Since commit 05e0caad3b7b ("[PATCH] Have ia64 use add_active_range() and
free_area_init_nodes") the num_dma_physpages member of 'struct
early_node_data' is calculated but never used. Remove it.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The FLATMEM version of paging_init has calls to free_area_init_nodes() in
the end of every branch of 'if' and 'ifdef' statements.
Let's call this function outside the 'ifdef' and 'if' statements instead.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Linux expects that if a CPU modifies a memory location, then that
modification will eventually become visible to other CPUs in the system.
Loongson 3 CPUs include a Store Fill Buffer (SFB) which sits between a
core & its L1 data cache, queueing memory accesses & allowing for faster
forwarding of data from pending stores to younger loads from the core.
Unfortunately the SFB prioritizes loads such that a continuous stream of
loads may cause a pending write to be buffered indefinitely. This is
problematic if we end up with 2 CPUs which each perform a store that the
other polls for - one or both CPUs may end up with their stores buffered
in the SFB, never reaching cache due to the continuous reads from the
poll loop. Such a deadlock condition has been observed whilst running
qspinlock code.
This patch changes the definition of cpu_relax() to smp_mb() for
Loongson-3, forcing a flush of the SFB on SMP systems which will cause
any pending writes to make it as far as the L1 caches where they will
become visible to other CPUs. If the kernel is not compiled for SMP
support, this will expand to a barrier() as before.
This workaround matches that currently implemented for ARM when
CONFIG_ARM_ERRATA_754327=y, which was introduced by commit 534be1d5a2da
("ARM: 6194/1: change definition of cpu_relax() for ARM11MPCore").
Although the workaround is only required when the Loongson 3 SFB
functionality is enabled, and we only began explicitly enabling that
functionality in v4.7 with commit 1e820da3c9af ("MIPS: Loongson-3:
Introduce CONFIG_LOONGSON3_ENHANCEMENT"), existing or future firmware
may enable the SFB which means we may need the workaround backported to
earlier kernels too.
[paul.burton@mips.com:
- Reword commit message & comment.
- Limit stable backport to v3.15+ where we support Loongson 3 CPUs.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
References: 534be1d5a2da ("ARM: 6194/1: change definition of cpu_relax() for ARM11MPCore")
References: 1e820da3c9af ("MIPS: Loongson-3: Introduce CONFIG_LOONGSON3_ENHANCEMENT")
Patchwork: https://patchwork.linux-mips.org/patch/19830/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
Cc: stable@vger.kernel.org # v3.15+
This pin is externally pulled up, so we need to disable the SoC's
internal pull down resistor to allow it to function properly.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This pin is externally pulled up, so we need to disable the
SoC's internal pull-down.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This pin is externally pulled up, so we should disable the SoC's
pull down resistor in order for the interrupt to function properly.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This pins are externally pulled up, and so we should explicitly
configure them to disable the SoC-internal pull-downs. Previously
we relied on the bootloader doing this in order to allow the buttons
to function properly.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Currently, we assume that the bootloader has correctly configured
the interrupt pin for max77693. This might not actually be the case -
so it's better to configure it explicitly.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix typos 's/wit/with/' in the comments and sort headers alphabetically
in order to avoid duplicate includes in future.
Fixes: bcf7eac3d97f ("regmap: add SCCB support")
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to invoke release_inactive_stripe_list() with interrupts
disabled. All call sites, except raid5_release_stripe(), unlock
->device_lock and enable interrupts before invoking the function.
Make it consistent.
Cc: Shaohua Li <shli@kernel.org>
Cc: linux-raid@vger.kernel.org
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Shaohua Li <shli@fb.com>
Support for device-only IPv6 multipath next hops was dropped in
commit 33bd5ac54dc4 ("net/ipv6: Revert attempt to simplify route replace
and append") and as of commit b5d2d75e079a ("net/ipv6: Do not allow
device only routes via the multipath API"), attempts to add a next hop
like that yield an explicit diagnostic.
Correspondingly, drop the IPv6 parts of GRE multipath test that are
supposed to test that code.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
net: bridge: add support for backup port
This set introduces a new bridge port option that allows any port to have
any other port (in the same bridge of course) as its backup and traffic
will be forwarded to the backup port when the primary goes down. This is
mainly used in MLAG and EVPN setups where we have peerlink path which is
a backup of many (or even all) ports and is a participating bridge port
itself. There's more detailed information in patch 02. Patch 01 just
prepares the port sysfs code for options that take raw value. The main
issues that this set solves are scalability and fallback latency.
We have used similar code for over 6 months now to bring the fallback
latency of the backup peerlink down and avoid fdb notification storms.
Also due to the nature of master devices such setup is currently not
possible, and last but not least having tens of thousands of fdbs require
thousands of calls to switch.
I've also CCed our MLAG experts that have been using similar option.
Roopa also adds:
"Two switches acting in a MLAG pair are connected by the peerlink
interface which is a bridge port.
the config on one of the switches looks like the below. The other
switch also has a similar config.
eth0 is connected to one port on the server. And the server is
connected to both switches.
br0 -- team0---eth0
|
-- switch-peerlink
switch-peerlink becomes the failover/backport port when say team0 to
the server goes down.
Today, when team0 goes down, control plane has to withdraw all the fdb
entries pointing to team0
and re-install the fdb entries pointing to switch-peerlink...and
restore the fdb entries when team0 comes back up again.
and this is the problem we are trying to solve.
This also becomes necessary when multihoming is implemented by a
standard like E-VPN https://tools.ietf.org/html/rfc8365#section-8
where the 'switch-peerlink' is an overlay vxlan port (like nikolay
mentions in his patch commit). In these implementations, the fdb scale
can be much larger.
On why bond failover cannot be used here ?: the point that nikolay was
alluding to is, switch-peerlink in the above example is a bridge port
and is a failover/backport port for more than one or all ports in the
bridge br0. And you cannot enslave switch-peerlink into a second level
team
with other bridge ports. Hence a multi layered team device is not an
option (FWIW, switch-peerlink is also a teamed interface to the peer
switch)."
v3: Added Roopa's explanation and diagram
v2: In patch 01 use kstrdup/kfree to avoid casting the const buf. In order
to avoid using GFP_ATOMIC or always allocating I kept the spinlock inside
each branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which
allows to set a backup port to be used for known unicast traffic if the
port has gone carrier down. The backup pointer is rcu protected and set
only under RTNL, a counter is maintained so when deleting a port we know
how many other ports reference it as a backup and we remove it from all.
Also the pointer is in the first cache line which is hot at the time of
the check and thus in the common case we only add one more test.
The backup port will be used only for the non-flooding case since
it's a part of the bridge and the flooded packets will be forwarded to it
anyway. To remove the forwarding just send a 0/non-existing backup port.
This is used to avoid numerous scalability problems when using MLAG most
notably if we have thousands of fdbs one would need to change all of them
on port carrier going down which takes too long and causes a storm of fdb
notifications (and again when the port comes back up). In a Multi-chassis
Link Aggregation setup usually hosts are connected to two different
switches which act as a single logical switch. Those switches usually have
a control and backup link between them called peerlink which might be used
for communication in case a host loses connectivity to one of them.
We need a fast way to failover in case a host port goes down and currently
none of the solutions (like bond) cannot fulfill the requirements because
the participating ports are actually the "master" devices and must have the
same peerlink as their backup interface and at the same time all of them
must participate in the bridge device. As Roopa noted it's normal practice
in routing called fast re-route where a precalculated backup path is used
when the main one is down.
Another use case of this is with EVPN, having a single vxlan device which
is backup of every port. Due to the nature of master devices it's not
currently possible to use one device as a backup for many and still have
all of them participate in the bridge (which is master itself).
More detailed information about MLAG is available at the link below.
https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG
Further explanation and a diagram by Roopa:
Two switches acting in a MLAG pair are connected by the peerlink
interface which is a bridge port.
the config on one of the switches looks like the below. The other
switch also has a similar config.
eth0 is connected to one port on the server. And the server is
connected to both switches.
br0 -- team0---eth0
|
-- switch-peerlink
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new alternative store callback for port sysfs options
which takes a raw value (buf) and can use it directly. It is needed for the
backup port sysfs support since we have to pass the device by its name.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the "bad summary count" mount flag from the previous patch to skip
writing the unmount record to force log recovery at the next mount,
which will recalculate the summary counters for us.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Refactor the writing of the unmount record into a separate helper. No
functionality changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Filippo Giunchedi complained that xfs doesn't even perform basic sanity
checks of the fs summary counters at mount time. Therefore, recalculate
the summary counters from the AGFs after log recovery if the counts were
bad (or we had to recover the fs). Enhance the recalculation routine to
fail the mount entirely if the new values are also obviously incorrect.
We use a mount state flag to record the "bad summary count" state so
that the (subsequent) online fsck patches can detect subtlely incorrect
counts and set the flag; clear it userspace asks for a repair; or force
a recalculation at the next mount if nobody fixes it by unmount time.
Reported-by: Filippo Giunchedi <fgiunchedi@wikimedia.org>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Now that we've shortened everything, fix up all the indentation and
whitespace problems. There are no functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Shorten the name of the online fsck context structure. Whitespace
damage will be fixed by a subsequent patch. There are no functional
changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Shorten all the metadata repair xfs_repair_* symbols to xrep_.
Whitespace damage will be fixed by a subsequent patch. There are no
functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Shorten all the metadata checking xfs_scrub_ prefixes to xchk_. After
this, the only xfs_scrub* symbols are the ones that pertain to both
scrub and repair. Whitespace damage will be fixed in a subsequent
patch. There are no functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Less trivial cleanups of the error argument to xfs_btree_del_cursor;
these require some minor code refactoring.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The error argument to xfs_btree_del_cursor already understands the
"nonzero for error" semantics, so remove pointless error testing in the
callers and pass it directly.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The following assertion was seen on generic/051:
XFS: Assertion failed: tp->t_firstblock == NULLFSBLOCK, file: fs/xfs/libxfs5
------------[ cut here ]------------
kernel BUG at fs/xfs/xfs_message.c:102!
invalid opcode: 0000 [#1] SMP PTI
CPU: 2 PID: 20757 Comm: fsstress Not tainted 4.18.0-rc4+ #3969
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.1-1 04/01/4
RIP: 0010:assfail+0x23/0x30
Code: c3 66 0f 1f 44 00 00 48 89 f1 41 89 d0 48 c7 c6 88 e0 8c 82 48 89 fa
RSP: 0018:ffff88012dc43c08 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff88012dc43ca0 RCX: 0000000000000000
RDX: 00000000ffffffc0 RSI: 000000000000000a RDI: ffffffff828480eb
RBP: ffff88012aa92758 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: f000000000000000 R12: 0000000000000000
R13: ffff88012dc43d48 R14: ffff88013092e7e8 R15: 0000000000000014
FS: 00007f8d689b8e80(0000) GS:ffff88013fd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8d689c7000 CR3: 000000012ba6a000 CR4: 00000000000006e0
Call Trace:
xfs_defer_init+0xff/0x160
xfs_reflink_remap_extent+0x31b/0xa00
xfs_reflink_remap_blocks+0xec/0x4a0
xfs_reflink_remap_range+0x3a1/0x650
xfs_file_dedupe_range+0x39/0x50
vfs_dedupe_file_range+0x218/0x260
do_vfs_ioctl+0x262/0x6a0
? __se_sys_newfstat+0x3c/0x60
ksys_ioctl+0x35/0x60
__x64_sys_ioctl+0x11/0x20
do_syscall_64+0x4b/0x190
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The root cause of the assertion failure is that xfs_defer_finish doesn't
roll the transaction after processing all the deferred items. Therefore
it returns a dirty transaction to the caller, which leaves the caller at
risk of exceeding the transaction reservation if it logs more items.
Brian Foster's patchset to move the defer_ops firstblock into the
transaction requires t_firstblock == NULLFSBLOCK upon defer_ops
initialization, which is how this was noticed at all.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Check the leaf attribute freemap when we're verifying the block.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
qca_open() and qca_set_baudrate() are never called in atomic context.
They call kzalloc() and bt_skb_alloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
inject_cmd_complete() is only called by intel_dequeue(),
which is never called in atomic context.
inject_cmd_complete() calls bt_skb_alloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
inject_cmd_complete() is only called by btusb_send_frame_intel(),
which is set to hdev->send, and hdev->send() is never
called in atomic context.
inject_cmd_complete() calls bt_skb_alloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btmrvl_sdio_card_to_host() is never called in atomic context.
It calls bt_skb_alloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bpa10x_send_frame() is only set to hdev->send, and hdev->send() is never
called in atomic context.
bpa10x_send_frame() calls usb_alloc_urb(), kmalloc() and usb_submit_urb()
with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bluecard_hci_set_baud_rate() is never called in atomic context.
bluecard_hci_set_baud_rate() is only by bluecard_hci_open(), which is
set to hdev->open, and hdev->open() is never called in atomic context.
bluecard_hci_set_baud_rate() calls bt_skb_alloc() with GFP_ATOMIC,
which is not necessary. GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bfusb_send_frame() is only set to hdev->send, and hdev->send() is never
called in atomic context.
bfusb_send_frame() calls bt_skb_alloc() with GFP_ATOMIC, which is not
necessary. GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We have introduce a new return type vm_fault_t for
fault, page_mkwrite and pfn_mkwrite handlers. Update
the document for the same
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The documentation for this parameter said "6 bytes" when "8 bytes" was
intended; correct it.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
A n-bit binary counter can count a maximum of 2^n events and the count
value ranges from 0 to (2^n)-1
Signed-off-by: Siddaraju DH <siddarajudh@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fix a warning whinge from Perl introduced by "scripts: kernel-doc: parse next structs/unions"
Unescaped left brace in regex is deprecated here (and will be fatal in Perl 5.32), passed through in regex; marked by <-- HERE in m/({ <-- HERE [^\{\}]*})/ at ./scripts/kernel-doc line 1155.
Unescaped left brace in regex is deprecated here (and will be fatal in Perl 5.32), passed through in regex; marked by <-- HERE in m/({ <-- HERE )/ at ./scripts/kernel-doc line 1179.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
As the other files are documented explicitly, let's add a
short description for 'trigger' as well.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The per-event files to enable or disable kprobes and uprobes
are named 'enable', not 'enabled'. Fix the corresponding
documentation.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fill in missing documentation for the HardwareCorrupted field in proc.txt.
Signed-off-by: Prashant Dhamdhere <pdhamdhe@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Replace the explicit clock handling to enable/disable the SATA module by
calls to Runtime PM.
This makes the driver independent of actual SoC clock/power hierarchies,
and is needed to support virtualization, where the guest is not in full
control of power management.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As Dave Chinner points out, we don't have a proper documentation for the
ktime_get() family of interfaces, making it rather unclear which of the
over 30 (!) interfaces one should actually use in a driver or elsewhere
in the kernel.
I wrote up an explanation from how I personally see the interfaces,
documenting what each of the functions do and hopefully making it a bit
clearer which should be used where.
This is the first time I tried writing .rst format documentation, so
in addition to any mistakes in the content, I probably also introduce
nonstandard formatting ;-)
I first tried to add an extra section to
Documentation/timers/timekeeping.txt, but this is currently not included
in the generated API, and it seems useful to have the API docs as part
of what gets generated in
https://www.kernel.org/doc/html/latest/core-api/index.html#core-utilities
instead, so I started a new file there.
I also considered adding the documentation inline in the
include/linux/timekeeping.h header, but couldn't figure out how to do
that in a way that would result both in helpful inline comments as
well as readable html output, so I settled for the latter, with
a small note pointing to it from the header.
Cc: Dave Chinner <david@fromorbit.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Hook up arm64 support to the rseq selftests.
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Set possible_clones field to report that the writeback connector and
the one driving the display could be enabled at the same time.
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Older version of this patch series reported writeback as disconnected
to avoid confusing userspace not aware of writeback connectors.
However, the version that got merged uses a special cap
(DRM_CLIENT_CAP_WRITEBACK_CONNECTORS) for this purpose.
This helps us avoid some special handling of writeback connector
in drm_helper_probe_single_connector_modes, see [1].
https://lists.freedesktop.org/archives/dri-devel/2018-July/183144.html
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
This is a fix against the issue that crash dump kernel may hang up
during booting, which can happen on any ACPI-based system with "ACPI
Reclaim Memory."
(kernel messages after panic kicked off kdump)
(snip...)
Bye!
(snip...)
ACPI: Core revision 20170728
pud=000000002e7d0003, *pmd=000000002e7c0003, *pte=00e8000039710707
Internal error: Oops: 96000021 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.14.0-rc6 #1
task: ffff000008d05180 task.stack: ffff000008cc0000
PC is at acpi_ns_lookup+0x25c/0x3c0
LR is at acpi_ds_load1_begin_op+0xa4/0x294
(snip...)
Process swapper/0 (pid: 0, stack limit = 0xffff000008cc0000)
Call trace:
(snip...)
[<ffff0000084a6764>] acpi_ns_lookup+0x25c/0x3c0
[<ffff00000849b4f8>] acpi_ds_load1_begin_op+0xa4/0x294
[<ffff0000084ad4ac>] acpi_ps_build_named_op+0xc4/0x198
[<ffff0000084ad6cc>] acpi_ps_create_op+0x14c/0x270
[<ffff0000084acfa8>] acpi_ps_parse_loop+0x188/0x5c8
[<ffff0000084ae048>] acpi_ps_parse_aml+0xb0/0x2b8
[<ffff0000084a8e10>] acpi_ns_one_complete_parse+0x144/0x184
[<ffff0000084a8e98>] acpi_ns_parse_table+0x48/0x68
[<ffff0000084a82cc>] acpi_ns_load_table+0x4c/0xdc
[<ffff0000084b32f8>] acpi_tb_load_namespace+0xe4/0x264
[<ffff000008baf9b4>] acpi_load_tables+0x48/0xc0
[<ffff000008badc20>] acpi_early_init+0x9c/0xd0
[<ffff000008b70d50>] start_kernel+0x3b4/0x43c
Code: b9008fb9 2a000318 36380054 32190318 (b94002c0)
---[ end trace c46ed37f9651c58e ]---
Kernel panic - not syncing: Fatal exception
Rebooting in 10 seconds..
(diagnosis)
* This fault is a data abort, alignment fault (ESR=0x96000021)
during reading out ACPI table.
* Initial ACPI tables are normally stored in system ram and marked as
"ACPI Reclaim memory" by the firmware.
* After the commit f56ab9a5b73c ("efi/arm: Don't mark ACPI reclaim
memory as MEMBLOCK_NOMAP"), those regions are differently handled
as they are "memblock-reserved", without NOMAP bit.
* So they are now excluded from device tree's "usable-memory-range"
which kexec-tools determines based on a current view of /proc/iomem.
* When crash dump kernel boots up, it tries to accesses ACPI tables by
mapping them with ioremap(), not ioremap_cache(), in acpi_os_ioremap()
since they are no longer part of mapped system ram.
* Given that ACPI accessor/helper functions are compiled in without
unaligned access support (ACPI_MISALIGNMENT_NOT_SUPPORTED),
any unaligned access to ACPI tables can cause a fatal panic.
With this patch, acpi_os_ioremap() always honors memory attribute
information provided by the firmware (EFI) and retaining cacheability
allows the kernel safe access to ACPI tables.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by and Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Under the current implementation, UEFI memory map will be mapped and made
available in virtual mappings only if runtime services are enabled.
But in a later patch, we want to use UEFI memory map in acpi_os_ioremap()
to create mappings of ACPI tables using memory attributes described in
UEFI memory map.
See the following commit:
arm64: acpi: fix alignment fault in accessing ACPI tables
So, as a first step, arm_enter_runtime_services() is modified, alongside
Ard's patch[1], so that UEFI memory map will not be freed even if
efi=noruntime.
[1] https://marc.info/?l=linux-efi&m=152930773507524&w=2
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The BGRT code validates the contents of the table against the UEFI
memory map, and so it expects it to be mapped when the code runs.
On ARM, this is currently not the case, since we tear down the early
mapping after efi_init() completes, and only create the permanent
mapping in arm_enable_runtime_services(), which executes as an early
initcall, but still leaves a window where the UEFI memory map is not
mapped.
So move the call to efi_memmap_unmap() from efi_init() to
arm_enable_runtime_services().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: fold in EFI_MEMMAP attribute check from Ard]
Signed-off-by: Will Deacon <will.deacon@arm.com>
