[ Upstream commit bce3f77068 ]
When processing a SYSERR, if the device does not respond to the MHI_RESET
from the host, the host will be stuck in a difficult to recover state.
The host will remain in MHI_PM_SYS_ERR_PROCESS and not clean up the host
channels. Clients will not be notified of the SYSERR via the destruction
of their channel devices, which means clients may think that the device is
still up. Subsequent SYSERR events such as a device fatal error will not
be processed as the state machine cannot transition from PROCESS back to
DETECT. The only way to recover from this is to unload the mhi module
(wipe the state machine state) or for the mhi controller to initiate
SHUTDOWN.
This issue was discovered by stress testing soc_reset events on AIC100
via the sysfs node.
soc_reset is processed entirely in hardware. When the register write
hits the endpoint hardware, it causes the soc to reset without firmware
involvement. In stress testing, there is a rare race where soc_reset N
will cause the soc to reset and PBL to signal SYSERR (fatal error). If
soc_reset N+1 is triggered before PBL can process the MHI_RESET from the
host, then the soc will reset again, and re-run PBL from the beginning.
This will cause PBL to lose all state. PBL will be waiting for the host
to respond to the new syserr, but host will be stuck expecting the
previous MHI_RESET to be processed.
Additionally, the AMSS EE firmware (QSM) was hacked to synthetically
reproduce the issue by simulating a FW hang after the QSM issued a
SYSERR. In this case, soc_reset would not recover the device.
For this failure case, to recover the device, we need a state similar to
PROCESS, but can transition to DETECT. There is not a viable existing
state to use. POR has the needed transitions, but assumes the device is
in a good state and could allow the host to attempt to use the device.
Allowing PROCESS to transition to DETECT invites the possibility of
parallel SYSERR processing which could get the host and device out of
sync.
Thus, invent a new state - MHI_PM_SYS_ERR_FAIL
This essentially a holding state. It allows us to clean up the host
elements that are based on the old state of the device (channels), but
does not allow us to directly advance back to an operational state. It
does allow the detection and processing of another SYSERR which may
recover the device, or allows the controller to do a clean shutdown.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240112180800.536733-1-quic_jhugo@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4acd21a45c ]
Update the architecture dependency to be the generic Tegra
because the driver works on the four latest Tegra generations
not just Tegra210, if you build a kernel with a specific
ARCH_TEGRA_xxx_SOC option that excludes Tegra210 you don't get
this driver.
Fixes: 46a88534af ("bus: Add support for Tegra ACONNECT")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f71f6ff8c1 upstream.
Commit 34539b442b ("bus: ti-sysc: Flush posted write on enable before
reset") caused a regression reproducable on omap4 duovero where the ISS
target module can produce interconnect errors on boot. Turns out the
registers are not accessible until after a delay for devices needing
a ti,sysc-delay-us value.
Let's fix this by flushing the posted write only after the reset delay.
We do flushing also for ti,sysc-delay-us using devices as that should
trigger an interconnect error if the delay is not properly configured.
Let's also add some comments while at it.
Fixes: 34539b442b ("bus: ti-sysc: Flush posted write on enable before reset")
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e5deb8f76e ]
The uarts should be tagged with SYSC_QUIRK_SWSUP_SIDLE instead of
SYSC_QUIRK_SWSUP_SIDLE_ACT. The difference is that SYSC_QUIRK_SWSUP_SIDLE
is used to force idle target modules rather than block idle during usage.
The SYSC_QUIRK_SWSUP_SIDLE_ACT should disable autoidle and wake-up when
a target module is active, and configure autoidle and wake-up when a
target module is inactive. We are missing configuring the target module
on sysc_disable_module(), and missing toggling of the wake-up bit.
Let's fix the issue to allow uart wake-up to work.
Fixes: fb685f1c19 ("bus: ti-sysc: Handle swsup idle mode quirks")
Tested-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11729caa52 ]
Commit feaa8baee8 ("bus: ti-sysc: Implement SoC revision handling")
created a list of SoC types searching for strings based on names
and wildcards which associates the SoC to different families.
The OMAP34xx and OMAP35xx are treated as SOC_3430 while
OMAP36xx and OMAP37xx are treated as SOC_3630, but the AM35xx
isn't listed.
The AM35xx is mostly an OMAP3430, and a later commit a12315d6d2
("bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific") looks
for the SOC type and behaves in a certain way if it's SOC_3430.
This caused a regression on the AM3517 causing it to return two
errors:
ti-sysc: probe of 48318000.target-module failed with error -16
ti-sysc: probe of 49032000.target-module failed with error -16
Fix this by treating the creating SOC_AM35 and inserting it between
the SOC_3430 and SOC_3630. If it is treaed the same way as the
SOC_3430 when checking the status of sysc_check_active_timer,
the error conditions will disappear.
Fixes: a12315d6d2 ("bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific")
Fixes: feaa8baee8 ("bus: ti-sysc: Implement SoC revision handling")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-ID: <20230906233442.270835-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d929b2b746 ]
The am335x-evm started producing boot errors because of subtle timing
changes:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xf03c1010
...
sysc_reset from sysc_probe+0xf60/0x1514
sysc_probe from platform_probe+0x5c/0xbc
...
The fix consists in using the appropriate sleep function in sysc reset.
For flexible sleeping, fsleep is recommended. Here, sysc delay parameter
can take any value in [0 - 255] us range. As a result, fsleep() should
be used, calling udelay() for a sysc delay lower than 10 us.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Fixes: e709ed70d1 ("bus: ti-sysc: Fix missing reset delay handling")
Message-ID: <20230821-fix-ti-sysc-reset-v1-1-5a0a5d8fae55@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03a711d3cb ]
Enable the uart quirks similar to the earlier SoCs. Let's assume we are
likely going to need a k3 specific quirk mask separate from the earlier
SoCs, so let's not start changing the revision register mask at this point.
Note that SYSC_QUIRK_LEGACY_IDLE will be needed until we can remove the
need for pm_runtime_irq_safe() from 8250_omap driver.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1a50d9403f upstream.
When loading a DT overlay that creates a device, the device is not
probed, unless the DT overlay is unloaded and reloaded again.
After the recent refactoring to improve fw_devlink, it no longer depends
on the "compatible" property to identify which device tree nodes will
become struct devices. fw_devlink now picks up dangling consumers
(consumers pointing to descendent device tree nodes of a device that
aren't converted to child devices) when a device is successfully bound
to a driver. See __fw_devlink_pickup_dangling_consumers().
However, during DT overlay, a device's device tree node can have
sub-nodes added/removed without unbinding/rebinding the driver. This
difference in behavior between the normal device instantiation and
probing flow vs. the DT overlay flow has a bunch of implications that
are pointed out elsewhere[1]. One of them is that the fw_devlink logic
to pick up dangling consumers is never exercised.
This patch solves the fw_devlink issue by marking all DT nodes added by
DT overlays with FWNODE_FLAG_NOT_DEVICE (fwnode that won't become
device), and by clearing the flag when a struct device is actually
created for the DT node. This way, fw_devlink knows not to have
consumers waiting on these newly added DT nodes, and to propagate the
dependency to an ancestor DT node that has the corresponding struct
device.
Based on a patch by Saravana Kannan, which covered only platform and spi
devices.
[1] https://lore.kernel.org/r/CAGETcx_bkuFaLCiPrAWCPQz+w79ccDp6=9e881qmK=vx3hBMyg@mail.gmail.com
Fixes: 4a032827da ("of: property: Simplify of_link_to_phandle()")
Link: https://lore.kernel.org/r/CAGETcx_+rhHvaC_HJXGrr5_WAd2+k5f=rWYnkCZ6z5bGX-wj4w@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Link: https://lore.kernel.org/r/e1fa546682ea4c8474ff997ab6244c5e11b6f8bc.1680182615.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1e1e9bb9d ]
Fix "warning: cast from pointer to integer of different size" on 64-bit
builds.
Note that this is a cosmetic fix at this point as the driver is not yet
used for 64-bit systems.
Fixes: feaa8baee8 ("bus: ti-sysc: Implement SoC revision handling")
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34539b442b ]
The am335x devices started producing boot errors for resetting musb module
in because of subtle timing changes:
Unhandled fault: external abort on non-linefetch (0x1008)
...
sysc_poll_reset_sysconfig from sysc_reset+0x109/0x12
sysc_reset from sysc_probe+0xa99/0xeb0
...
The fix is to flush posted write after enable before reset during
probe. Note that some devices also need to specify the delay after enable
with ti,sysc-delay-us, but this is not needed for musb on am335x based on
my tests.
Reported-by: kernelci.org bot <bot@kernelci.org>
Closes: https://storage.kernelci.org/next/master/next-20230614/arm/multi_v7_defconfig+CONFIG_THUMB2_KERNEL=y/gcc-10/lab-cip/baseline-beaglebone-black.html
Fixes: 596e795569 ("bus: ti-sysc: Add support for software reset")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1d1493bdc2 upstream.
If firmware loading fails, the controller's pm_state is updated to
MHI_PM_FW_DL_ERR unconditionally. This can corrupt the pm_state as the
update is not done under the proper lock, and also does not validate
the state transition. The firmware loading can fail due to a detected
syserr, but if MHI_PM_FW_DL_ERR is unconditionally set as the pm_state,
the handling of the syserr can break when it attempts to transition from
syserr detect, to syserr process.
By grabbing the lock, we ensure we don't race with some other pm_state
update. By using mhi_try_set_pm_state(), we check that the transition
to MHI_PM_FW_DL_ERR is valid via the state machine logic. If it is not
valid, then some other transition is occurring like syserr processing, and
we assume that will resolve the firmware loading error.
Fixes: 12e050c77b ("bus: mhi: core: Move to an error state on any firmware load failure")
Cc: stable@vger.kernel.org
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/1681142292-27571-3-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d469d9448a upstream.
If we detect a system error via intvec, we only process the syserr if the
current ee is different than the last observed ee. The reason for this
check is to prevent bhie from running multiple times, but with the single
queue handling syserr, that is not possible.
The check can cause an issue with device recovery. If PBL loads a bad SBL
via BHI, but that SBL hangs before notifying the host of an ee change,
then issuing soc_reset to crash the device and retry (after supplying a
fixed SBL) will not recover the device as the host will observe a PBL->PBL
transition and not process the syserr. The device will be stuck until
either the driver is reloaded, or the host is rebooted. Instead, remove
the check so that we can attempt to recover the device.
Fixes: ef2126c4e2 ("bus: mhi: core: Process execution environment changes serially")
Cc: stable@vger.kernel.org
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/1681142292-27571-2-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1adab2922c upstream.
If bus type is other than imx50_weim_devtype and have no child devices,
variable 'ret' in function weim_parse_dt() will not be initialized, but
will be used as branch condition and return value. Fix this by
initializing 'ret' with 0.
This was discovered with help of clang-analyzer, but the situation is
quite possible in real life.
Fixes: 52c47b6341 ("bus: imx-weim: improve error handling upon child probe-failure")
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Cc: stable@vger.kernel.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ddc761829 ]
state_lock, the spinlock type is meant to protect race against concurrent
MHI state transitions. In mhi_ep_set_m0_state(), while the state_lock is
being held, the channels are resumed in mhi_ep_resume_channels() if the
previous state was M3. This causes sleeping in atomic bug, since
mhi_ep_resume_channels() use mutex internally.
Since the state_lock is supposed to be held throughout the state change,
it is not ideal to drop the lock before calling mhi_ep_resume_channels().
So to fix this issue, let's change the type of state_lock to mutex. This
would also allow holding the lock throughout all state transitions thereby
avoiding any potential race.
Cc: <stable@vger.kernel.org> # 5.19
Fixes: e4b7b5f0f3 ("bus: mhi: ep: Add support for suspending and resuming channels")
Reported-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d6a1fea53 upstream.
There is a good chance that while the channel ring gets processed, the STOP
or RESET command for the channel might be received from the MHI host. In
those cases, the entire channel ring processing needs to be protected by
chan->lock to prevent the race where the corresponding channel ring might
be reset.
While at it, let's also add a sanity check to make sure that the ring is
started before processing it. Because, if the STOP/RESET command gets
processed while mhi_ep_ch_ring_worker() waited for chan->lock, the ring
would've been reset.
Cc: <stable@vger.kernel.org> # 5.19
Fixes: 03c0bb8ec9 ("bus: mhi: ep: Add support for processing channel rings")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20221228161704.255268-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We face some regressions on a few IXP42x systems when
accessing flash, the following unrelated error prints
appear from the PCI driver:
ixp4xx-pci c0000000.pci: PCI: abort_handler addr = 0xff9ffb5f,
isr = 0x0, status = 0x22a0
ixp4xx-pci c0000000.pci: imprecise abort
(...)
It turns out that while bit 7 is masked "reserved" it is
not unused, so masking it off as zero is dangerous, and
breaks flash access on some systems such as the NSLU2.
Be more careful and avoid masking off any of the reserved
bits 7, 8, 9 or 30. Only keep masking EXP_WORD (bit 2)
on IXP43x which is necessary in some setups.
Fixes: 1c953bda90 ("bus: ixp4xx: Add a driver for IXP4xx expansion bus")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221122134411.2030372-1-linus.walleij@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
Pull ARM driver updates from Arnd Bergmann:
"The drivers branch for 6.1 is a bit larger than for most releases.
Most of the changes come from SoC maintainers for the drivers/soc
subsystem:
- A new driver for error handling on the NVIDIA Tegra 'control
backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip SoCs,
various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers
that merge updates this way:
- Various updates and new drivers in the memory controller subsystem
for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A v1.1
specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem"
* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
ARM: remove check for CONFIG_DEBUG_LL_SER3
firmware/psci: Add debugfs support to ease debugging
firmware/psci: Print a warning if PSCI doesn't accept PC mode
dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: apple: rtkit: Add apple_rtkit_poll
soc: imx: add i.MX93 media blk ctrl driver
soc: imx: add i.MX93 SRC power domain driver
soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
soc: imx: add icc paths for i.MX8MP media blk ctrl
...
Manivannan writes:
"MHI Host
--------
- Print the modem name while probing the MHI host pci-generic driver. This has
been exposed as a debug information so far but on a low storate embedded
devices such as OpenWRT based products, this helps in identifying the
attached modem without enabling the debug logs."
* tag 'mhi-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi:
bus: mhi: host: always print detected modem name
This harmless print provides a very easy way of knowing
if the modem is detected properly during probing.
Promote it to an informational print so no hassle is required
enabling kernel debugging info to obtain it.
The rationale here is that:
On a lot of low-storage embedded devices, extensive kernel
debugging info is not always present as this would
increase it's size to much causing partition size issues.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/20220831100349.1488762-1-koen.vandeputte@citymesh.com
[mani: added missing review tags]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The code to create the child platform device is essentially the same as
what platform_device_register_full() does, so change over to use
that same function to reduce duplication.
Signed-off-by: John Garry <john.garry@huawei.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The OF ID table is not guarded, and the ACPI table does not needs it either.
The IDs do not depend on the configuration. Hence drop ACPI_PTR() from the
code and move ID table closer to its user.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Use dev_fwnode() and acpi_fwnode_handle() instead of dereferencing
an fwnode handle directly, which is a better coding practice.
While at it, reuse fwnode instead of ACPI_COMPANION().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Fabio Porcedda