Remove unnecessary return at end of void function.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch improves the sequence the resources are released by, first,
- disabling the IRQ in the controller, then by
- resetting the DMA logic, and finally, by
- adding a read cycle to ensure that the above commands have been received
before freeing the system interrupt.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes a typo in the error message in pciefd_can_probe().
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This cosmetic change should facilitate in the future the use of MSI
rather than legacy INTx interrupts.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CANFD_IRQ_SET as well as CANFD_TX_PATH_SET are not used.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The embedded firmware aligns its messages on 32-bit boundaries.
This patch makes sure to browse through the list of received messages
while respecting 32-bit alignment.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for Xilinx CAN FD core.
The major difference from the previously supported cores is that there
are TX mailboxes instead of a TX FIFO and the RX FIFO access method is
different.
We only transmit one frame at a time to prevent the HW from reordering
frames (it uses CAN ID priority order).
Support for CAN FD protocol is not added yet.
v2: Removed unnecessary "rx-mode" DT property and wrapped some long
lines.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Xilinx CAN FD cores are different enough from the previous Zynq and AXI
CAN cores that some refactoring of the driver is needed.
This commit contains most of the required refactoring to existing code
and should not alter behavior on existing supported HW.
The changes are:
- Reading and writing to frame registers is parametrized to allow
reading/writing a different frame in the future.
- Slightly misleading (as it did not specify *all* the interrupts
supported by the HW) XCAN_INTR_ALL is replaced with specifying the
interrupts inline in interrupt enabling code.
- xcan_devtype_data.caps is renamed to xcan_devtype_data.flags to allow
for flags that define alternative functionality (e.g. mailboxes vs.
FIFO) instead of purely additive capabilities.
- can_bittiming_const is added to xcan_devtype_data as CAN FD cores will
have wider setting ranges.
- bus_clk clock name is now determined through xcan_devtype_data instead
of comparing compatible string in probe().
- xcan_devtype_data is added to xcan_priv to allow flag checks after
probe().
- XCAN_CAP_WATERMARK is now XCAN_FLAG_TXFEMP. CAN FD cores have
watermark support but no TXFEMP interrupt, which is what we are
actually interested in.
- xcan_start_xmit() is split to in two parts to prepare for TX mailboxes
instead of FIFO in CAN FD cores.
v2: Wrapped some long lines in xcan_write_frame().
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add compatible string and new attributes to support the Xilinx CAN FD
core.
Unlike the previously documented Xilinx CAN cores, the CAN FD core has
TX mailboxes instead of TX FIFO, and optionally RX mailboxes instead of
RX FIFO (selected at core generation time, not switchable at runtime).
Add "tx-mailbox-count" and "rx-mailbox-count" to specify the mailbox
counts instead of reusing "tx-fifo-depth" and "rx-fifo-depth".
The RX FIFO depth is constant 32, but allow it to be specified via
"rx-fifo-depth" to match DT usage with Zynq CAN (which has constant RX
FIFO of depth of 64).
v2: Remove unnecessary "rx-mode" DT property.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver updates stats.tx_bytes in start_xmit() even though it could
do so in TX interrupt handler.
Change the code to update tx_bytes in the interrupt handler, using the
return value of can_get_echo_skb().
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace some custom code with a call to can_change_state().
This subtly changes the error reporting behavior when both RX and TX
error counters indicate the same state.
Previously, if both RX and TX counters indicated the same state:
- if overall state is PASSIVE, report CAN_ERR_CRTL_RX_PASSIVE
- if overall state is WARNING, report CAN_ERR_CRTL_TX_WARNING or
CAN_ERR_CRTL_RX_WARNING depending on which counter is higher,
or CAN_ERR_CRTL_RX_WARNING if the counters have the same value.
After this commit:
- report RX_* or TX_* depending on which counter is higher, or both if
the counters have exactly the same value.
This behavior is consistent with many other CAN drivers that use this
same code pattern.
Tested with the integrated CAN on Zynq-7000 SoC.
v2: Simplify resolving states as suggested by Andri Yngvason.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The xilinx_can driver currently increments error-warning and
error-passive statistics on every error interrupt regardless of whether
the interface was already in the same state. Similarly, the error frame
sent on error interrupts is always sent with
CAN_ERR_CRTL_(RX|TX)_(PASSIVE|WARNING) bit set.
To make the error-warning and error-passive statistics more useful, add
a check to only set the error state when the state has actually been
changed.
Tested with the integrated CAN on Zynq-7000 SoC.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
pcan_add_channels() is never called in atomic context.
pcan_add_channels() is only called by pcan_probe(), which is only set as
".probe" in struct pcmcia_driver.
Despite never getting called from atomic context, pcan_add_channels()
calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
peak_pci_probe() is never called in atomic context.
peak_pci_probe() is set as ".probe" in struct pci_driver.
Despite never getting called from atomic context, peak_pci_probe()
calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The existing SocketCAN implementation provides alloc_candev() to
allocate a CAN device using a single Tx and Rx queue. This can lead to
priority inversion in case the single Tx queue is already full with low
priority messages and a high priority message needs to be sent while the
bus is fully loaded with medium priority messages.
This problem can be solved by using the existing multi-queue support of
the network subsytem. The commit makes it possible to use multi-queue in
the CAN subsystem in the same way it is used in the Ethernet subsystem
by adding an alloc_candev_mqs() call and accompanying macros. With this
support a CAN device can use multi-queue qdisc (e.g. mqprio) to avoid
the aforementioned priority inversion.
The exisiting functionality of alloc_candev() is the same as before.
CAN devices need to have prioritized multiple hardware queues or are
able to abort waiting for arbitration to make sensible use of
multi-queues.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
use helper skb_put_zero to replace the pattern of skb_put() && memset()
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The UCAN driver supports the microcontroller-based USB/CAN
adapters from Theobroma Systems. There are two form-factors
that run essentially the same firmware:
* Seal: standalone USB stick ( https://www.theobroma-systems.com/seal )
* Mule: integrated on the PCB of various System-on-Modules from
Theobroma Systems like the A31-µQ7 and the RK3399-Q7
( https://www.theobroma-systems.com/rk3399-q7 )
The USB wire protocol has been designed to be as generic and
hardware-indendent as possible in the hope of being useful for
implementation on other microcontrollers.
Signed-off-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch sorts the entries in the Kconfig and Makefile alphabetically,
so that further contributors can generate patches more easily.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Trivial fix to spelling mistake in module parameter description text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN error masks header file is in the
include/uapi directory.
Fix the path in the header to the correct location.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This adds a few fixes for things reported since the last merge,
and the latch batch of changes pending for FSI for 4.19.
That batch is a rather mechanical conversion of the misc devices
into proper char devices.
The misc devices were ill suited, the minor space for them is
limited and we can have a lot of chips in a system creating FSI
devices.
This also allows us to better control (and fix) object lifetime
getting rid of the bad devm_kzalloc() of the structures containing
the devices etc...
Finally, we add a chardev to the core FSI that provides raw CFAM
access to FSI slaves as a replacement for the current "raw" binary
sysfs file which will be ultimately deprecated and removed.
-----BEGIN PGP SIGNATURE-----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=ho3P
-----END PGP SIGNATURE-----
Merge tag 'fsi-updates-2018-07-27' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/linux-fsi into char-misc-next
Ben writes:
Last round of FSI updates for 4.19
This adds a few fixes for things reported since the last merge,
and the latch batch of changes pending for FSI for 4.19.
That batch is a rather mechanical conversion of the misc devices
into proper char devices.
The misc devices were ill suited, the minor space for them is
limited and we can have a lot of chips in a system creating FSI
devices.
This also allows us to better control (and fix) object lifetime
getting rid of the bad devm_kzalloc() of the structures containing
the devices etc...
Finally, we add a chardev to the core FSI that provides raw CFAM
access to FSI slaves as a replacement for the current "raw" binary
sysfs file which will be ultimately deprecated and removed.
In case of Device Tree platforms, even though the Samsung PMIC sec
device is instantiated from DT, the driver is still matched through I2C
module alias. That is because I2C core always reports an I2C module
alias instead of DT one.
This could change in the future so export DT module alias.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This fixes kernel crashing on NVIDIA Tegra if kernel is compiled in
a multiplatform configuration and IPMMU-VMSA driver is enabled.
Cc: <stable@vger.kernel.org> # v3.20+
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The Renesas IPMMU-VMSA driver supports not just R-Car H2 and M2 SoCs,
but also other R-Car Gen2 and R-Car Gen3 SoCs.
Drop a superfluous "Renesas" while at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When attaching a device to an IOMMU group with
CONFIG_DEBUG_ATOMIC_SLEEP=y:
BUG: sleeping function called from invalid context at mm/slab.h:421
in_atomic(): 1, irqs_disabled(): 128, pid: 61, name: kworker/1:1
...
Call trace:
...
arm_lpae_alloc_pgtable+0x114/0x184
arm_64_lpae_alloc_pgtable_s1+0x2c/0x128
arm_32_lpae_alloc_pgtable_s1+0x40/0x6c
alloc_io_pgtable_ops+0x60/0x88
ipmmu_attach_device+0x140/0x334
ipmmu_attach_device() takes a spinlock, while arm_lpae_alloc_pgtable()
allocates memory using GFP_KERNEL. Originally, the ipmmu-vmsa driver
had its own custom page table allocation implementation using
GFP_ATOMIC, hence the spinlock was fine.
Fix this by replacing the spinlock by a mutex, like the arm-smmu driver
does.
Fixes: f20ed39f53145e45 ("iommu/ipmmu-vmsa: Use the ARM LPAE page table allocator")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This allows the default behavior to be controlled by a kernel config
option instead of changing the commandline for the kernel to include
"iommu.passthrough=on" or "iommu=pt" on machines where this is desired.
Likewise, for machines where this config option is enabled, it can be
disabled at boot time with "iommu.passthrough=off" or "iommu=nopt".
Also corrected iommu=pt documentation for IA-64, since it has no code that
parses iommu= at all.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
While we could print it at setup time, this is an easier way to match
each device to their default IOMMU allocation type.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
On ams AS3722, power on when AC OK is enabled by default.
Making this option as disable by default and enable only
when platform need this explicitly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Bibek Basu <bbasu@nvidia.com>
Tested-by: Bibek Basu <bbasu@nvidia.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Pine64 H64 board uses an AXP806 PMIC in I2C and self-working mode.
The H64 SoC does not have the usual RSB controller.
This patch adds AXP806 to the list of devices supported in I2C mode.
In theory, all RSB-based PMICs can also be used in I2C mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP806 can operate in a standalone "self-working" mode, in which it
is also responsible for power control of the overall system. This mode
is similar to the master mode, but the EN/PWRON pin functions as a power
button, instead of a level-triggered enable switch.
This patch adds code checking for the new "x-powers,self-working-mode"
property, and a separate mfd_cell list that includes the power button
(PEK) sub-device.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP806 has three operation modes:
- master mode: The PMIC is the first or only AXP PMIC in the system,
but is not in charge of power management, i.e. only
provides regulator functions.
- slave mode: The PMIC is the second AXP PMIC in the system, chained
to the first, or master, one.
- self-working mode: The PMIC is the only AXP PMIC in the system, and
is in charge of power sequencing.
The functional differences between these modes can be found in the
"Control and Operation" chapter of the AXP806 (in Chinese) and AXP805
(in English) datasheets. These include how the PMIC responds to external
signals, whether it takes an external voltage reference or uses its own,
and whether the EN/PWRON pin functions as an enable switch or power button.
We already support both slave and master mode. This patch adds a property
for describing the self-working mode, and reworks the description for
the mode properties.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For designs where CS/ADDR pin is floating, it is useful to
allow dts to define whether to keep internal pull down or not.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Configuring Speaker Mode Pullup was already supported in pdata, but not
in the dts.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
CMD_GET_STATUS is not supported by some devices implementing
RDU2-compatible ICD as well as "legacy" devices. To account for that
fact, add code that obtains the same information (app/bootloader FW
version) using several different commands.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is needed to make rave-sp-wdt driver to properly ping the
watchdog on "legacy" firmware.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is needed to make rave-sp-eeprom driver work on "legacy"
firmware.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Relying on serial port defaults for flow control and parity can result
in complete breakdown of communication with RAVE SP on some platforms
where defaults are not what we need them to be. One such case is
VF610-base ZII SPU3 board (not supported upstream). To avoid this
problem in the future, add code to explicitly configure both.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove unusded defines that are a leftover from earlier iterations of
the driver.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes https://bugs.linaro.org/show_bug.cgi?id=3903
LTP Functional tests have caused a bad paging request when triggering
the regmap_read_debugfs() logic of the device PMIC Hi6553 (reading
regmap/f8000000.pmic/registers file during read_all test):
Unable to handle kernel paging request at virtual address ffff0
[ffff00000984e000] pgd=0000000077ffe803, pud=0000000077ffd803,0
Internal error: Oops: 96000007 [#1] SMP
...
Hardware name: HiKey Development Board (DT)
...
Call trace:
regmap_mmio_read8+0x24/0x40
regmap_mmio_read+0x48/0x70
_regmap_bus_reg_read+0x38/0x48
_regmap_read+0x68/0x170
regmap_read+0x50/0x78
regmap_read_debugfs+0x1a0/0x308
regmap_map_read_file+0x48/0x58
full_proxy_read+0x68/0x98
__vfs_read+0x48/0x80
vfs_read+0x94/0x150
SyS_read+0x6c/0xd8
el0_svc_naked+0x30/0x34
Code: aa1e03e0 d503201f f9400280 8b334000 (39400000)
Investigations have showed that, when triggered by debugfs read()
handler, the mmio regmap logic was reading a bigger (16k) register area
than the one mapped by devm_ioremap_resource() during hi655x-pmic probe
time (4k).
This commit changes hi655x's max register, according to HW specs, to be
the same as the one declared in the pmic device in hi6220's dts, fixing
the issue.
Cc: <stable@vger.kernel.org> #v4.9 #v4.14 #v4.16 #v4.17
Signed-off-by: Rafael David Tinoco <rafael.tinoco@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch fixes documentation of tps65911 because its list of
compatible regulators contains wrongly vdd3 instead of vdd2.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some Arizona CODECs have a small timing window where they will
NAK an I2C transaction if it happens before the boot done bit is
set. This can cause the read of the register containing the boot
done bit to fail until it is set. Since regmap_read_poll_timeout
will abort polling if a read fails it can't be reliably used to
poll the boot done bit over I2C.
Do a partial revert of ef84f885e037 ("mfd: arizona: Refactor
arizona_poll_reg"), removing the regmap_read_poll_timeout but
leaving the refactoring to make the arizona_poll_reg take more
sensible arguments.
Fixes: ef84f885e037 ("mfd: arizona: Refactor arizona_poll_reg")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
