Reverted upstream by commit 6a22c57b8d
Revert this commit:
commit 2e1c49db4c
Author: Zou Nan hai <nanhai.zou@intel.com>
Date: Fri Jun 1 00:46:28 2007 -0700
x86_64: allocate sparsemem memmap above 4G
This reverts commit 2e1c49db4c.
First off, testing in Fedora has shown it to cause boot failures,
bisected down by Martin Ebourne, and reported by Dave Jobes. So the
commit will likely be reverted in the 2.6.23 stable kernels.
Secondly, in the 2.6.24 model, x86-64 has now grown support for
SPARSEMEM_VMEMMAP, which disables the relevant code anyway, so while the
bug is not visible any more, it's become invisible due to the code just
being irrelevant and no longer enabled on the only architecture that
this ever affected.
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Martin Ebourne <fedora@ebourne.me.uk>
Cc: Zou Nan hai <nanhai.zou@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch edaf420fdc in mainline.
I ran into this problem on a system that was unable to obtain NTP sync
because the clock was running very slow (over 10000ppm slow). ntpd had
declared all of its peers 'reject' with 'peer_dist' reason.
On investigation, the tsc_khz variable was significantly incorrect
causing xtime to run slow. After a reboot tsc_khz was correct so I
did a reboot test to see how often the problem occurred:
Test was done on a 2000 Mhz Xeon system. Of 689 reboots, 8 of them
had unacceptable tsc_khz values (>500ppm):
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 21 3.048%
1999800 - 1999850 166 24.128%
1999850 - 1999900 241 35.029%
1999900 - 1999950 211 30.669%
1999950 - 2000000 42 6.105%
2000000 - 2000000 0 0.000%
2000050 - 2000100 0 0.000%
[...]
2000100 - 2015000 1 0.145% << BAD
2015000 - 2030000 6 0.872% << BAD
2030000 - 2045000 1 0.145% << BAD
2045000 < 0 0.000%
The worst boot was 2032.577 Mhz, over 1.5% off!
It appears that on rare occasions, mach_countup() is taking longer to
complete than necessary.
I suspect that this is caused by the CPU taking a periodic SMI
interrupt right at the end of the 30ms calibration loop. This would
cause the loop to delay while the SMI BIOS hander runs. The resulting
TSC value is beyond what it actually should be resulting in a higher
tsc_khz.
The below patch makes native_calculate_cpu_khz() take the best
(shortest duration, lowest khz) run of it's 3 calibration loops. If a
SMI goes off causing a bad result (long duration, higher khz) it will
be discarded.
With the patch applied, 300 boots of the same system produce good
results:
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 30 10.000%
1999800 - 1999850 166 55.333%
1999850 - 1999900 89 29.667%
1999900 - 1999950 15 5.000%
1999950 < 0 0.000%
Problem was found and tested against 2.6.18. Patch is against 2.6.22.
Signed-off-by: Dave Johnson <djohnson@sw.starentnetworks.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch e6e1ace990 in mainline.
We use signed values for limit checking since the values can go
negative under certain circumstances. However, sizeof() is unsigned
and forces the comparison to be unsigned, so move the comparison into
the heap_free() macros so we can ensure it is a signed comparison.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 6b6815c6d5 in mainline.
Apparently some specific versions of LILO enter the kernel with a
stack pointer that doesn't match the rest of the segments. Make our
best attempt at untangling the resulting mess.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 9a24d04a3c upstream
While we were reviewing pageattr_32/64.c for unification,
Thomas Gleixner noticed the following serious SMP bug in
global_flush_tlb():
down_read(&init_mm.mmap_sem);
list_replace_init(&deferred_pages, &l);
up_read(&init_mm.mmap_sem);
this is SMP-unsafe because list_replace_init() done on two CPUs in
parallel can corrupt the list.
This bug has been introduced about a year ago in the 64-bit tree:
commit ea7322decb
Author: Andi Kleen <ak@suse.de>
Date: Thu Dec 7 02:14:05 2006 +0100
[PATCH] x86-64: Speed and clean up cache flushing in change_page_attr
down_read(&init_mm.mmap_sem);
- dpage = xchg(&deferred_pages, NULL);
+ list_replace_init(&deferred_pages, &l);
up_read(&init_mm.mmap_sem);
the xchg() based version was SMP-safe, but list_replace_init() is not.
So this "cleanup" introduced a nasty bug.
why this bug never become prominent is a mystery - it can probably be
explained with the (still) relative obscurity of the x86_64 architecture.
the safe fix for now is to write-lock init_mm.mmap_sem.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch e3d2697669 in mainline.
The kernel's copy of struct vcpu_register_vcpu_info was out of date,
at best causing the hypercall to fail and the guest kernel to fall
back to the old mechanism, or worse, causing random memory corruption.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Stable Kernel <stable@kernel.org>
Cc: Morten =?utf-8?q?B=C3=B8geskov?= <xen-users@morten.bogeskov.dk>
Cc: Mark Williamson <mark.williamson@cl.cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 9f79991d41 in mainline.
When a pagetable is no longer in use, it must be unpinned so that its
pages can be freed. However, this is only possible if there are no
stray uses of the pagetable. The code currently deals with all the
usual cases, but there's a rare case where a vcpu is changing cr3, but
is doing so lazily, and the change hasn't actually happened by the time
the pagetable is unpinned, even though it appears to have been completed.
This change adds a second per-cpu cr3 variable - xen_current_cr3 -
which tracks the actual state of the vcpu cr3. It is only updated once
the actual hypercall to set cr3 has been completed. Other processors
wishing to unpin a pagetable can check other vcpu's xen_current_cr3
values to see if any cross-cpu IPIs are needed to clean things up.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch 91e0c5f3da in mainline.
This adds a mechanism to register a callback function to be called once
a batch of hypercalls has been issued. This is typically used to unlock
things which must remain locked until the hypercall has taken place.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a24864a1d5
uml: definitively kill subprocesses on panic
In a stock 2.6.22.6 kernel, poweroff a user mode linux guest (2.6.22.6 running
in skas0 mode) will halt the host linux. I think the reason is the kernel
thread abort because of a bug. Then the sys_reboot in process of user mode
linux guest is not trapped by the user mode linux kernel and is executed by
host. I think it is better to make sure all of our children process to quit
when user mode linux kernel abort.
[ jdike - the kernel process needs to ignore SIGTERM, plus the waitpid/kill
loop is needed to make sure that all of our children are dead before the
kernel exits ]
Signed-off-by: Lepton Wu <ytht.net@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 189872f968 in mainline.
uml: don't use glibc asm/user.h
Stop including asm/user.h from libc - it seems to be disappearing from
distros. It's replaced with sys/user.h which defines user_fpregs_struct and
user_fpxregs_struct instead of user_i387_struct and struct user_fxsr_struct on
i386.
As a bonus, on x86_64, I get to dump some stupid typedefs which were needed in
order to get asm/user.h to compile.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 818f6ef407 in mainline.
uml: fix an IPV6 libc vs kernel symbol clash
On some systems, with IPV6 configured, there is a clash between the kernel's
in6addr_any and the one in libc.
This is handled in the usual (gross) way of defining the kernel symbol out of
the way on the gcc command line.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 71f926f2ea in mainline.
uml: stop using libc asm/page.h
Remove includes of asm/page.h from libc code. This header seems to be
disappearing, and UML doesn't make much use of it anyway.
The one use, PAGE_SHIFT in stub.h, is handled by copying the constant from the
kernel side of the house in common_offsets.h.
[ jdike - added arch/um/kernel/skas/clone.c for -stable ]
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch db220b234d in mainline.
pci_device_to_OF_node() returns the device node attached to a PCI device,
but doesn't actually grab a reference - we need to do it ourselves.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch ba02946a90 in mainline
Its legal for the stfiwx instruction to have RA = 0 as part of its
effective address calculation. This is illegal for all other XE
form instructions.
Add code to compute the proper effective address for stfiwx if
RA = 0 rather than treating it as illegal.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch a76ab5c10d in mainline.
When GDB writes a breakpoint into address area of inferior process the
kernel needs to invalidate the modified memory in the inferior which
is done by calling flush_cache_page which in turns calls
r4k_flush_cache_page and local_r4k_flush_cache_page for VSMP or SMTC
kernel via r4k_on_each_cpu().
As the VSMP and SMTC SMP kernels for 34K are running on a single shared
caches it is possible to get away without interprocessor function calls.
This optimization is implemented in r4k_on_each_cpu, so
local_r4k_flush_cache_page is only ever called on the local CPU.
This is where the following code in local_r4k_flush_cache_page() strikes:
/*
* If ownes no valid ASID yet, cannot possibly have gotten
* this page into the cache.
*/
if (cpu_context(smp_processor_id(), mm) == 0)
return;
On VSMP and SMTC had a function of cpu_context() for each CPU(TC).
So in case another CPU than the CPU executing local_r4k_cache_flush_page
has not accessed the mm but one of the other CPUs has there may be data
to be flushed in the cache yet local_r4k_cache_flush_page will falsely
return leaving the I-cache inconsistent for the breakpoint.
While the issue was discovered with GDB it also exists in
local_r4k_flush_cache_range() and local_r4k_flush_cache().
Fixed by introducing a new function has_valid_asid which on MT kernels
returns true if a mm is active on any processor in the system.
This is relativly expensive since for memory acccesses in that loop
cache misses have to be assumed but it seems the most viable solution
for 2.6.23 and older -stable kernels.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch d58aa8c7b1 in mainline.
From: Chris Wright <chrisw@sous-sol.org>
Date: Tue, 23 Oct 2007 20:36:14 -0700
Subject: [PATCH] [SPARC64]: pass correct addr in get_fb_unmapped_area(MAP_FIXED)
Looks like the MAP_FIXED case is using the wrong address hint. I'd
expect the comment "don't mess with it" means pass the request
straight on through, not change the address requested to -ENOMEM.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch d060db63fd in mainline.
[SPARC64]: Fix register usage in xor_raid_4().
Some typos led to using %i6/%i7 instead of %l6/%l7 in loads which is
really really bad because those are the frame pointer and return PC.
Based upon a raid5 crash report by Bertrand Joel.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a wrong ifdef in the board setup code, leading to the GPIO
pin not being pulled high, and thus the USB switch not being powered at all.
This finishes the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which
started in 2005 (before 2.6.12-rc2), then probably because things were
working anyway for most people got forgotten.
[Ralf: Paolo's original patch didn't fix the module case, Florian's patch
only fixed MTX1 etc. so this is a combined patch plus some cleanups.]
Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
VIA C3 Ezra-T has RevisionID equal to 1, but it needs RevisionKey to be 0
or CPU will ignore new frequency and will continue to work at old
frequency. New "revid_errata" option will force RevisionKey to be set to
0, whatever RevisionID is.
Additionaly "Longhaul" will not silently ignore unsuccessful transition.
It will try to check if "revid_errata" or "disable_acpi_c3" options need to
be enabled for this processor/system.
Same for Longhaul ver. 2 support. It will be disabled if none of above
options will work.
Best case scenario (with patch apllied and v2 enabled):
longhaul: VIA C3 'Ezra' [C5C] CPU detected. Longhaul v2 supported.
longhaul: Using northbridge support.
longhaul: VRM 8.5
longhaul: Max VID=1.350 Min VID=1.050, 13 possible voltage scales
longhaul: f: 300000 kHz, index: 0, vid: 1050 mV
[...]
longhaul: Voltage scaling enabled.
Worst case scenario:
longhaul: VIA C3 'Ezra-T' [C5M] CPU detected. Powersaver supported.
longhaul: Using northbridge support.
longhaul: Using ACPI support.
longhaul: VRM 8.5
longhaul: Claims to support voltage scaling but min & max are both 1.250. Voltage scaling disabled
longhaul: Failed to set requested frequency!
longhaul: Enabling "Ignore Revision ID" option.
longhaul: Failed to set requested frequency!
longhaul: Disabling ACPI C3 support.
longhaul: Disabling "Ignore Revision ID" option.
longhaul: Failed to set requested frequency!
longhaul: Enabling "Ignore Revision ID" option.
[akpm@linux-foundation.org: coding-style cleanups]
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4598/2: OSIRIS: Ensure we do not get nRSTOUT during suspend
[ARM] 4597/2: OSIRIS: ensure CPLD0 is preserved after suspend
Ensure that CPLD is restored to the original state
on resume, and that before going into suspend we
select the NAND bank we booted from for restarting.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix 'niu' complex IRQ probing.
[SPARC64]: check fork_idle() error
[SPARC64]: Temporary workaround for PCI-E slot on T1000.
[SPARC64]: VIO device addition log message level is too high.
[SPARC64]: Fix domain-services port probing.
[SPARC64]: Don't use in/local regs for ldx/stx data in N1 memcpy.
Fixe MACE PCI addressing by adding the bus number parameter.
Remove check of the used slot since every slot should be valid.
Converted mkaddr from #define to inline function.
Signed-off-by: Giuseppe Sacco <eppesuig@debian.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PCI-E slot on T1000 connects directly to the Fire PCI chip with no
intervening bridges visible in the OBP tree.
Unfortunately the bus numbering of the device in that slot is
different (2) from the PCI host controller (0), and thus the
pci_bus_{read,write}_config_*() calls don't work out.
Complicating things further the Fire PCI controller has no config
space it responds to either.
For now treat this case specially so that devices in the slot work.
Longer term we need to perhaps cons up a dummy bridge between the Fire
and the PCI-E slot so that the bus hierarchy is complete inside of the
kernel and thus the bus numbering all works out right.
Signed-off-by: David S. Miller <davem@davemloft.net>
We should only use ports underneath "domain-services", other DS ports
in the MDESC aren't for us to use.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Terminally fix local_{dec,sub}_if_positive
[MIPS] Type proof reimplementation of cmpxchg.
[MIPS] pg-r4k.c: Fix a typo in an R4600 v2 erratum workaround
Restore a load from KSEG1 done as a workaround for an R4600 v2
erratum, dropped with 211be16de99a7424e66c0b6c0d00e2c970508ac2.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It doesn't matter for use in 64-bit objects, but when used in
32-bit environments the top 32-bits of the local and in
registers will get chopped off on the next register window
spill/restore which leads to difficult to track down and
subtle bugs.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix missing load-twin usage in Niagara-1 memcpy.
[SPARC64]: Fix put_user() calls in binfmt_aout32.c
[SPARC]: Fix EBUS use of uninitialized variable.
For the case where the source is not aligned modulo 8
we don't use load-twins to suck the data in and this
kills performance since normal loads allocate in the
L1 cache (unlike load-twin) and thus big memcpys swipe
the entire L1 D-cache.
We need to allocate a register window to implement this
properly, but that actually simplifies a lot of things
as a nice side-effect.
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason old binutils genertate larger headers so increase the text
offset of the vdso to avoid linker errors.
Roland McGrath explains:
"There are extra symbols in the '.dynsym' section that are responsible
for the size difference (They also cause corresponding inflation in
'.gnu.version')
Older ld's wrongly generated these unneeded symbols in .dynsym. This
was fixed not all that long ago (2006); binutils-2.17.50.0.6 might be
the first fixed version, but I have not verified for sure where the
cutoff was.
The unneeded symbols et al from old ld add almost 700 bytes excess.
This limits fairly tightly the amount by which the actual text and
data in the vDSO can grow in the future without pushing the whole
file over 4kb. If it does grow later on, we should consider changing
the layout with a config option or something to pack it better
without that padding, when building the kernel with newer binutils."
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a POWER6 machine running 2.6.23-rc8 I sometimes see the following error:
xics_set_affinity: No online cpus in the mask 00000000,00000000,00000000,00000001 for irq 20
In a desperate attempt to get a changelog entry in 2.6.23, I took a look
into it.
It turns out we are passing a real and not a virtual irq into
get_irq_server. This works for the case where hwirq < NR_IRQS and we
set virq = hwirq. In my case however hwirq = 590082 and we try and
access irq_desc[590082], slightly past the end at 512 entries.
Lucky we ship lots of memory with our machines.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Store any note sections after the exception tables like the other
architectures do. This is required for .note.gnu.build-id emitted from
binutils 2.18 onwards if nothing else.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
argv and envp are pointers to u32's in userspace, so don't
try to put_user() a NULL to them.
Aparently gcc-4.2.x now warns about this, and since we use
-Werror for arch/sparc64 code, this breaks the build.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following (valid) section warnings:
WARNING: vmlinux.o(.text+0xf7b5c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bridge')
WARNING: vmlinux.o(.text+0xfc5f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_map_rom' and 'pci_unmap_rom')
WARNING: vmlinux.o(.text+0xfc824): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_update_resource' and 'pci_claim_resource')
WARNING: vmlinux.o(.text+0xfd6d8): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfd730): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfd788): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfd7e0): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfe024): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'sys_pciconfig_read')
WARNING: vmlinux.o(.text+0xfe0f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'sys_pciconfig_read')
WARNING: vmlinux.o(.text+0xfe17c): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'sys_pciconfig_read')
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix fallocate on o32 binary compat ABI
[MIPS] Fix CONFIG_BUILD_ELF64 kernels with symbols in CKSEG0.
[MIPS] IP32: Fix initialization of UART base addresses.
MIPS was mistakenly forgetting to use the fallocate compat wrapper, which
I noticed while cleaning up all the duplicate fallocate wrappers.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds