commit dcc7620cad upstream.
Upstream commit 98d74f9cea ("xhci: fix 10 second timeout on removal of
PCI hotpluggable xhci controllers") fixes a problem with hot pluggable PCI
xhci controllers which can result in excessive timeouts, to the point where
the system reports a deadlock.
The same problem is seen with hot pluggable xhci controllers using the
xhci-plat driver, such as the driver used for Type-C ports on rk3399.
Similar to hot-pluggable PCI controllers, the driver for this chip
removes the xhci controller from the system when the Type-C cable is
disconnected.
The solution for PCI devices works just as well for non-PCI devices
and avoids the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f95e60a7db upstream.
According to xHCI spec, HCIVERSION containing a BCD encoding
of the xHCI specification revision number, 0100h corresponds
to xHCI version 1.0. Change "100" as "0x100".
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Fixes: 04abb6de28 ("xhci: Read and parse new xhci 1.1 capability register")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5de4e1ea9a upstream.
The commit 4ac53087d6 ("usb: xhci: plat: Create both
HCDs before adding them") move add hcd to the end of
probe, this cause hcc_params uninitiated, because xHCI
driver sets hcc_params in xhci_gen_setup() called from
usb_add_hcd().
This patch checks the Maximum Primary Stream Array Size
in the hcc_params register after add primary hcd.
Signed-off-by: William wu <william.wu@rock-chips.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Fixes: 4ac53087d6 ("usb: xhci: plat: Create both HCDs before adding them")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6169d0409 upstream.
If a URB is killed while the host is removed we can end up in a situation
where the hub thread takes the roothub device lock, and waits for
the URB to be given back by xhci-hcd, blocking the host remove code.
xhci-hcd tries to stop the endpoint and give back the urb, but can't
as the host is removed from PCI bus at the same time, preventing the normal
way of giving back urb.
Instead we need to rely on the stop command timeout function to give back
the urb. This xhci_stop_endpoint_command_watchdog() timeout function
used a XHCI_STATE_DYING flag to indicate if the timeout function is already
running, but later this flag has been taking into use in other places to
mark that xhci is dying.
Remove checks for XHCI_STATE_DYING in xhci_urb_dequeue. We are still
checking that reading from pci state does not return 0xffffffff or that
host is not halted before trying to stop the endpoint.
This whole area of stopping endpoints, giving back URBs, and the wathdog
timeout need rework, this fix focuses on solving a specific deadlock
issue that we can then send to stable before any major rework.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c111b6c38 upstream.
Current abort operation has race.
xhci_handle_command_timeout()
xhci_abort_cmd_ring()
xhci_write_64(CMD_RING_ABORT)
xhci_handshake(5s)
do {
check CMD_RING_RUNNING
udelay(1)
...
COMP_CMD_ABORT event
COMP_CMD_STOP event
xhci_handle_stopped_cmd_ring()
restart cmd_ring
CMD_RING_RUNNING become 1 again
} while ()
return -ETIMEDOUT
xhci_write_64(CMD_RING_ABORT)
/* can abort random command */
To do abort operation correctly, we have to wait both of COMP_CMD_STOP
event and negation of CMD_RING_RUNNING.
But like above, while timeout handler is waiting negation of
CMD_RING_RUNNING, event handler can restart cmd_ring. So timeout
handler never be notice negation of CMD_RING_RUNNING, and retry of
CMD_RING_ABORT can abort random command (BTW, I guess retry of
CMD_RING_ABORT was workaround of this race).
To fix this race, this moves xhci_handle_stopped_cmd_ring() to
xhci_abort_cmd_ring(). And timeout handler waits COMP_CMD_STOP event.
At this point, timeout handler is owner of cmd_ring, and safely
restart cmd_ring by using xhci_handle_stopped_cmd_ring().
[FWIW, as bonus, this way would be easily extend to add CMD_RING_PAUSE
operation]
[locks edited as patch is rebased on other locking fixes -Mathias]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb4d5ce588 upstream.
This is preparation to fix abort operation race (See "xhci: Fix race
related to abort operation"). To make timeout sleepable, use
delayed_work instead of timer.
[change a newly added pending timer fix to pending work -Mathias]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dea70778c upstream.
In command timer function, xhci_handle_command_timeout(), xhci->lock
is unlocked before call into xhci_abort_cmd_ring(). This might cause
race between the timer function and the event handler.
The xhci_abort_cmd_ring() function sets the CMD_RING_ABORT bit in the
command register and polling it until the setting takes effect. A stop
command ring event might be handled between writing the abort bit and
polling for it. The event handler will restart the command ring, which
causes the failure of polling, and we ever believed that we failed to
stop it.
As a bonus, this also fixes some issues of calling functions without
locking in xhci_handle_command_timeout().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5a1b95141 upstream.
If we get a command completion event at the same time as the command
timeout work starts on another cpu we might end up aborting the wrong
command.
If the command completion takes the xhci lock before the timeout work, it
will handle the command, pick the next command, mark it as current_cmd, and
re-queue the timeout work. When the timeout work finally gets the lock
It will start aborting the wrong command.
This case can be resolved by checking if the timeout work is pending inside
the timeout function itself. A new timeout work can only be pending if the
command completed and a new command was queued.
If there are no more commands pending then command completion will set
the current_cmd to NULL, which is already handled in the timeout work.
Reported-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a7cfdf37b upstream.
When current command was supposed to be aborted, host will free the command
in handle_cmd_completion() function. But it might be still referenced by
xhci->current_cmd, which need to set NULL.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90797aee5d upstream.
xhci_setup_device() should return failure with correct error number
when xhci host has died, removed or halted.
During usb device enumeration, if usb host is not accessible (died,
removed or halted), the hc_driver->address_device() should return
a corresponding error code to usb core. But current xhci driver just
returns success. This misleads usb core to continue the enumeration
by reading the device descriptor, which will result in failure, and
users will get a misleading message like "device descriptor read/8,
error -110".
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee8665e28e upstream.
the tt_info provided by a HS hub might be in use to by a child device
Make sure we free the devices in the correct order.
This is needed in special cases such as when xhci controller is
reset when resuming from hibernate, and all virt_devices are freed.
Also free the virt_devices starting from max slot_id as children
more commonly have higher slot_id than parent.
Reported-by: Guenter Roeck <groeck@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 346e99736c upstream.
If a device is unplugged and replugged during Sx system suspend
some Intel xHC hosts will overwrite the CAS (Cold attach status) flag
and no device connection is noticed in resume.
A device in this state can be identified in resume if its link state
is in polling or compliance mode, and the current connect status is 0.
A device in this state needs to be warm reset.
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Observed on Cherryview and Apollolake as they go into compliance mode
if LFPS times out during polling, and re-plugged devices are not
discovered at resume.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b98546737 upstream.
handle_cmd_completion() frees a command structure which might be still
referenced by xhci->current_cmd.
This might cause problem when xhci->current_cmd is accessed after that.
A real-life case could be like this. The host takes a very long time to
respond to a command, and the command timer is fired at the same time
when the command completion event arrives. The command completion
handler frees xhci->current_cmd before the timer function can grab
xhci->lock. Afterward, timer function grabs the lock and go ahead with
checking and setting members of xhci->current_cmd.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccdb6be9ec upstream.
The UHCI controllers in Intel chipsets rely on a platform-specific non-PME
mechanism for wakeup signalling. They can generate wakeup signals even
though they don't support PME.
We need to let the USB core know this so that it will enable runtime
suspend for UHCI controllers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c39135aa4 upstream.
xHC in Wildcatpoint-LP PCH is similar to LynxPoint-LP and need the
same quirks to prevent machines from spurious restart while
shutting them down.
Reported-by: Hasan Mahmood <hasan.mahm@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed6d6f8f42 upstream.
Increase ohci watchout delay to 275 ms. Previous delay was 250 ms
with 20 ms of slack, after removing slack time some ohci controllers don't
respond in time. Logs from systems with controllers that have the
issue would show "HcDoneHead not written back; disabled"
Signed-off-by: Bryan Paluch <bryanpaluch@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d3b016a6f upstream.
USB2 host inititated resume, and system suspend bus resume
need to use the same USB_RESUME_TIMEOUT as elsewhere.
This resolves a device disconnect issue at system resume seen
on Intel Braswell and Apollolake, but is in no way limited to
those platforms.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcf42aa60c upstream.
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)
the ->primary_hcd will be set to NULL at USB3 hcd removal.
Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0caf6b3345 upstream.
In most cases the devices with the speed set to USB_SPEED_SUPER_PLUS
are handled like regular SuperSpeed devices.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1f6d9a8b5 upstream.
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88716a9376 upstream.
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33be126510 upstream.
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc337b5150 upstream.
In ehci_turn_off_all_ports() all EHCI port registers are cleared to zero.
On some hardware, this can lead to an system hang,
when ehci_port_power() accesses the already cleared registers.
This patch changes the order of cleanup.
First call ehci_port_power() which respects the current bits in
port status registers
and afterwards cleanup the hard way by setting everything to zero.
Signed-off-by: Marc Ohlf <ohlf@mkt-sys.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c66f59ee50 upstream.
Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.
This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.
The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.
Fix ed_schedule to update ED state only on successful return.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8a15a9650 upstream.
There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.
Commit a47cc24cd1 ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.
This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.
Fixes: a47cc24cd1 ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3425aa03f4 upstream.
If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.
If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.
There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.
The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.
Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d95815ba6a upstream.
I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.
Tests on another motherboard show that it does work with streams disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de95c40d5b upstream.
On some platforms, the clocks might be registered by a platform
driver. When this is the case, the clock platform driver may very well
be probed after xhci-plat, in which case the first probe() invocation
of xhci-plat will receive -EPROBE_DEFER as the return value of
devm_clk_get().
The current code handles that as a normal error, and simply assumes
that this means that the system doesn't have a clock for the XHCI
controller, and continues probing without calling
clk_prepare_enable(). Unfortunately, this doesn't work on systems
where the XHCI controller does have a clock, but that clock is
provided by another platform driver. In order to fix this situation,
we handle the -EPROBE_DEFER error condition specially, and abort the
XHCI controller probe(). It will be retried later automatically, the
clock will be available, devm_clk_get() will succeed, and the probe()
will continue with the clock prepared and enabled as expected.
In practice, such issue is seen on the ARM64 Marvell 7K/8K platform,
where the clocks are registered by a platform driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27a41a83ec upstream.
Under stress occasions some TI devices might not return early when
reading the status register during the quirk invocation of xhci_irq made
by usb_hcd_pci_remove. This means that instead of returning, we end up
handling this interruption in the middle of a shutdown. Since
xhci->event_ring has already been freed in xhci_mem_cleanup, we end up
accessing freed memory, causing the Oops below.
commit 8c24d6d7b0 ("usb: xhci: stop everything on the first call to
xhci_stop") is the one that changed the instant in which we clean up the
event queue when stopping a device. Before, we didn't call
xhci_mem_cleanup at the first time xhci_stop is executed (for the shared
HCD), instead, we only did it after the invocation for the primary HCD,
much later at the removal path. The code flow for this oops looks like
this:
xhci_pci_remove()
usb_remove_hcd(xhci->shared)
xhci_stop(xhci->shared)
xhci_halt()
xhci_mem_cleanup(xhci); // Free the event_queue
usb_hcd_pci_remove(primary)
xhci_irq() // Access the event_queue if STS_EINT is set. Crash.
xhci_stop()
xhci_halt()
// return early
The fix modifies xhci_stop to only cleanup the xhci data when releasing
the primary HCD. This way, we still have the event_queue configured
when invoking xhci_irq. We still halt the device on the first call to
xhci_stop, though.
I could reproduce this issue several times on the mainline kernel by
doing a bind-unbind stress test with a specific storage gadget attached.
I also ran the same test over-night with my patch applied and didn't
observe the issue anymore.
[ 113.334124] Unable to handle kernel paging request for data at address 0x00000028
[ 113.335514] Faulting instruction address: 0xd00000000d4f767c
[ 113.336839] Oops: Kernel access of bad area, sig: 11 [#1]
[ 113.338214] SMP NR_CPUS=1024 NUMA PowerNV
[c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80
[c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0
[c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0
[xhci_pci]
[c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110
[c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190
[c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70
[c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150
[c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0
[c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0
[c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0
[c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190
[c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200
[c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110
[c000000efe47be30] c000000000009260 system_call+0x38/0x108
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: joel@jms.id.au
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98d74f9cea upstream.
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 671ffdff5b upstream.
Give USB3 devices a better chance to enumerate at USB 3 speeds if
they are connected to a suspended host.
Solves an issue with NEC uPD720200 host hanging when partially
enumerating a USB3 device as USB2 after host controller runtime resume.
Tested-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c82171167 upstream.
xhci driver frees data for all devices, both usb2 and and usb3 the
first time usb_remove_hcd() is called, including td_list and and xhci_ring
structures.
When usb_remove_hcd() is called a second time for the second xhci bus it
will try to dequeue all pending urbs, and touches td_list which is already
freed for that endpoint.
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a683509071 upstream.
This reverts commit e210c422b6 ("xhci: don't finish a TD if we get a
short transfer event mid TD")
Turns out that most host controllers do not follow the xHCI specs and never
send the second event for the last TRB in the TD if there was a short event
mid-TD.
Returning the URB directly after the first short-transfer event is far
better than never returning the URB. (class drivers usually timeout
after 30sec). For the hosts that do send the second event we will go
back to treating it as misplaced event and print an error message for it.
The origial patch was sent to stable kernels and needs to be reverted from
there as well
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa89537783 upstream.
Commit abce329c27 ("xhci: Workaround to get D3 working in Intel xHCI")
adds a workaround for a limitation of PME storm caused by SSIC port in
some Intel SoCs. This commit only handled one SSIC port, while there
are actually two SSIC ports in the chips. This patch handles both SSIC
ports. Without this fix, users still see PME storm.
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Cc: stable <stable@vger.kernel.org>
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a memory leak because acpi_evaluate_dsm() actually returns an
object which the caller is supposed to release. Fix this by calling
ACPI_FREE() for the returned object (this expands to kfree() so passing
NULL there is fine as well).
While there correct indentation in !CONFIG_ACPI case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.2
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qset_fill_page_list() do not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear device initiated resume variables once device is fully up and running
in U0 state.
Resume needs to be signaled for 20ms for usb2 devices before they can be
moved to U0 state.
An interrupt is triggered if a device initiates resume. As we handle the
event in interrupt context we can not sleep for 20ms, so we instead set
a resume flag, a timestamp, and start the roothub polling.
The roothub code will later move the port to U0 when it finds a port in
resume state with the resume flag set, and timestamp passed by 20ms.
A host initiated resume is however not done in interrupt context, and
host initiated resume code will directly signal resume, wait 20ms and then
move the port to U0.
These two codepaths can race, if we are in the middle of a host initated
resume, while sleeping for 20ms, we may handle a port event and find the
port in resume state. The port event handling code will assume the resume
was device initiated and set the resume flag and timestamp.
Root hub code will however not catch the port in resume state again as the
host initated resume code has already moved the port to U0.
The resume flag and timestamp will remain set for this port preventing port
from suspending again (LPM setting port to U3)
Fix this for now by always clearing the device initated resume parameters
once port is in U0
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function ep_ring_is_processing() checks the dequeue pointer
in endpoint context to know whether an endpoint is busy with
processing TRBs. This is not correct since dequeue pointer
field in an endpoint context is only valid when the endpoint
is in Halted or Stopped states. This buggy code causes audio
noise when playing sound with USB headset connected to host
controllers which support CFC (one of xhci 1.1 features).
This patch should exist in stable kernel since v4.3.
Reported-and-tested-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge second patch-bomb from Andrew Morton:
- most of the rest of MM
- procfs
- lib/ updates
- printk updates
- bitops infrastructure tweaks
- checkpatch updates
- nilfs2 update
- signals
- various other misc bits: coredump, seqfile, kexec, pidns, zlib, ipc,
dma-debug, dma-mapping, ...
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (102 commits)
ipc,msg: drop dst nil validation in copy_msg
include/linux/zutil.h: fix usage example of zlib_adler32()
panic: release stale console lock to always get the logbuf printed out
dma-debug: check nents in dma_sync_sg*
dma-mapping: tidy up dma_parms default handling
pidns: fix set/getpriority and ioprio_set/get in PRIO_USER mode
kexec: use file name as the output message prefix
fs, seqfile: always allow oom killer
seq_file: reuse string_escape_str()
fs/seq_file: use seq_* helpers in seq_hex_dump()
coredump: change zap_threads() and zap_process() to use for_each_thread()
coredump: ensure all coredumping tasks have SIGNAL_GROUP_COREDUMP
signal: remove jffs2_garbage_collect_thread()->allow_signal(SIGCONT)
signal: introduce kernel_signal_stop() to fix jffs2_garbage_collect_thread()
signal: turn dequeue_signal_lock() into kernel_dequeue_signal()
signals: kill block_all_signals() and unblock_all_signals()
nilfs2: fix gcc uninitialized-variable warnings in powerpc build
nilfs2: fix gcc unused-but-set-variable warnings
MAINTAINERS: nilfs2: add header file for tracing
nilfs2: add tracepoints for analyzing reading and writing metadata files
...
Guenter Roeck