 2920dd92b9 ("net: dsa: mt7530: disable LEDs before reset").
Changing the state of pins via reset assertion is simpler and more
efficient than doing so by setting the LED controller off.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Co-developed-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignat Korchagin says:
====================
net: veth: ability to toggle GRO and XDP independently
It is rather confusing that GRO is automatically enabled, when an XDP program
is attached to a veth interface. Moreover, it is not possible to disable GRO
on a veth, if an XDP program is attached (which might be desirable in some use
cases).
Make GRO and XDP independent for a veth interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be able to independently flip either XDP or GRO states and toggling
one should not affect the other.
Adjust other tests as well that had implicit expectation that GRO would be
automatically enabled.
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d3256efd8e ("veth: allow enabling NAPI even without XDP") tried to fix
the fact that GRO was not possible without XDP, because veth did not use NAPI
without XDP. However, it also introduced the behaviour that GRO is always
enabled, when XDP is enabled.
While it might be desired for most cases, it is confusing for the user at best
as the GRO flag suddenly changes, when an XDP program is attached. It also
introduces some complexities in state management as was partially addressed in
commit fe9f801355 ("net: veth: clear GRO when clearing XDP even when down").
But the biggest problem is that it is not possible to disable GRO at all, when
an XDP program is attached, which might be needed for some use cases.
Fix this by not touching the GRO flag on XDP enable/disable as the code already
supports switching to NAPI if either GRO or XDP is requested.
Link: https://lore.kernel.org/lkml/20240311124015.38106-1-ignat@cloudflare.com/
Fixes: d3256efd8e ("veth: allow enabling NAPI even without XDP")
Fixes: fe9f801355 ("net: veth: clear GRO when clearing XDP even when down")
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the skb is reorganized during esp_output (!esp->inline), the pages
coming from the original skb fragments are supposed to be released back
to the system through put_page. But if the skb fragment pages are
originating from a page_pool, calling put_page on them will trigger a
page_pool leak which will eventually result in a crash.
This leak can be easily observed when using CONFIG_DEBUG_VM and doing
ipsec + gre (non offloaded) forwarding:
BUG: Bad page state in process ksoftirqd/16 pfn:1451b6
page:00000000de2b8d32 refcount:0 mapcount:0 mapping:0000000000000000 index:0x1451b6000 pfn:0x1451b6
flags: 0x200000000000000(node=0|zone=2)
page_type: 0xffffffff()
raw: 0200000000000000 dead000000000040 ffff88810d23c000 0000000000000000
raw: 00000001451b6000 0000000000000001 00000000ffffffff 0000000000000000
page dumped because: page_pool leak
Modules linked in: ip_gre gre mlx5_ib mlx5_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat nf_nat xt_addrtype br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_uverbs ib_core overlay zram zsmalloc fuse [last unloaded: mlx5_core]
CPU: 16 PID: 96 Comm: ksoftirqd/16 Not tainted 6.8.0-rc4+ #22
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x36/0x50
bad_page+0x70/0xf0
free_unref_page_prepare+0x27a/0x460
free_unref_page+0x38/0x120
esp_ssg_unref.isra.0+0x15f/0x200
esp_output_tail+0x66d/0x780
esp_xmit+0x2c5/0x360
validate_xmit_xfrm+0x313/0x370
? validate_xmit_skb+0x1d/0x330
validate_xmit_skb_list+0x4c/0x70
sch_direct_xmit+0x23e/0x350
__dev_queue_xmit+0x337/0xba0
? nf_hook_slow+0x3f/0xd0
ip_finish_output2+0x25e/0x580
iptunnel_xmit+0x19b/0x240
ip_tunnel_xmit+0x5fb/0xb60
ipgre_xmit+0x14d/0x280 [ip_gre]
dev_hard_start_xmit+0xc3/0x1c0
__dev_queue_xmit+0x208/0xba0
? nf_hook_slow+0x3f/0xd0
ip_finish_output2+0x1ca/0x580
ip_sublist_rcv_finish+0x32/0x40
ip_sublist_rcv+0x1b2/0x1f0
? ip_rcv_finish_core.constprop.0+0x460/0x460
ip_list_rcv+0x103/0x130
__netif_receive_skb_list_core+0x181/0x1e0
netif_receive_skb_list_internal+0x1b3/0x2c0
napi_gro_receive+0xc8/0x200
gro_cell_poll+0x52/0x90
__napi_poll+0x25/0x1a0
net_rx_action+0x28e/0x300
__do_softirq+0xc3/0x276
? sort_range+0x20/0x20
run_ksoftirqd+0x1e/0x30
smpboot_thread_fn+0xa6/0x130
kthread+0xcd/0x100
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x31/0x50
? kthread_complete_and_exit+0x20/0x20
ret_from_fork_asm+0x11/0x20
</TASK>
The suggested fix is to introduce a new wrapper (skb_page_unref) that
covers page refcounting for page_pool pages as well.
Cc: stable@vger.kernel.org
Fixes: 6a5bcd84e8 ("page_pool: Allow drivers to hint on SKB recycling")
Reported-and-tested-by: Anatoli N.Chechelnickiy <Anatoli.Chechelnickiy@m.interpipe.biz>
Reported-by: Ian Kumlien <ian.kumlien@gmail.com>
Link: https://lore.kernel.org/netdev/CAA85sZvvHtrpTQRqdaOx6gd55zPAVsqMYk_Lwh4Md5knTq7AyA@mail.gmail.com
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Clearing bit MAC_MCR_FORCE_LINK which forces the link down too early
can result in MAC ending up in a broken/blocked state.
Fix this by handling this bit in the .mac_link_up and .mac_link_down
calls instead of in .mac_finish.
Fixes: b8fc9f3082 ("net: ethernet: mediatek: Add basic PHYLINK support")
Suggested-by: Mason-cw Chang <Mason-cw.Chang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 411c5f3680 ("mm/page_alloc: modify page_frag_alloc_align() to
accept align as an argument") changed the way page_frag_alloc_align()
worked, but it didn't fix AF_RXRPC as that use of that allocator function
hadn't been merged yet at the time. Now, when the AFS filesystem is used,
this results in:
WARNING: CPU: 4 PID: 379 at include/linux/gfp.h:323 rxrpc_alloc_data_txbuf+0x9d/0x2b0 [rxrpc]
Fix this by using __page_frag_alloc_align() instead.
Note that it might be better to use an order-based alignment rather than a
mask-based alignment.
Fixes: 49489bb03a ("rxrpc: Do zerocopy using MSG_SPLICE_PAGES and page frags")
Signed-off-by: David Howells <dhowells@redhat.com>
Reported-by: Marc Dionne <marc.dionne@auristor.com>
cc: Yunsheng Lin <linyunsheng@huawei.com>
cc: Alexander Duyck <alexander.duyck@gmail.com>
cc: Michael S. Tsirkin <mst@redhat.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Arınç ÜNAL