commit c130b666a9 upstream.
Commit f209fa03fc ("serial: 8250_pci: Detach low-level driver during
PCI error recovery") introduces a potential use-after-free in case the
pciserial_init_ports call in serial8250_io_resume fails, which may
happen if a memory allocation fails or if the .init quirk failed for
whatever reason). If this happen, further pci_get_drvdata will return a
pointer to freed memory.
This patch reworks the PCI recovery resume hook to restore the old priv
structure in this case, which should be ok, since the ports were already
detached. Such error during recovery causes us to give up on the
recovery.
Fixes: f209fa03fc ("serial: 8250_pci: Detach low-level driver during PCI error recovery")
Reported-by: Michal Suchanek <msuchanek@suse.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4f642a8a3 upstream.
The nozomi wireless data driver has its own helper function to
transfer data from a FIFO, doing an extra byte swap on big-endian
architectures, presumably to bring the data back into byte-serial
order after readw() or readl() perform their implicit byteswap.
This helper function is used in the receive_data() function to
first read the length into a 32-bit variable, which causes
a compile-time warning:
drivers/tty/nozomi.c: In function 'receive_data':
drivers/tty/nozomi.c:857:9: warning: 'size' may be used uninitialized in this function [-Wmaybe-uninitialized]
The problem is that gcc is unsure whether the data was actually
read or not. We know that it is at this point, so we can replace
it with a single readl() to shut up that warning.
I am leaving the byteswap in there, to preserve the existing
behavior, even though this seems fishy: Reading the length of
the data into a cpu-endian variable should normally not use
a second byteswap on big-endian systems, unless the hardware
is aware of the CPU endianess.
There appears to be a lot more confusion about endianess in this
driver, so it probably has not worked on big-endian systems in
a long time, if ever, and I have no way to test it. It's well
possible that this driver has not been used by anyone in a while,
the last patch that looks like it was tested on the hardware is
from 2008.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b389f173aa upstream.
When using RS485 in half duplex, RX should be enabled when TX is
finished, and stopped when TX starts.
Before commit 0058f0871e ("tty/serial: atmel: fix RS485 half
duplex with DMA"), RX was not disabled in atmel_start_tx() if the DMA
was used. So, collisions could happened.
But disabling RX in atmel_start_tx() uncovered another bug:
RX was enabled again in the wrong place (in atmel_tx_dma) instead of
being enabled when TX is finished (in atmel_complete_tx_dma), so the
transmission simply stopped.
This bug was not triggered before commit 0058f0871e
("tty/serial: atmel: fix RS485 half duplex with DMA") because RX was
never disabled before.
Moving atmel_start_rx() in atmel_complete_tx_dma() corrects the problem.
Reported-by: Gil Weber <webergil@gmail.com>
Fixes: 0058f0871e
Tested-by: Gil Weber <webergil@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Bryan Evenson <bevenson@melinkcorp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 497e1e16f4 upstream.
A side effect of 89d8232411 ("tty/serial: atmel_serial: BUG: stop DMA
from transmitting in stop_tx") is that the console can be called with
TX path disabled. Then the system would hang trying to push charecters
out in atmel_console_putchar().
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 89d8232411 ("tty/serial: atmel_serial: BUG: stop DMA from transmitting in stop_tx")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31ca2c63fd upstream.
If uart_flush_buffer() is called between atmel_tx_dma() and
atmel_complete_tx_dma(), the circular buffer has been cleared, but not
atmel_port->tx_len.
That leads to a circular buffer overflow (dumping (UART_XMIT_SIZE -
atmel_port->tx_len) bytes).
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
[ Upstream commit f209fa03fc ]
During a PCI error recovery, like the ones provoked by EEH in the ppc64
platform, all IO to the device must be blocked while the recovery is
completed. Current 8250_pci implementation only suspends the port
instead of detaching it, which doesn't prevent incoming accesses like
TIOCMGET and TIOCMSET calls from reaching the device. Those end up
racing with the EEH recovery, crashing it. Similar races were also
observed when opening the device and when shutting it down during
recovery.
This patch implements a more robust IO blockage for the 8250_pci
recovery by unregistering the port at the beginning of the procedure and
re-adding it afterwards. Since the port is detached from the uart
layer, we can be sure that no request will make through to the device
during recovery. This is similar to the solution used by the JSM serial
driver.
I thank Peter Hurley <peter@hurleysoftware.com> for valuable input on
this one over one year ago.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f98c7bce57 upstream.
If DMA is not available (even when configured in DeviceTree), the driver
will fail the startup procedure thus making serial console not
available.
For example this causes boot failure on QEMU ARMv7 (Exynos4210, SMDKC210):
[ 1.302575] OF: amba_device_add() failed (-19) for /amba/pdma@12680000
...
[ 11.435732] samsung-uart 13800000.serial: DMA request failed
[ 72.963893] samsung-uart 13800000.serial: DMA request failed
[ 73.143361] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000000
DMA is not necessary for serial to work, so continue with UART startup
after emitting a warning.
Fixes: 62c37eedb7 ("serial: samsung: add dma reqest/release functions")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c9c858e2f upstream.
The MKS Instruments SCOM-0800 and SCOM-0801 cards (originally by Tenta
Technologies) are 3U CompactPCI serial cards with 4 and 8 serial ports,
respectively. The first 4 ports are implemented by an OX16PCI954 chip,
and the second 4 ports are implemented by an OX16C954 chip on a local
bus, bridged by the second PCI function of the OX16PCI954. The ports
are jumper-selectable as RS-232 and RS-422/485, and the UARTs use a
non-standard oscillator frequency of 20 MHz (base_baud = 1250000).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82f2341c94 upstream.
Currently N_HDLC line discipline uses a self-made singly linked list for
data buffers and has n_hdlc.tbuf pointer for buffer retransmitting after
an error.
The commit be10eb7589
("tty: n_hdlc add buffer flushing") introduced racy access to n_hdlc.tbuf.
After tx error concurrent flush_tx_queue() and n_hdlc_send_frames() can put
one data buffer to tx_free_buf_list twice. That causes double free in
n_hdlc_release().
Let's use standard kernel linked list and get rid of n_hdlc.tbuf:
in case of tx error put current data buffer after the head of tx_buf_list.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9b736d88a upstream.
The class of 4 n_hdls buf locks is the same because a single function
n_hdlc_buf_list_init is used to init all the locks. But since
flush_tx_queue takes n_hdlc->tx_buf_list.spinlock and then calls
n_hdlc_buf_put which takes n_hdlc->tx_free_buf_list.spinlock, lockdep
emits a warning:
=============================================
[ INFO: possible recursive locking detected ]
4.3.0-25.g91e30a7-default #1 Not tainted
---------------------------------------------
a.out/1248 is trying to acquire lock:
(&(&list->spinlock)->rlock){......}, at: [<ffffffffa01fd020>] n_hdlc_buf_put+0x20/0x60 [n_hdlc]
but task is already holding lock:
(&(&list->spinlock)->rlock){......}, at: [<ffffffffa01fdc07>] n_hdlc_tty_ioctl+0x127/0x1d0 [n_hdlc]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&list->spinlock)->rlock);
lock(&(&list->spinlock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by a.out/1248:
#0: (&tty->ldisc_sem){++++++}, at: [<ffffffff814c9eb0>] tty_ldisc_ref_wait+0x20/0x50
#1: (&(&list->spinlock)->rlock){......}, at: [<ffffffffa01fdc07>] n_hdlc_tty_ioctl+0x127/0x1d0 [n_hdlc]
...
Call Trace:
...
[<ffffffff81738fd0>] _raw_spin_lock_irqsave+0x50/0x70
[<ffffffffa01fd020>] n_hdlc_buf_put+0x20/0x60 [n_hdlc]
[<ffffffffa01fdc24>] n_hdlc_tty_ioctl+0x144/0x1d0 [n_hdlc]
[<ffffffff814c25c1>] tty_ioctl+0x3f1/0xe40
...
Fix it by initializing the spin_locks separately. This removes also
reduntand memset of a freshly kzallocated space.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abe81f3b8e upstream.
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/tty/serial/msm_serial.ko | grep alias
$
After this patch:
$ modinfo drivers/tty/serial/msm_serial.ko | grep alias
alias: of:N*T*Cqcom,msm-uartdmC*
alias: of:N*T*Cqcom,msm-uartdm
alias: of:N*T*Cqcom,msm-uartC*
alias: of:N*T*Cqcom,msm-uart
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 802c03881f upstream.
The sysrq input handler should be attached to the input device which has
a left alt key.
On 32-bit kernels, some input devices which has a left alt key cannot
attach sysrq handler. Because the keybit bitmap in struct input_device_id
for sysrq is not correctly initialized. KEY_LEFTALT is 56 which is
greater than BITS_PER_LONG on 32-bit kernels.
I found this problem when using a matrix keypad device which defines
a KEY_LEFTALT (56) but doesn't have a KEY_O (24 == 56%32).
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89d8232411 upstream.
If we don't disable the transmitter in atmel_stop_tx, the DMA buffer
continues to send data until it is emptied.
This cause problems with the flow control (CTS is asserted and data are
still sent).
So, disabling the transmitter in atmel_stop_tx is a sane thing to do.
Tested on at91sam9g35-cm(DMA)
Tested for regressions on sama5d2-xplained(Fifo) and at91sam9g20ek(PDC)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04da73803c upstream.
The use of IRQF_ONESHOT when registering an interrupt handler with
request_irq() is non-sensical.
Not only that, it also prevents the handler from being threaded when it
otherwise should be w/ IRQ_FORCED_THREADING is enabled. This causes the
following deadlock observed by Sean Nyekjaer on -rt:
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[..]
rt_spin_lock_slowlock from queue_kthread_work
queue_kthread_work from sc16is7xx_irq
sc16is7xx_irq [sc16is7xx] from handle_irq_event_percpu
handle_irq_event_percpu from handle_irq_event
handle_irq_event from handle_level_irq
handle_level_irq from generic_handle_irq
generic_handle_irq from mxc_gpio_irq_handler
mxc_gpio_irq_handler from mx3_gpio_irq_handler
mx3_gpio_irq_handler from generic_handle_irq
generic_handle_irq from __handle_domain_irq
__handle_domain_irq from gic_handle_irq
gic_handle_irq from __irq_svc
__irq_svc from rt_spin_unlock
rt_spin_unlock from kthread_worker_fn
kthread_worker_fn from kthread
kthread from ret_from_fork
Fixes: 9e6f4ca3e5 ("sc16is7xx: use kthread_worker for tx_work and irq")
Reported-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Josh Cartwright <joshc@ni.com>
Cc: linux-rt-users@vger.kernel.org
Cc: Jakub Kicinski <moorray3@wp.pl>
Cc: linux-serial@vger.kernel.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31b5929d53 upstream.
There is a disagreement between drivers/tty/vt/keyboard.c and
drivers/input/input-leds.c with regard to what is a Scroll Lock LED
trigger name: input calls it "kbd-scrolllock", but vt calls it
"kbd-scrollock" (two l's).
This prevents Scroll Lock LED trigger from binding to this LED by default.
Since it is a scroLL Lock LED, this interface was introduced only about a
year ago and in an Internet search people seem to reference this trigger
only to set it to this LED let's simply rename it to "kbd-scrolllock".
Also, it looks like this was supposed to be changed before this code was
merged: https://lkml.org/lkml/2015/6/9/697 but it was done only on
the input side.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 344e3c7734 ]
We accidentally take the "port->lock" twice in a row. This old code
was supposed to be deleted.
Fixes: e58e241c17 ('sparc: serial: Clean up the locking for -rt')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bcffe7575 upstream.
After commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), the hardware handshake wasn't
functional anymore on Atmel platforms (beside SAMA5D2).
To understand why, one has to understand the flag ATMEL_US_USMODE_HWHS
first:
Before commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), this flag was never set.
Thus, the CTS/RTS where only handled by serial_core (and everything
worked just fine).
This commit introduced the use of the ATMEL_US_USMODE_HWHS flag,
enabling it for all boards when the user space enables flow control.
When the ATMEL_US_USMODE_HWHS is set, the Atmel USART controller
handles a part of the flow control job:
- disable the transmitter when the CTS pin gets high.
- drive the RTS pin high when the DMA buffer transfer is completed or
PDC RX buffer full or RX FIFO is beyond threshold. (depending on the
controller version).
NB: This feature is *not* mandatory for the flow control to work.
(Nevertheless, it's very useful if low latencies are needed.)
Now, the specifics of the ATMEL_US_USMODE_HWHS flag:
- For platforms with DMAC and no FIFOs (sam9x25, sam9x35, sama5D3,
sama5D4, sam9g15, sam9g25, sam9g35)* this feature simply doesn't work.
( source: https://lkml.org/lkml/2016/9/7/598 )
Tested it on sam9g35, the RTS pins always stays up, even when RXEN=1
or a new DMA transfer descriptor is set.
=> ATMEL_US_USMODE_HWHS must not be used for those platforms
- For platforms with a PDC (sam926{0,1,3}, sam9g10, sam9g20, sam9g45,
sam9g46)*, there's another kind of problem. Once the flag
ATMEL_US_USMODE_HWHS is set, the RTS pin can't be driven anymore via
RTSEN/RTSDIS in USART Control Register. The RTS pin can only be driven
by enabling/disabling the receiver or setting RCR=RNCR=0 in the PDC
(Receive (Next) Counter Register).
=> Doing this is beyond the scope of this patch and could add other
bugs, so the original (and working) behaviour should be set for those
platforms (meaning ATMEL_US_USMODE_HWHS flag should be unset).
- For platforms with a FIFO (sama5d2)*, the RTS pin is driven according
to the RX FIFO thresholds, and can be also driven by RTSEN/RTSDIS in
USART Control Register. No problem here.
(This was the use case of commit 1cf6e8fc83 ("tty/serial: at91: fix
RTS line management when hardware handshake is enabled"))
NB: If the CTS pin declared as a GPIO in the DTS, (for instance
cts-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_LOW>), the transmitter will be
disabled.
=> ATMEL_US_USMODE_HWHS flag can be set for this platform ONLY IF the
CTS pin is not a GPIO.
So, the only case when ATMEL_US_USMODE_HWHS can be enabled is when
(atmel_use_fifo(port) &&
!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
Tested on all Atmel USART controller flavours:
AT91SAM9G35-CM (DMAC flavour), AT91SAM9G20-EK (PDC flavour),
SAMA5D2xplained (FIFO flavour).
* the list may not be exhaustive
Fixes: 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[nicolas.ferre@atmel.com: adapt to 4.4.x kernel for stable by adding
the atmel_port variable declaration which was missing]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42acfc6615 upstream.
In csi_J(3), the third parameter of scr_memsetw (vc_screenbuf_size) is
divided by 2 inappropriatelly. But scr_memsetw expects size, not
count, because it divides the size by 2 on its own before doing actual
memset-by-words.
So remove the bogus division.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Petr Písař <ppisar@redhat.com>
Fixes: f8df13e0a9 (tty: Clean console safely)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8d192428f upstream.
Added devices ids for acces i/o products quad and octal serial cards
that make use of existing Pericom PI7C9X7954 and PI7C9X7958
configurations .
Signed-off-by: Jimi Damon <jdamon@accesio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47b34d2ef2 upstream.
Since the commit c1a67b48f6 ("serial: 8250_pci: replace switch-case by
formula for Intel MID"), the 8250 driver crashes in the byt_set_termios()
function with a divide error. This is caused by the fact that a baud rate of 0
(B0) is not handled properly. Fix it by falling back to B9600 in this case.
Reported-by: "Mendez Salinas, Fernando" <fernando.mendez.salinas@intel.com>
Fixes: c1a67b48f6 ("serial: 8250_pci: replace switch-case by formula for Intel MID")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e51e4d8a18 upstream.
When the clk_get() of "uart" clock returns EPROBE_DEFER, the next re-probe
finishes with success but uses invalid (ERR_PTR) values. This leads to
dereferencing of ERR_PTR stored under ourport->clk:
12c30000.serial: Controller clock not found
(...)
12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10
Unable to handle kernel paging request at virtual address fffffdfb
(clk_prepare) from [<c039f7d0>] (s3c24xx_serial_pm+0x20/0x128)
(s3c24xx_serial_pm) from [<c0395414>] (uart_change_pm+0x38/0x40)
(uart_change_pm) from [<c039689c>] (uart_add_one_port+0x31c/0x44c)
(uart_add_one_port) from [<c03a035c>] (s3c24xx_serial_probe+0x2a8/0x418)
(s3c24xx_serial_probe) from [<c03ee110>] (platform_drv_probe+0x50/0xb0)
(platform_drv_probe) from [<c03ecb44>] (driver_probe_device+0x1f4/0x2b0)
(driver_probe_device) from [<c03eb0c0>] (bus_for_each_drv+0x44/0x8c)
(bus_for_each_drv) from [<c03ec8c8>] (__device_attach+0x9c/0x100)
(__device_attach) from [<c03ebf54>] (bus_probe_device+0x84/0x8c)
(bus_probe_device) from [<c03ec388>] (deferred_probe_work_func+0x60/0x8c)
(deferred_probe_work_func) from [<c012fee4>] (process_one_work+0x120/0x328)
(process_one_work) from [<c0130150>] (worker_thread+0x2c/0x4ac)
(worker_thread) from [<c0135320>] (kthread+0xd8/0xf4)
(kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
The first unsuccessful clk_get() causes s3c24xx_serial_init_port() to
exit with failure but the s3c24xx_uart_port is left half-configured
(e.g. port->mapbase is set, clk contains ERR_PTR). On next re-probe,
the function s3c24xx_serial_init_port() will exit early with success
because of configured port->mapbase and driver will use old values,
including the ERR_PTR as clock.
Fix this by cleaning the port->mapbase on error path so each re-probe
will initialize all of the port settings.
Fixes: 60e9357547 ("serial: samsung: enable clock before clearing pending interrupts during init")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30acf549ca upstream.
For dm uarts in pio mode tx data is transferred to the fifo register 4
bytes at a time, but care is not taken when these 4 bytes spans the end
of the xmit buffer so the loop might read up to 3 bytes past the buffer
and then skip the actual data at the beginning of the buffer.
Fix this by, analogous to the DMA case, make sure the chunk doesn't
wrap the xmit buffer.
Fixes: 3a878c430f ("tty: serial: msm: Add TX DMA support")
Cc: Ivan Ivanov <iivanov.xz@gmail.com>
Reported-by: Frank Rowand <frowand.list@gmail.com>
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Frank Rowand <frank.rowand@am.sony.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67245ff332 upstream.
This gets rid of the horrible notion of having that
struct inode *ptmx_inode
be the linchpin of the interface between the pty code and devpts.
By de-emphasizing the ptmx inode, a lot of things actually get cleaner,
and we will have a much saner way forward. In particular, this will
allow us to associate with any particular devpts instance at open-time,
and not be artificially tied to one particular ptmx inode.
The patch itself is actually fairly straightforward, and apart from some
locking and return path cleanups it's pretty mechanical:
- the interfaces that devpts exposes all take "struct pts_fs_info *"
instead of "struct inode *ptmx_inode" now.
NOTE! The "struct pts_fs_info" thing is a completely opaque structure
as far as the pty driver is concerned: it's still declared entirely
internally to devpts. So the pty code can't actually access it in any
way, just pass it as a "cookie" to the devpts code.
- the "look up the pts fs info" is now a single clear operation, that
also does the reference count increment on the pts superblock.
So "devpts_add/del_ref()" is gone, and replaced by a "lookup and get
ref" operation (devpts_get_ref(inode)), along with a "put ref" op
(devpts_put_ref()).
- the pty master "tty->driver_data" field now contains the pts_fs_info,
not the ptmx inode.
- because we don't care about the ptmx inode any more as some kind of
base index, the ref counting can now drop the inode games - it just
gets the ref on the superblock.
- the pts_fs_info now has a back-pointer to the super_block. That's so
that we can easily look up the information we actually need. Although
quite often, the pts fs info was actually all we wanted, and not having
to look it up based on some magical inode makes things more
straightforward.
In particular, now that "devpts_get_ref(inode)" operation should really
be the *only* place we need to look up what devpts instance we're
associated with, and we do it exactly once, at ptmx_open() time.
The other side of this is that one ptmx node could now be associated
with multiple different devpts instances - you could have a single
/dev/ptmx node, and then have multiple mount namespaces with their own
instances of devpts mounted on /dev/pts/. And that's all perfectly sane
in a model where we just look up the pts instance at open time.
This will eventually allow us to get rid of our odd single-vs-multiple
pts instance model, but this patch in itself changes no semantics, only
an internal binding model.
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jann@thejh.net>
Cc: Greg KH <greg@kroah.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Florian Weimer <fw@deneb.enyo.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Francesco Ruggeri <fruggeri@arista.com>
Cc: "Herton R. Krzesinski" <herton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 510cccb5b0 upstream.
The size of individual keymap in drivers/tty/vt/keyboard.c is NR_KEYS,
which is currently 256, whereas number of keys/buttons in input device (and
therefor in key_down) is much larger - KEY_CNT - 768, and that can cause
out-of-bound access when we do
sym = U(key_maps[0][k]);
with large 'k'.
To fix it we should not attempt iterating beyond smaller of NR_KEYS and
KEY_CNT.
Also while at it let's switch to for_each_set_bit() instead of open-coding
it.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b45996d2e upstream.
We are getting somewhat random soft lockups with this signature:
[ 86.992215] [<fffffc00080935e0>] el1_irq+0xa0/0x10c
[ 86.997082] [<fffffc000841822c>] cursor_timer_handler+0x30/0x54
[ 87.002991] [<fffffc000810ec44>] call_timer_fn+0x54/0x1a8
[ 87.008378] [<fffffc000810ef88>] run_timer_softirq+0x1c4/0x2bc
[ 87.014200] [<fffffc000809077c>] __do_softirq+0x114/0x344
[ 87.019590] [<fffffc00080af45c>] irq_exit+0x74/0x98
[ 87.024458] [<fffffc00080fac20>] __handle_domain_irq+0x98/0xfc
[ 87.030278] [<fffffc000809056c>] gic_handle_irq+0x94/0x190
This is caused by the vt visual_init() function calling into
fbcon_init() with a vc_cur_blink_ms value of zero. This is a
transient condition, as it is later set to a non-zero value. But, if
the timer happens to expire while the blink rate is zero, it goes into
an endless loop, and we get soft lockup.
The fix is to initialize vc_cur_blink_ms before calling the con_init()
function.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11ca2b7ab4 upstream.
New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart.
So add it.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8995f527a upstream.
This patch fixes the broken serial log when changing the clock source
of uart device. Before disabling the original clock source, this patch
enables the new clock source to protect the clock off state for a split second.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
commit c42850f1ae upstream.
There is a special register that shows interrupt status by source. In
particular case the source can be a combination of DMA Tx, DMA Rx, and UART.
Read the register and call the handlers only for sources that request an
interrupt.
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 107e15fc1f upstream.
Unlike Intel Medfield and Tangier platforms DNV uses PCI BAR0 for IO compatible
resources and BAR1 for MMIO. We need latter in a way to support DMA. Introduce
an additional field in the internal structure and pass PCI BAR based on device
ID.
Reported-by: "Lai, Poey Seng" <poey.seng.lai@intel.com>
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f210c18c1 upstream.
Since commit 21947ba654 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Fixes: 21947ba654 ("serial: 8250_pci: replace switch-case by formula")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5be605ac9a upstream.
Commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when
hardware handshake is enabled") actually allowed to enable hardware
handshaking.
Before, the CRTSCTS flags was silently ignored.
As the DMA controller can't drive RTS (as explain in the commit message).
Ensure that hardware flow control stays disabled when DMA is used and FIFOs
are not available.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d175feca89 upstream.
Dmitry reported, that the current cleanup code in n_gsm can trigger a
warning:
WARNING: CPU: 2 PID: 24238 at drivers/tty/n_gsm.c:2048 gsm_cleanup_mux+0x166/0x6b0()
...
Call Trace:
...
[<ffffffff81247ab9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:490
[<ffffffff828d0456>] gsm_cleanup_mux+0x166/0x6b0 drivers/tty/n_gsm.c:2048
[<ffffffff828d4d87>] gsmld_open+0x5b7/0x7a0 drivers/tty/n_gsm.c:2386
[<ffffffff828b9078>] tty_ldisc_open.isra.2+0x78/0xd0 drivers/tty/tty_ldisc.c:447
[<ffffffff828b973a>] tty_set_ldisc+0x1ca/0xa70 drivers/tty/tty_ldisc.c:567
[< inline >] tiocsetd drivers/tty/tty_io.c:2650
[<ffffffff828a14ea>] tty_ioctl+0xb2a/0x2140 drivers/tty/tty_io.c:2883
...
But this is a legal path when open fails to find a space in the
gsm_mux array and tries to clean up. So make it a standard test
instead of a warning.
Reported-by: "Dmitry Vyukov" <dvyukov@google.com>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/CACT4Y+bHQbAB68VFi7Romcs-Z9ZW3kQRvcq+BvHH1oa5NcAdLA@mail.gmail.com
Fixes: 5a640967 ("tty/n_gsm.c: fix a memory leak in gsmld_open()")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6798df4c5f upstream.
When csw->con_startup() fails in do_register_con_driver, we return no
error (i.e. 0). This was changed back in 2006 by commit 3e795de763.
Before that we used to return -ENODEV.
So fix the return value to be -ENODEV in that case again.
Fixes: 3e795de763 ("VT binding: Add binding/unbinding support for the VT console")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: "Dan Carpenter" <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff1cab374a upstream.
The BSP team noticed that there is spin/mutex lock issue on sh-sci when
CPUFREQ is used. The issue is that the notifier function may call
mutex_lock() while the spinlock is held, which can lead to a BUG().
This may happen if CPUFREQ is changed while another CPU calls
clk_get_rate().
Taking the spinlock was added to the notifier function in commit
e552de2413 ("sh-sci: add platform device private data"), to
protect the list of serial ports against modification during traversal.
At that time the Common Clock Framework didn't exist yet, and
clk_get_rate() just returned clk->rate without taking a mutex.
Note that since commit d535a2305f ("serial: sh-sci: Require a
device per port mapping."), there's no longer a list of serial ports to
traverse, and taking the spinlock became superfluous.
To fix the issue, just remove the cpufreq notifier:
1. The notifier doesn't work correctly: all it does is update stored
clock rates; it does not update the divider in the hardware.
The divider will only be updated when calling sci_set_termios().
I believe this was broken back in 2004, when the old
drivers/char/sh-sci.c driver (where the notifier did update the
divider) was replaced by drivers/serial/sh-sci.c (where the
notifier just updated port->uartclk).
Cfr. full-history-linux commits 6f8deaef2e9675d9 ("[PATCH] sh: port
sh-sci driver to the new API") and 3f73fe878dc9210a ("[PATCH]
Remove old sh-sci driver").
2. On modern SoCs, the sh-sci parent clock rate is no longer related
to the CPU clock rate anyway, so using a cpufreq notifier is
futile.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b41ce9910 upstream.
Some UART HW has a single register combining UART_DLL/UART_DLM
(this was probably forgotten in the change that introduced the
callbacks, commit b32b19b8ff)
Fixes: b32b19b8ff ("[SERIAL] 8250: set divisor register correctly ...")
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 308bbc9ab8 upstream.
The omap-serial driver emulates RS485 delays using software timers,
but neglects to clamp the input values from the unprivileged
ioctl(TIOCSRS485). Because the software implementation busy-waits,
malicious userspace could stall the cpu for ~49 days.
Clamp the input values to < 100ms.
Fixes: 4a0ac0f55b ("OMAP: add RS485 support")
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c55d9b983 upstream.
Some recent (early 2015) macbooks have Intel Broadwell where LPSS UARTs are
PCI enumerated instead of ACPI. The LPSS UART block is pretty much same as
used on Intel Baytrail so we can reuse the existing Baytrail setup code.
Add both Broadwell LPSS UART ports to the list of supported devices.
Signed-off-by: Leif Liddy <leif.liddy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dde55787b upstream.
WCH382 2S board is a PCIe card with 2 DB9 COM ports detected as
Serial controller: Device 1c00:3253 (rev 10) (prog-if 05 [16850])
Signed-off-by: Jeremy McNicoll <jmcnicol@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f55c718c2 upstream.
Considering current pty code and multiple devpts instances, it's possible
to umount a devpts file system while a program still has /dev/tty opened
pointing to a previosuly closed pty pair in that instance. In the case all
ptmx and pts/N files are closed, umount can be done. If the program closes
/dev/tty after umount is done, devpts_kill_index will use now an invalid
super_block, which was already destroyed in the umount operation after
running ->kill_sb. This is another "use after free" type of issue, but now
related to the allocated super_block instance.
To avoid the problem (warning at ida_remove and potential crashes) for
this specific case, I added two functions in devpts which grabs additional
references to the super_block, which pty code now uses so it makes sure
the super block structure is still valid until pty shutdown is done.
I also moved the additional inode references to the same functions, which
also covered similar case with inode being freed before /dev/tty final
close/shutdown.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2831c89f42 upstream.
This change fixes a bug for a corner case where we have the the last
release from a pty master/slave coming from a previously opened /dev/tty
file. When this happens, the tty->driver_data can be stale, due to all
ptmx or pts/N files having already been closed before (and thus the inode
related to these files, which tty->driver_data points to, being already
freed/destroyed).
The fix here is to keep a reference on the opened master ptmx inode.
We maintain the inode referenced until the final pty_unix98_shutdown,
and only pass this inode to devpts_kill_index.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c17c861a3 upstream.
ioctl(TIOCGETD) retrieves the line discipline id directly from the
ldisc because the line discipline id (c_line) in termios is untrustworthy;
userspace may have set termios via ioctl(TCSETS*) without actually
changing the line discipline via ioctl(TIOCSETD).
However, directly accessing the current ldisc via tty->ldisc is
unsafe; the ldisc ptr dereferenced may be stale if the line discipline
is changing via ioctl(TIOCSETD) or hangup.
Wait for the line discipline reference (just like read() or write())
to retrieve the "current" line discipline id.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f22f6c935 upstream.
A small window exists where a tty reopen will observe the tty
just prior to imminent teardown (tty->count == 0); in this case, open()
returns EIO to userspace.
Instead, retry the open after checking for signals and yielding;
this interruptible retry loop allows teardown to commence and initialize
a new tty on retry. Never retry the BSD master pty reopen; there is no
guarantee the pty pair teardown is imminent since the slave file
descriptors may remain open indefinitely.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bfd464d3f upstream.
Allow a signal to interrupt the wait for a tty reopen; eg., if
the tty has starting final close and is waiting for the device to
drain.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d27a63caa upstream.
Although n_tty_check_unthrottle() has a valid ldisc reference (since
the tty core gets the ldisc ref in tty_read() before calling the line
discipline read() method), it does not have a valid ldisc reference to
the "other" pty of a pty pair. Since getting an ldisc reference for
tty->link essentially open-codes tty_wakeup(), just replace with the
equivalent tty_wakeup().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gabriel Krisman Bertazi