[ Upstream commit 67e2996f72 ]
Each GPIO bank supports a variable number of lines which is usually 16, but
is less in some cases : this is specified by the last argument of the
"gpio-ranges" bank node property.
Report to the framework, the actual number of lines, so the libgpiod
gpioinfo command lists the actually existing GPIO lines.
Fixes: 1dc9d28915 ("pinctrl: stm32: add possibility to use gpio-ranges to declare bank range")
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Link: https://lore.kernel.org/r/20210617144629.2557693-1-fabien.dessenne@foss.st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa0c10a5f3 ]
The Special Function Registers on all Exynos SoC, including ARM64, are
32-bit wide, so entire driver uses matching functions like readl() or
writel(). On 64-bit ARM using unsigned long for register masks:
1. makes little sense as immediately after bitwise operation it will be
cast to 32-bit value when calling writel(),
2. is actually error-prone because it might promote other operands to
64-bit.
Addresses-Coverity: Unintentional integer overflow
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20210408195029.69974-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 196d941753 ]
When updating pin names for Intel Lewisburg, the numbers of pins were
left behind. Update them accordingly.
Fixes: e66ff71fd0 ("pinctrl: lewisburg: Update pin list according to v1.1v6")
Signed-off-by: Yuanyuan Zhong <yzhong@purestorage.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b74e40a4e ]
Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Depends-on: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Depends-on: 827e1579e1 ("pinctrl: baytrail: Rectify debounce support (part 2)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa86fc2e2 ]
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel Merrifield pin control hardware the 20 kOhm sounds plausible
because it gives a good trade off between weakness and minimization of leakage
current (will be only 50 uA with the above choice).
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 156abe2961 upstream
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5 ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812f ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[sudip: use byt_gpio and vg->pdev->dev for dev_info()]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e2b74419e5 upstream
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.
This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3c75e7a93 ]
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel pin control hardware the 5 kOhm sounds plausible
because on one hand it's a minimum of resistors present in all
hardware generations and at the same time it's high enough to minimize
leakage current (will be only 200 uA with the above choice).
Fixes: e57725eabf ("pinctrl: intel: Add support for hardware debouncer")
Reported-by: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f46fe79ff1 ]
This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no
pinctrl_map is added. The current behavior is to return 0 when
!PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry()
incorrectly assumes that a map was added and sets num_maps = 2.
Analysis:
=========
The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf()
if PCS_HAS_PINCONF is enabled. The function pcs_parse_pinconf()
returns 0 to indicate there was no error and num_maps is then set to 2:
980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,
981 struct device_node *np,
982 struct pinctrl_map **map,
983 unsigned *num_maps,
984 const char **pgnames)
985 {
<snip>
1053 (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
1054 (*map)->data.mux.group = np->name;
1055 (*map)->data.mux.function = np->name;
1056
1057 if (PCS_HAS_PINCONF && function) {
1058 res = pcs_parse_pinconf(pcs, np, function, map);
1059 if (res)
1060 goto free_pingroups;
1061 *num_maps = 2;
1062 } else {
1063 *num_maps = 1;
1064 }
However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or
!nconfs. I believe these conditions should indicate that no map was
added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry()
will set num_maps = 2 even though no maps were successfully added, as
it does not reach "m++" on line 940:
895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
896 struct pcs_function *func,
897 struct pinctrl_map **map)
898
899 {
900 struct pinctrl_map *m = *map;
<snip>
917 /* If pinconf isn't supported, don't parse properties in below. */
918 if (!PCS_HAS_PINCONF)
919 return 0;
920
921 /* cacluate how much properties are supported in current node */
922 for (i = 0; i < ARRAY_SIZE(prop2); i++) {
923 if (of_find_property(np, prop2[i].name, NULL))
924 nconfs++;
925 }
926 for (i = 0; i < ARRAY_SIZE(prop4); i++) {
927 if (of_find_property(np, prop4[i].name, NULL))
928 nconfs++;
929 }
930 if (!nconfs)
919 return 0;
932
933 func->conf = devm_kcalloc(pcs->dev,
934 nconfs, sizeof(struct pcs_conf_vals),
935 GFP_KERNEL);
936 if (!func->conf)
937 return -ENOMEM;
938 func->nconfs = nconfs;
939 conf = &(func->conf[0]);
940 m++;
This situtation will cause a boot failure [0] on the BeagleBone Black
(AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi
has compatible = "pinconf-single" instead of "pinctrl-single".
The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF
or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no
map was added.
Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish
between -ENOSUPP and other errors. In the case of -ENOSUPP, num_maps
is set to 1 as it is valid for pinconf to be enabled and a given pin
group to not any pinconf properties.
[0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/
Fixes: 9dddb4df90 ("pinctrl: single: support generic pinconf")
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200608125143.GA2789203@x1
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f354157a7d upstream.
Currently, for EINT_TYPE GPIOs, the CON and FLTCON registers
are saved and restored over a suspend/resume cycle. However, the
EINT_MASK registers are not.
On S5PV210 at the very least, these registers are not retained over
suspend, leading to the interrupts remaining masked upon resume and
therefore no interrupts being triggered for the device. There should
be no effect on any SoCs that do retain these registers as theoretically
we would just be re-writing what was already there.
Fixes: 7ccbc60cd9 ("pinctrl: exynos: Handle suspend/resume of GPIO EINT registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 69388e15f5 ]
According to Braswell NDA Specification Update (#557593),
concurrent read accesses may result in returning 0xffffffff and write
instructions may be dropped. We have an established format for the
commit references, i.e.
cdca06e4e8 ("pinctrl: baytrail: Add missing spinlock usage in
byt_gpio_irq_handler")
Fixes: 0bd50d719b ("pinctrl: cherryview: prevent concurrent access to GPIO controllers")
Signed-off-by: Grace Kao <grace.kao@intel.com>
Reported-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccd025eadd ]
It appears that pin configuration for GPIO chip hasn't been enabled yet
due to absence of ->set_config() callback.
Enable it here for Intel Baytrail.
Fixes: c501d0b149 ("pinctrl: baytrail: Add pin control operations")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02aeb2f215 ]
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
first two CAN outputs.
A closer look reveals other issues:
- Some functionality is available on alternative pins, but the
PINMUX_DATA() entries is using the wrong marks,
- Several configurations are missing.
Fix this by:
- Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and
CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK,
resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the
corresponding enum IDs,
- Adding all missing enum IDs and marks,
- Use the right (*_PJ2x) variants for alternative pins,
- Adding all missing configurations to pinmux_data[],
- Adding all missing function GPIO definitions to pinmux_func_gpios[].
See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00:
[1] Table 1.4 List of Pins
[2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One
Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel
(32 Mailboxes × 1 Channel),
[3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as
One Channel (96 Mailboxes × 1 Channel),
[4] Table 48.3 Multiplexed Pins (Port B),
[5] Table 48.4 Multiplexed Pins (Port C),
[6] Table 48.10 Multiplexed Pins (Port J),
[7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a23680594d ]
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.
This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.
This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().
Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55b1cb1f03 ]
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
two CAN outputs.
Fix this by:
- Renaming CRX0_CRX1_MARK to CTX0_CTX1_MARK, as PJ2MD[2:0]=010
configures the combined "CTX0&CTX1" output signal,
- Renaming CRX0X1_MARK to CRX0_CRX1_MARK, as PJ3MD[1:0]=10 configures
the shared "CRX0/CRX1" input signal, which is fed to both CAN
inputs,
- Adding the missing function GPIO definition for "CTX0&CTX1" to
pinmux_func_gpios[],
- Moving all CAN enums next to each other.
See SH7262 Group, SH7264 Group User's Manual: Hardware, Rev. 4.00:
[1] Figure 1.2 (3) (Pin Assignment for the SH7264 Group (1-Mbyte
Version),
[2] Figure 1.2 (4) Pin Assignment for the SH7264 Group (640-Kbyte
Version,
[3] Table 1.4 List of Pins,
[4] Figure 20.29 Connection Example when Using This Module as 1-Channel
Module (64 Mailboxes x 1 Channel),
[5] Table 32.10 Multiplexed Pins (Port J),
[6] Section 32.2.30 (3) Port J Control Register 0 (PJCR0).
Note that the last 2 disagree about PJ2MD[2:0], which is probably the
root cause of this bug. But considering [4], "CTx0&CTx1" in [5] must
be correct, and "CRx0&CRx1" in [6] must be wrong.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e6e448bdc ]
There are two pin groups for the FSIC SPDIF signal, but the FSIC pin
group array lists only one, and it refers to a nonexistent group.
Fixes: 2ecd4154c9 ("sh-pfc: sh73a0: Add FSI pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9fd50488b ]
The vin1_data18_b pin group itself is present, but it is not listed in
the VIN1 pin group array, and thus cannot be selected.
Fixes: 7dd74bb1f0 ("pinctrl: sh-pfc: r8a7792: Add VIN pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4b0350047 ]
The entry for "scifb2_data_c" in the SCIFB2 pin group array contains a
typo, thus the group cannot be selected.
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ecd8c9cb8 ]
The err_rst_reqb, ext_clki, lowpwr, and ref_clko pin groups are present,
but no pinmux functions refer to them, hence they can not be selected.
Fixes: 1e7d5d849c ("sh-pfc: Add emev2 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d374bacd7 ]
The IP10[5:3] field in Peripheral Function Select Register 10 has a
width of 3 bits, i.e. it allows programming one out of 8 different
configurations.
However, 9 values are provided instead of 8, overflowing into the
subsequent field in the register, and thus breaking the configuration of
the latter.
Fix this by dropping a bogus zero value.
Fixes: ac1ebc2190 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9540cbdfcd ]
The Port C I/O Register 0 contains 7 reserved bits, but the descriptor
contains only dummy configuration values for 6 reserved bits, thus
breaking the configuration of all subsequent fields in the register.
Fix this by adding the two missing configuration values.
Fixes: f5e811f2a4 ("sh-pfc: Add sh7269 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e28dc3f09c ]
While the SEL_PWM[0-3] fields in the Module Select Register 0 support 4
possible configurations per PWM pin, only the first 3 are valid.
Replace the invalid and unused configurations for SEL_PWM[0-3]_3 by
dummies.
Fixes: 794a671176 ("pinctrl: sh-pfc: Initial R8A77995 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94482af705 ]
The Peripheral Function Select Register 11 contains 3 reserved bits and
15 variable-width fields, but the variable field descriptor does not
contain the 3-bit field IP11[25:23].
Fixes: 856cb4bb33 ("sh: Add support pinmux for SH7734")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d6256cb88 ]
The vin1_b_data18_mux[] arrays contains pin marks for the 2 LSB bits of
the color components. The vin1_b_data18_pins[] array rightfully does
not include the corresponding pin numbers, as RGB18 is subset of RGB24,
containing only the 6 MSB bits of each component.
Fixes: 8e32c9671f ("pinctrl: sh-pfc: r8a7791: Add VIN pins")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884fa25fb6 ]
The qspi_data4_b_mux[] array contains pin marks for the clock and chip
select pins. The qspi_data4_b_pins[] array rightfully does not contain
the corresponding pin numbers, as the control pins are provided by a
separate group (qspi_ctrl_b).
Fixes: 2d0c386f13 ("pinctrl: sh-pfc: r8a7791: Add QSPI pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40ecab5512 ]
Commit 39ce8150a0 ("pinctrl: baytrail: Serialize all register access")
added a spinlock around all register accesses because:
"There is a hardware issue in Intel Baytrail where concurrent GPIO register
access might result reads of 0xffffffff and writes might get dropped
completely."
Testing has shown that this does not catch all cases, there are still
2 problems remaining
1) The original fix uses a spinlock per byt_gpio device / struct,
additional testing has shown that this is not sufficient concurent
accesses to 2 different GPIO banks also suffer from the same problem.
This commit fixes this by moving to a single global lock.
2) The original fix did not add a lock around the register accesses in
the suspend/resume handling.
Since pinctrl-baytrail.c is using normal suspend/resume handlers,
interrupts are still enabled during suspend/resume handling. Nothing
should be using the GPIOs when they are being taken down, _but_ the
GPIOs themselves may still cause interrupts, which are likely to
use (read) the triggering GPIO. So we need to protect against
concurrent GPIO register accesses in the suspend/resume handlers too.
This commit fixes this by adding the missing spin_lock / unlock calls.
The 2 fixes together fix the Acer Switch 10 SW5-012 getting completely
confused after a suspend resume. The DSDT for this device has a bug
in its _LID method which reprograms the home and power button trigger-
flags requesting both high and low _level_ interrupts so the IRQs for
these 2 GPIOs continuously fire. This combined with the saving of
registers during suspend, triggers concurrent GPIO register accesses
resulting in saving 0xffffffff as pconf0 value during suspend and then
when restoring this on resume the pinmux settings get all messed up,
resulting in various I2C busses being stuck, the wifi no longer working
and often the tablet simply not coming out of suspend at all.
Cc: stable@vger.kernel.org
Fixes: 39ce8150a0 ("pinctrl: baytrail: Serialize all register access")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Maximilian Luz