commit dfcab6ba57 upstream.
dw8250_set_termios() doesn't set baud rate if the arg "old ktermios" is
NULL. This happens during resume.
Call Trace:
...
[ 54.928108] dw8250_set_termios+0x162/0x170
[ 54.928114] serial8250_set_termios+0x17/0x20
[ 54.928117] uart_change_speed+0x64/0x160
[ 54.928119] uart_resume_port
...
So the baud rate is not restored after S3 and breaks the apps who use
UART, for example, console and bluetooth etc.
We address this issue by setting the baud rate irrespective of arg
"old", just like the drivers for other 8250 IPs. This is tested with
Intel Broxton platform.
Signed-off-by: Chen Hu <hu1.chen@intel.com>
Fixes: 4e26b134bd ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 447808bf50 ]
time_init() will set up tb_ticks_per_usec based on reality.
time_init() is called *after* udbg_init_opal_common() during boot.
from arch/powerpc/kernel/time.c:
unsigned long tb_ticks_per_usec = 100; /* sane default */
Currently, all powernv systems have a timebase frequency of 512mhz
(512000000/1000000 == 0x200) - although there's nothing written
down anywhere that I can find saying that we couldn't make that
different based on the requirements in the ISA.
So, we've been (accidentally) thwacking the (currently) correct
(for powernv at least) value for tb_ticks_per_usec earlier than
we otherwise would have.
The "sane default" seems to be adequate for our purposes between
udbg_init_opal_common() and time_init() being called, and if it isn't,
then we should probably be setting it somewhere that isn't hvc_opal.c!
Signed-off-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebec3f8f52 upstream.
syzbot is reporting stalls at __process_echoes() [1]. This is because
since ldata->echo_commit < ldata->echo_tail becomes true for some reason,
the discard loop is serving as almost infinite loop. This patch tries to
avoid falling into ldata->echo_commit < ldata->echo_tail situation by
making access to echo_* variables more carefully.
Since reset_buffer_flags() is called without output_lock held, it should
not touch echo_* variables. And omit a call to reset_buffer_flags() from
n_tty_open() by using vzalloc().
Since add_echo_byte() is called without output_lock held, it needs memory
barrier between storing into echo_buf[] and incrementing echo_head counter.
echo_buf() needs corresponding memory barrier before reading echo_buf[].
Lack of handling the possibility of not-yet-stored multi-byte operation
might be the reason of falling into ldata->echo_commit < ldata->echo_tail
situation, for if I do WARN_ON(ldata->echo_commit == tail + 1) prior to
echo_buf(ldata, tail + 1), the WARN_ON() fires.
Also, explicitly masking with buffer for the former "while" loop, and
use ldata->echo_commit > tail for the latter "while" loop.
[1] https://syzkaller.appspot.com/bug?id=17f23b094cd80df750e5b0f8982c521ee6bcbf40
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+108696293d7a21ab688f@syzkaller.appspotmail.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8afb1d2c12 upstream.
Commit 40f70c03e3 ("serial: sh-sci: add locking to console write
function to avoid SMP lockup") copied the strategy to avoid locking
problems in conjuncture with the console from the UART8250
driver. Instead using directly spin_{try}lock_irqsave(),
local_irq_save() followed by spin_{try}lock() was used. While this is
correct on mainline, for -rt it is a problem. spin_{try}lock() will
check if it is running in a valid context. Since the local_irq_save()
has already been executed, the context has changed and
spin_{try}lock() will complain. The reason why spin_{try}lock()
complains is that on -rt the spin locks are turned into mutexes and
therefore can sleep. Sleeping with interrupts disabled is not valid.
BUG: sleeping function called from invalid context at /home/wagi/work/rt/v4.4-cip-rt/kernel/locking/rtmutex.c:995
in_atomic(): 0, irqs_disabled(): 128, pid: 778, name: irq/76-eth0
CPU: 0 PID: 778 Comm: irq/76-eth0 Not tainted 4.4.126-test-cip22-rt14-00403-gcd03665c8318 #12
Hardware name: Generic RZ/G1 (Flattened Device Tree)
Backtrace:
[<c00140a0>] (dump_backtrace) from [<c001424c>] (show_stack+0x18/0x1c)
r7:c06b01f0 r6:60010193 r5:00000000 r4:c06b01f0
[<c0014234>] (show_stack) from [<c01d3c94>] (dump_stack+0x78/0x94)
[<c01d3c1c>] (dump_stack) from [<c004c134>] (___might_sleep+0x134/0x194)
r7:60010113 r6:c06d3559 r5:00000000 r4:ffffe000
[<c004c000>] (___might_sleep) from [<c04ded60>] (rt_spin_lock+0x20/0x74)
r5:c06f4d60 r4:c06f4d60
[<c04ded40>] (rt_spin_lock) from [<c02577e4>] (serial_console_write+0x100/0x118)
r5:c06f4d60 r4:c06f4d60
[<c02576e4>] (serial_console_write) from [<c0061060>] (call_console_drivers.constprop.15+0x10c/0x124)
r10:c06d2894 r9:c04e18b0 r8:00000028 r7:00000000 r6:c06d3559 r5:c06d2798
r4:c06b9914 r3:c02576e4
[<c0060f54>] (call_console_drivers.constprop.15) from [<c0062984>] (console_unlock+0x32c/0x430)
r10:c06d30d8 r9:00000028 r8:c06dd518 r7:00000005 r6:00000000 r5:c06d2798
r4:c06d2798 r3:00000028
[<c0062658>] (console_unlock) from [<c0062e1c>] (vprintk_emit+0x394/0x4f0)
r10:c06d2798 r9:c06d30ee r8:00000006 r7:00000005 r6:c06a78fc r5:00000027
r4:00000003
[<c0062a88>] (vprintk_emit) from [<c0062fa0>] (vprintk+0x28/0x30)
r10:c060bd46 r9:00001000 r8:c06b9a90 r7:c06b9a90 r6:c06b994c r5:c06b9a3c
r4:c0062fa8
[<c0062f78>] (vprintk) from [<c0062fb8>] (vprintk_default+0x10/0x14)
[<c0062fa8>] (vprintk_default) from [<c009cd30>] (printk+0x78/0x84)
[<c009ccbc>] (printk) from [<c025afdc>] (credit_entropy_bits+0x17c/0x2cc)
r3:00000001 r2:decade60 r1:c061a5ee r0:c061a523
r4:00000006
[<c025ae60>] (credit_entropy_bits) from [<c025bf74>] (add_interrupt_randomness+0x160/0x178)
r10:466e7196 r9:1f536000 r8:fffeef74 r7:00000000 r6:c06b9a60 r5:c06b9a3c
r4:dfbcf680
[<c025be14>] (add_interrupt_randomness) from [<c006536c>] (irq_thread+0x1e8/0x248)
r10:c006537c r9:c06cdf21 r8:c0064fcc r7:df791c24 r6:df791c00 r5:ffffe000
r4:df525180
[<c0065184>] (irq_thread) from [<c003fba4>] (kthread+0x108/0x11c)
r10:00000000 r9:00000000 r8:c0065184 r7:df791c00 r6:00000000 r5:df791d00
r4:decac000
[<c003fa9c>] (kthread) from [<c00101b8>] (ret_from_fork+0x14/0x3c)
r8:00000000 r7:00000000 r6:00000000 r5:c003fa9c r4:df791d00
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Daniel Wagner <daniel.wagner@siemens.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[dw: Backported to 4.4.]
Signed-off-by: Daniel Wagner <daniel.wagner@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa2f80e752 upstream.
The best granularity of residue that DMA engine can report is in the BURST
units, so the serial driver must use MAXBURST = 1 and DMA_SLAVE_BUSWIDTH_1_BYTE
if it relies on exact number of bytes transferred by DMA engine.
Fixes: 62c37eedb7 ("serial: samsung: add dma reqest/release functions")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9f5786987 ]
The arc_uart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_ARC_NR_PORTS), so this can even be triggered using a
legitimate DTB.
Fixes: ea28fd56fc ("serial/arc-uart: switch to devicetree based probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ffab87fdec ]
The lpuart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: c9e2e946fb ("tty: serial: add Freescale lpuart driver support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5673444821 ]
The imx_ports[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: ff05967a07 ("serial/imx: add of_alias_get_id() reference back")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd345a31bf ]
The auart_port[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: 1ea6607d4c ("serial: mxs-auart: Allow device tree probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 49ee23b718 ]
The s3c24xx_serial_ports[] array is indexed using a value derived from
the "serialN" alias in DT, or from an incrementing probe index, which
may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SAMSUNG_UARTS), so this can even be triggered using
a legitimate DTB or legitimate board code.
Fixes: 13a9f6c64f ("serial: samsung: Consider DT alias when probing ports")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e7d75e18d0 ]
The cdns_uart_port[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 928e926349 ("tty: xuartps: Initialize ports according to aliases")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f71a2e0a2 upstream.
To be able to make use of the mctrl-gpio helper from a module these
functions must be exported. This was forgotten in the commit introducing
support interrupt handling for these functions (while it was done for
mctrl_gpio_enable_ms, *sigh*).
Fixes: ce59e48fdb ("serial: mctrl_gpio: implement interrupt handling")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Daniel Wagner <wagi@monom.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9ec225479 upstream.
Commit ea3d8465ab ("tty: n_gsm: Allow ADM response in addition to UA for
control dlci") added support for DLCI to stay in Asynchronous Disconnected
Mode (ADM). But we still get long delays waiting for commands to other
DLCI to complete:
--> 5) C: SABM(P)
Q> 0) C: UIH(F)
Q> 0) C: UIH(F)
Q> 0) C: UIH(F)
...
This happens because gsm_control_send() sets cretries timer to T2 that is
by default set to 34. This will cause resend for T2 times for the control
frame. In ADM mode, we will never get a response so the control frame, so
retries are just delaying all the commands.
Let's fix the issue by setting DLCI_MODE_ADM flag after detecting the ADM
mode for the control DLCI. Then we can use that in gsm_control_send() to
set retries to 1. This means the control frame will be sent once allowing
the other end at an opportunity to switch from ADM to ABM mode.
Note that retries will be decremented in gsm_control_retransmit() so
we don't want to set it to 0 here.
Fixes: ea3d8465ab ("tty: n_gsm: Allow ADM response in addition to UA for control dlci")
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28b0f8a696 upstream.
A tty is hung up by __tty_hangup() setting file->f_op to
hung_up_tty_fops, which is skipped on ttys whose write operation isn't
tty_write(). This means that, for example, /dev/console whose write
op is redirected_tty_write() is never actually marked hung up.
Because n_tty_read() uses the hung up status to decide whether to
abort the waiting readers, the lack of hung-up marking can lead to the
following scenario.
1. A session contains two processes. The leader and its child. The
child ignores SIGHUP.
2. The leader exits and starts disassociating from the controlling
terminal (/dev/console).
3. __tty_hangup() skips setting f_op to hung_up_tty_fops.
4. SIGHUP is delivered and ignored.
5. tty_ldisc_hangup() is invoked. It wakes up the waits which should
clear the read lockers of tty->ldisc_sem.
6. The reader wakes up but because tty_hung_up_p() is false, it
doesn't abort and goes back to sleep while read-holding
tty->ldisc_sem.
7. The leader progresses to tty_ldisc_lock() in tty_ldisc_hangup()
and is now stuck in D sleep indefinitely waiting for
tty->ldisc_sem.
The following is Alan's explanation on why some ttys aren't hung up.
http://lkml.kernel.org/r/20171101170908.6ad08580@alans-desktop
1. It broke the serial consoles because they would hang up and close
down the hardware. With tty_port that *should* be fixable properly
for any cases remaining.
2. The console layer was (and still is) completely broken and doens't
refcount properly. So if you turn on console hangups it breaks (as
indeed does freeing consoles and half a dozen other things).
As neither can be fixed quickly, this patch works around the problem
by introducing a new flag, TTY_HUPPING, which is used solely to tell
n_tty_read() that hang-up is in progress for the console and the
readers should be aborted regardless of the hung-up status of the
device.
The following is a sample hung task warning caused by this issue.
INFO: task agetty:2662 blocked for more than 120 seconds.
Not tainted 4.11.3-dbg-tty-lockup-02478-gfd6c7ee-dirty #28
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
0 2662 1 0x00000086
Call Trace:
__schedule+0x267/0x890
schedule+0x36/0x80
schedule_timeout+0x23c/0x2e0
ldsem_down_write+0xce/0x1f6
tty_ldisc_lock+0x16/0x30
tty_ldisc_hangup+0xb3/0x1b0
__tty_hangup+0x300/0x410
disassociate_ctty+0x6c/0x290
do_exit+0x7ef/0xb00
do_group_exit+0x3f/0xa0
get_signal+0x1b3/0x5d0
do_signal+0x28/0x660
exit_to_usermode_loop+0x46/0x86
do_syscall_64+0x9c/0xb0
entry_SYSCALL64_slow_path+0x25/0x25
The following is the repro. Run "$PROG /dev/console". The parent
process hangs in D state.
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/wait.h>
#include <sys/ioctl.h>
#include <fcntl.h>
#include <unistd.h>
#include <stdio.h>
#include <stdlib.h>
#include <errno.h>
#include <signal.h>
#include <time.h>
#include <termios.h>
int main(int argc, char **argv)
{
struct sigaction sact = { .sa_handler = SIG_IGN };
struct timespec ts1s = { .tv_sec = 1 };
pid_t pid;
int fd;
if (argc < 2) {
fprintf(stderr, "test-hung-tty /dev/$TTY\n");
return 1;
}
/* fork a child to ensure that it isn't already the session leader */
pid = fork();
if (pid < 0) {
perror("fork");
return 1;
}
if (pid > 0) {
/* top parent, wait for everyone */
while (waitpid(-1, NULL, 0) >= 0)
;
if (errno != ECHILD)
perror("waitpid");
return 0;
}
/* new session, start a new session and set the controlling tty */
if (setsid() < 0) {
perror("setsid");
return 1;
}
fd = open(argv[1], O_RDWR);
if (fd < 0) {
perror("open");
return 1;
}
if (ioctl(fd, TIOCSCTTY, 1) < 0) {
perror("ioctl");
return 1;
}
/* fork a child, sleep a bit and exit */
pid = fork();
if (pid < 0) {
perror("fork");
return 1;
}
if (pid > 0) {
nanosleep(&ts1s, NULL);
printf("Session leader exiting\n");
exit(0);
}
/*
* The child ignores SIGHUP and keeps reading from the controlling
* tty. Because SIGHUP is ignored, the child doesn't get killed on
* parent exit and the bug in n_tty makes the read(2) block the
* parent's control terminal hangup attempt. The parent ends up in
* D sleep until the child is explicitly killed.
*/
sigaction(SIGHUP, &sact, NULL);
printf("Child reading tty\n");
while (1) {
char buf[1024];
if (read(fd, buf, sizeof(buf)) < 0) {
perror("read");
return 1;
}
}
return 0;
}
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea3d8465ab ]
Some devices have the control dlci stay in ADM mode instead of the UA
mode. This can seen at least on droid 4 when trying to open the ts
27.010 mux port. Enabling n_gsm debug mode shows the control dlci
always respond with DM to SABM instead of UA:
# modprobe n_gsm debug=0xff
# ldattach -d GSM0710 /dev/ttyS0 &
gsmld_output: 00000000: f9 03 3f 01 1c f9
--> 0) C: SABM(P)
gsmld_receive: 00000000: f9 03 1f 01 36 f9
<-- 0) C: DM(P)
...
$ minicom -D /dev/gsmtty1
minicom: cannot open /dev/gsmtty1: No error information
$ strace minicom -D /dev/gsmtty1
...
open("/dev/gsmtty1", O_RDWR|O_NOCTTY|O_NONBLOCK|O_LARGEFILE) = -1 EL2HLT
Note that this is different issue from other n_gsm -EL2HLT issues such
as timeouts when the control dlci does not respond at all.
The ADM mode seems to be a quite common according to "RF Wireless World"
article "GSM Issue-UE sends SABM and gets a DM response instead of
UA response":
This issue is most commonly observed in GSM networks where in UE sends
SABM and expects network to send UA response but it ends up receiving
DM response from the network. SABM stands for Set asynchronous balanced
mode, UA stands for Unnumbered Acknowledge and DA stands for
Disconnected Mode.
An RLP entity can be in one of two modes:
- Asynchronous Balanced Mode (ABM)
- Asynchronous Disconnected Mode (ADM)
Currently Linux kernel closes the control dlci after several retries
in gsm_dlci_t1() on DM. This causes n_gsm /dev/gsmtty ports to produce
error code -EL2HLT when trying to open them as the closing of control
dlci has already set gsm->dead.
Let's fix the issue by allowing control dlci stay in ADM mode after the
retries so the /dev/gsmtty ports can be opened and used. It seems that
it might take several attempts to get any response from the control
dlci, so it's best to allow ADM mode only after the SABM retries are
done.
Note that for droid 4 additional patches are needed to mux the ttyS0
pins and to toggle RTS gpio_149 to wake up the mdm6600 modem are also
needed to use n_gsm. And the mdm6600 modem needs to be powered on.
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1cf4a7efdc ]
If DMA is enabled and used, a burst of old data may be seen on the
serial console during "poweroff" or "reboot". uart_flush_buffer()
clears the circular buffer, but sci_port.tx_dma_len is not reset.
This leads to a circular buffer overflow, dumping (UART_XMIT_SIZE -
sci_port.tx_dma_len) bytes.
To fix this, add a .flush_buffer() callback that resets
sci_port.tx_dma_len.
Inspired by commit 31ca2c63fd ("tty/serial: atmel: fix race
condition (TX+DMA)").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84b40e3b57 ]
Kernel always writes log messages to console via
serial8250_console_write()->serial8250_console_putchar() which directly
accesses UART_TX register _without_ using DMA.
But, if other processes like systemd using same UART port, then these
writes are handled by a different code flow using 8250_omap driver where
there is provision to use DMA.
It seems that it is possible that both DMA and CPU might simultaneously
put data to UART FIFO and lead to potential loss of data due to FIFO
overflow and weird data corruption. This happens when both kernel
console and userspace tries to write simultaneously to the same UART
port. Therefore, disable DMA on kernel console port to avoid potential
race between CPU and DMA.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65d9982d7e upstream.
ECMA-48 [1] (aka ISO 6429) has defined SGR 21 as "doubly underlined"
since at least March 1984. The Linux kernel has treated it as SGR 22
"normal intensity" since it was added in Linux-0.96b in June 1992.
Before that, it was simply ignored. Other terminal emulators have
either ignored it, or treat it as double underline now. xterm for
example added support in its 304 release (May 2014) [2] where it was
previously ignoring it.
Changing this behavior shouldn't be an issue:
- It isn't a named capability in ncurses's terminfo database, so no
script is using libtinfo/libcurses to look this up, or using tput
to query & output the right sequence.
- Any script assuming SGR 21 will reset intensity in all terminals
already do not work correctly on non-Linux VTs (including running
under screen/tmux/etc...).
- If someone has written a script that only runs in the Linux VT, and
they're using SGR 21 (instead of SGR 22), the output should still
be readable.
imo it's important to change this as the Linux VT's non-conformance
is sometimes used as an argument for other terminal emulators to not
implement SGR 21 at all, or do so incorrectly.
[1]: https://www.ecma-international.org/publications/standards/Ecma-048.htm
[2]: https://github.com/ThomasDickey/xterm-snapshots/commit/2fd29cb98d214cb536bcafbee00bc73b3f1eeb9d
Signed-off-by: Mike Frysinger <vapier@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b022ab754 ]
In case that CONFIG_SLUB_DEBUG is on and pty is used, races between
release_one_tty and flush_to_ldisc work threads may happen and lead
to use-after-free condition on tty->link->port. Because SLUB_DEBUG
is turned on, freed tty->link->port is filled with POISON_FREE value.
So far without SLUB_DEBUG, port was filled with zero and flush_to_ldisc
could return without a problem by checking if tty is NULL.
CPU 0 CPU 1
----- -----
release_tty pty_write
cancel_work_sync(tty) to = tty->link
tty_kref_put(tty->link) tty_schedule_flip(to->port)
<< workqueue >> ...
release_one_tty ...
pty_cleanup ...
kfree(tty->link->port) << workqueue >>
flush_to_ldisc
tty = READ_ONCE(port->itty)
tty is 0x6b6b6b6b6b6b6b6b
!!PANIC!! access tty->ldisc
Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b6b93
pgd = ffffffc0eb1c3000
[6b6b6b6b6b6b6b93] *pgd=0000000000000000, *pud=0000000000000000
------------[ cut here ]------------
Kernel BUG at ffffff800851154c [verbose debug info unavailable]
Internal error: Oops - BUG: 96000004 [#1] PREEMPT SMP
CPU: 3 PID: 265 Comm: kworker/u8:9 Tainted: G W 3.18.31-g0a58eeb #1
Hardware name: Qualcomm Technologies, Inc. MSM 8996pro v1.1 + PMI8996 Carbide (DT)
Workqueue: events_unbound flush_to_ldisc
task: ffffffc0ed610ec0 ti: ffffffc0ed624000 task.ti: ffffffc0ed624000
PC is at ldsem_down_read_trylock+0x0/0x4c
LR is at tty_ldisc_ref+0x24/0x4c
pc : [<ffffff800851154c>] lr : [<ffffff800850f6c0>] pstate: 80400145
sp : ffffffc0ed627cd0
x29: ffffffc0ed627cd0 x28: 0000000000000000
x27: ffffff8009e05000 x26: ffffffc0d382cfa0
x25: 0000000000000000 x24: ffffff800a012f08
x23: 0000000000000000 x22: ffffffc0703fbc88
x21: 6b6b6b6b6b6b6b6b x20: 6b6b6b6b6b6b6b93
x19: 0000000000000000 x18: 0000000000000001
x17: 00e80000f80d6f53 x16: 0000000000000001
x15: 0000007f7d826fff x14: 00000000000000a0
x13: 0000000000000000 x12: 0000000000000109
x11: 0000000000000000 x10: 0000000000000000
x9 : ffffffc0ed624000 x8 : ffffffc0ed611580
x7 : 0000000000000000 x6 : ffffff800a42e000
x5 : 00000000000003fc x4 : 0000000003bd1201
x3 : 0000000000000001 x2 : 0000000000000001
x1 : ffffff800851004c x0 : 6b6b6b6b6b6b6b93
Signed-off-by: Sahara <keun-o.park@darkmatter.ae>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7842055bfc upstream.
When the TTY buffers fill up to the configured maximum, a system lockup
occurs:
[ 598.820128] INFO: rcu_preempt detected stalls on CPUs/tasks:
[ 598.825796] 0-...!: (1 GPs behind) idle=5a6/2/0 softirq=1974/1974 fqs=1
[ 598.832577] (detected by 3, t=62517 jiffies, g=296, c=295, q=126)
[ 598.838755] Task dump for CPU 0:
[ 598.841977] swapper/0 R running task 0 0 0 0x00000022
[ 598.849023] Call trace:
[ 598.851476] __switch_to+0x98/0xb0
[ 598.854870] (null)
This can be prevented by doing a dummy read of the RX data register.
This issue affects both HSCIF and SCIF ports. Reported for R-Car H3 ES2.0;
reproduced and fixed on H3 ES1.1. Probably affects other R-Car platforms
as well.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05ead49691 upstream.
When CONFIG_PCI is not set, enabling CONFIG_CYZ_INTR has no
practical effect other than generating a warning about an
unused function:
drivers/tty/cyclades.c:1184:20: warning: 'cyz_interrupt' defined but not used [-Wunused-function]
static irqreturn_t cyz_interrupt(int irq, void *dev_id)
This adds a dependency to avoid that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e36ae34399 upstream.
xencons_disconnect_backend() is only called from xen_console_remove(),
which is conditionally compiled, so we get a harmless warning when
CONFIG_HVC_XEN_FRONTEND is unset:
hvc/hvc_xen.c:350:12: error: 'xen_console_remove' defined but not used [-Werror=unused-function]
This moves the function down into the same #ifdef section to silence
the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38b1f0fb42 upstream.
The wakeup mechanism via RTSDEN bit relies on the system using the RTS/CTS
lines, so only allow such wakeup method when the system actually has
RTS/CTS support.
Fixes: bc85734b12 ("serial: imx: allow waking up on RTSD")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 984cf355ae upstream.
Commit 984d74a720 ("sysrq: rcu-ify __handle_sysrq") replaced
spin_lock_irqsave() calls with rcu_read_lock() calls in sysrq. Since
rcu_read_lock() does not disable preemption, faulthandler_disabled() in
__do_page_fault() in x86/fault.c returns false. When the code later calls
might_sleep() in the pagefault handler, we get the following warning:
BUG: sleeping function called from invalid context at ../arch/x86/mm/fault.c:1187
in_atomic(): 0, irqs_disabled(): 0, pid: 4706, name: bash
Preemption disabled at:[<ffffffff81484339>] printk+0x48/0x4a
To fix this, we release the RCU read lock before we crash.
Tested this patch on linux 3.18 by booting off one of our boards.
Fixes: 984d74a720 ("sysrq: rcu-ify __handle_sysrq")
Signed-off-by: Ani Sinha <ani@arista.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 966031f340 upstream.
We added support for EXTPROC back in 2010 in commit 26df6d1340 ("tty:
Add EXTPROC support for LINEMODE") and the intent was to allow it to
override some (all?) ICANON behavior. Quoting from that original commit
message:
There is a new bit in the termios local flag word, EXTPROC.
When this bit is set, several aspects of the terminal driver
are disabled. Input line editing, character echo, and mapping
of signals are all disabled. This allows the telnetd to turn
off these functions when in linemode, but still keep track of
what state the user wants the terminal to be in.
but the problem turns out that "several aspects of the terminal driver
are disabled" is a bit ambiguous, and you can really confuse the n_tty
layer by setting EXTPROC and then causing some of the ICANON invariants
to no longer be maintained.
This fixes at least one such case (TIOCINQ) becoming unhappy because of
the confusion over whether ICANON really means ICANON when EXTPROC is set.
This basically makes TIOCINQ match the case of read: if EXTPROC is set,
we ignore ICANON. Also, make sure to reset the ICANON state ie EXTPROC
changes, not just if ICANON changes.
Fixes: 26df6d1340 ("tty: Add EXTPROC support for LINEMODE")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Reported-by: syzkaller <syzkaller@googlegroups.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b00bebbc30 ]
When kernel configuration SMP,PREEMPT and DEBUG_PREEMPT are enabled,
echo 1 >/proc/sys/kernel/sysrq
echo p >/proc/sysrq-trigger
kernel will print call trace as below:
sysrq: SysRq : Show Regs
BUG: using __this_cpu_read() in preemptible [00000000] code: sh/435
caller is __this_cpu_preempt_check+0x18/0x20
Call trace:
[<ffffff8008088e80>] dump_backtrace+0x0/0x1d0
[<ffffff8008089074>] show_stack+0x24/0x30
[<ffffff8008447970>] dump_stack+0x90/0xb0
[<ffffff8008463950>] check_preemption_disabled+0x100/0x108
[<ffffff8008463998>] __this_cpu_preempt_check+0x18/0x20
[<ffffff80084c9194>] sysrq_handle_showregs+0x1c/0x40
[<ffffff80084c9c7c>] __handle_sysrq+0x12c/0x1a0
[<ffffff80084ca140>] write_sysrq_trigger+0x60/0x70
[<ffffff8008251e00>] proc_reg_write+0x90/0xd0
[<ffffff80081f1788>] __vfs_write+0x48/0x90
[<ffffff80081f241c>] vfs_write+0xa4/0x190
[<ffffff80081f3354>] SyS_write+0x54/0xb0
[<ffffff80080833f0>] el0_svc_naked+0x24/0x28
This can be seen on a common board like an r-pi3.
This happens because when echo p >/proc/sysrq-trigger,
get_irq_regs() is called outside of IRQ context,
if preemption is enabled in this situation,kernel will
print the call trace. Since many prior discussions on
the mailing lists have made it clear that get_irq_regs
either just returns NULL or stale data when used outside
of IRQ context,we simply avoid calling it outside of
IRQ context.
Signed-off-by: Jibin Xu <jibin.xu@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ab84da2e0 ]
The upper four bits of the XR17V35x fractional divisor register (DLD)
control general chip function (RS-485 direction pin polarity, multidrop
mode, XON/XOFF parity check, and fast IR mode). Don't allow these bits
to be clobbered when setting the baudrate.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3236a96548 ]
This driver's ->rs485_config callback checks if SER_RS485_RTS_ON_SEND
and SER_RS485_RTS_AFTER_SEND have the same value. If they do, it means
the user has passed in invalid data with the TIOCSRS485 ioctl()
since RTS must have a different polarity when sending and when not
sending. In this case, rs485 mode is not enabled (the RS485_URA bit
is not set in the RS485 Enable Register) and this is supposed to be
signaled back to the user by clearing the SER_RS485_ENABLED bit in
struct serial_rs485 ... except a missing tilde character is preventing
that from happening.
Fixes: 28e3fb6c4d ("serial: Add support for Fintek F81216A LPC to 4 UART")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a71de2f73 upstream.
Commit 348f9bb31c ("serial: omap: Fix RTS handling") sought to enable
auto RTS upon manual RTS assertion and disable it on deassertion.
However it seems the latter was done incorrectly, it clears all bits in
the Extended Features Register *except* auto RTS.
Fixes: 348f9bb31c ("serial: omap: Fix RTS handling")
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a5a90a2a4 upstream.
Sergey noticed a small but fatal mistake in __tty_insert_flip_char,
leading to an oops in an interrupt handler when using any serial
port.
The problem is that I accidentally took the tty_buffer pointer
before calling __tty_buffer_request_room(), which replaces the
buffer. This moves the pointer lookup to the right place after
allocating the new buffer space.
Fixes: 979990c628 ("tty: improve tty_insert_flip_char() fast path")
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 065ea0a7af upstream.
While working on improving the fast path of tty_insert_flip_char(),
I noticed that by calling tty_buffer_request_room(), we needlessly
move to the separate flag buffer mode for the tty, even when all
characters use TTY_NORMAL as the flag.
This changes the code to call __tty_buffer_request_room() with the
correct flag, which will then allocate a regular buffer when it rounds
out of space but no special flags have been used. I'm guessing that
this is the behavior that Peter Hurley intended when he introduced
the compacted flip buffers.
Fixes: acc0f67f30 ("tty: Halve flip buffer GFP_ATOMIC memory consumption")
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 979990c628 upstream.
kernelci.org reports a crazy stack usage for the VT code when CONFIG_KASAN
is enabled:
drivers/tty/vt/keyboard.c: In function 'kbd_keycode':
drivers/tty/vt/keyboard.c:1452:1: error: the frame size of 2240 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
The problem is that tty_insert_flip_char() gets inlined many times into
kbd_keycode(), and also into other functions, and each copy requires 128
bytes for stack redzone to check for a possible out-of-bounds access on
the 'ch' and 'flags' arguments that are passed into
tty_insert_flip_string_flags as a variable-length string.
This introduces a new __tty_insert_flip_char() function for the slow
path, which receives the two arguments by value. This completely avoids
the problem and the stack usage goes back down to around 100 bytes.
Without KASAN, this is also slightly better, as we don't have to
spill the arguments to the stack but can simply pass 'ch' and 'flag'
in registers, saving a few bytes in .text for each call site.
This should be backported to linux-4.0 or later, which first introduced
the stack sanitizer in the kernel.
Fixes: c420f167db ("kasan: enable stack instrumentation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6987dc8a70 upstream.
Only read access is checked before this call.
Actually, at the moment this is not an issue, as every in-tree arch does
the same manual checks for VERIFY_READ vs VERIFY_WRITE, relying on the MMU
to tell them apart, but this wasn't the case in the past and may happen
again on some odd arch in the future.
If anyone cares about 3.7 and earlier, this is a security hole (untested)
on real 80386 CPUs.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be40597a1b upstream.
UARTn_FRAME_PARITY_ODD is 0x0300
UARTn_FRAME_PARITY_EVEN is 0x0200
So if the UART is configured for EVEN parity, it would be reported as ODD.
Fix it by correctly testing if the 2 bits are set.
Fixes: 3afbd89c96 ("serial/efm32: add new driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen Hu