[ Upstream commit a6cae77f1b ]
commit 7c6986ade6 ("powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()")
introduces udelay() call without including the linux/delay.h header.
This may happen to work on master but the header that declares the
functionshould be included nonetheless.
Fixes: 7c6986ade6 ("powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210729180103.15578-1-msuchanek@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2fb0a2c989 upstream.
The comment here is wrong, the addi reads from r2 not r12. The code is
correct, 0x38420000 = addi r2,r2,0.
Fixes: a61674bdfc ("powerpc/module: Handle R_PPC64_ENTRY relocations")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bab26238bb ]
printk_safe_flush_on_panic() has special lock breaking code for the case
where we panic()ed with the console lock held. It relies on panic IPI
causing other CPUs to mark themselves offline.
Do as most other architectures do.
This effectively reverts commit de6e5d3841 ("powerpc: smp_send_stop do
not offline stopped CPUs"), unfortunately it may result in some false
positive warnings, but the alternative is more situations where we can
crash without getting messages out.
Fixes: de6e5d3841 ("powerpc: smp_send_stop do not offline stopped CPUs")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210623041245.865134-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7c6986ade6 upstream.
In raise_backtrace_ipi() we iterate through the cpumask of CPUs, sending
each an IPI asking them to do a backtrace, but we don't wait for the
backtrace to happen.
We then iterate through the CPU mask again, and if any CPU hasn't done
the backtrace and cleared itself from the mask, we print a trace on its
behalf, noting that the trace may be "stale".
This works well enough when a CPU is not responding, because in that
case it doesn't receive the IPI and the sending CPU is left to print the
trace. But when all CPUs are responding we are left with a race between
the sending and receiving CPUs, if the sending CPU wins the race then it
will erroneously print a trace.
This leads to spurious "stale" traces from the sending CPU, which can
then be interleaved messily with the receiving CPU, note the CPU
numbers, eg:
[ 1658.929157][ C7] rcu: Stack dump where RCU GP kthread last ran:
[ 1658.929223][ C7] Sending NMI from CPU 7 to CPUs 1:
[ 1658.929303][ C1] NMI backtrace for cpu 1
[ 1658.929303][ C7] CPU 1 didn't respond to backtrace IPI, inspecting paca.
[ 1658.929362][ C1] CPU: 1 PID: 325 Comm: kworker/1:1H Tainted: G W E 5.13.0-rc2+ #46
[ 1658.929405][ C7] irq_soft_mask: 0x01 in_mce: 0 in_nmi: 0 current: 325 (kworker/1:1H)
[ 1658.929465][ C1] Workqueue: events_highpri test_work_fn [test_lockup]
[ 1658.929549][ C7] Back trace of paca->saved_r1 (0xc0000000057fb400) (possibly stale):
[ 1658.929592][ C1] NIP: c00000000002cf50 LR: c008000000820178 CTR: c00000000002cfa0
To fix it, change the logic so that the sending CPU waits 5s for the
receiving CPU to print its trace. If the receiving CPU prints its trace
successfully then the sending CPU just continues, avoiding any spurious
"stale" trace.
This has the added benefit of allowing all CPUs to print their traces in
order and avoids any interleaving of their output.
Fixes: 5cc05910f2 ("powerpc/64s: Wire up arch_trigger_cpumask_backtrace()")
Cc: stable@vger.kernel.org # v4.18+
Reported-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210625140408.3351173-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc7130bf11 ]
The IOMMU table is divided into pools for concurrent mappings and each
pool has a separate spinlock. When taking the ownership of an IOMMU group
to pass through a device to a VM, we lock these spinlocks which triggers
a false negative warning in lockdep (below).
This fixes it by annotating the large pool's spinlock as a nest lock
which makes lockdep not complaining when locking nested locks if
the nest lock is locked already.
===
WARNING: possible recursive locking detected
5.11.0-le_syzkaller_a+fstn1 #100 Not tainted
--------------------------------------------
qemu-system-ppc/4129 is trying to acquire lock:
c0000000119bddb0 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
but task is already holding lock:
c0000000119bdd30 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(p->lock)/1);
lock(&(p->lock)/1);
===
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210301063653.51003-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ef1dd9c7e ]
If identical_pvr_fixup() is not inlined, there are two modpost warnings:
WARNING: modpost: vmlinux.o(.text+0x54e8): Section mismatch in reference
from the function identical_pvr_fixup() to the function
.init.text:of_get_flat_dt_prop()
The function identical_pvr_fixup() references
the function __init of_get_flat_dt_prop().
This is often because identical_pvr_fixup lacks a __init
annotation or the annotation of of_get_flat_dt_prop is wrong.
WARNING: modpost: vmlinux.o(.text+0x551c): Section mismatch in reference
from the function identical_pvr_fixup() to the function
.init.text:identify_cpu()
The function identical_pvr_fixup() references
the function __init identify_cpu().
This is often because identical_pvr_fixup lacks a __init
annotation or the annotation of identify_cpu is wrong.
identical_pvr_fixup() calls two functions marked as __init and is only
called by a function marked as __init so it should be marked as __init
as well. At the same time, remove the inline keywork as it is not
necessary to inline this function. The compiler is still free to do so
if it feels it is worthwhile since commit 889b3c1245 ("compiler:
remove CONFIG_OPTIMIZE_INLINING entirely").
Fixes: 14b3d926a2 ("[POWERPC] 4xx: update 440EP(x)/440GR(x) identical PVR issue workaround")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/1316
Link: https://lore.kernel.org/r/20210302200829.2680663-1-nathan@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5ae5bc12d0 upstream.
During the EEH MMIO error checking, the current implementation fails to map
the (virtual) MMIO address back to the pci device on radix with hugepage
mappings for I/O. This results into failure to dispatch EEH event with no
recovery even when EEH capability has been enabled on the device.
eeh_check_failure(token) # token = virtual MMIO address
addr = eeh_token_to_phys(token);
edev = eeh_addr_cache_get_dev(addr);
if (!edev)
return 0;
eeh_dev_check_failure(edev); <= Dispatch the EEH event
In case of hugepage mappings, eeh_token_to_phys() has a bug in virt -> phys
translation that results in wrong physical address, which is then passed to
eeh_addr_cache_get_dev() to match it against cached pci I/O address ranges
to get to a PCI device. Hence, it fails to find a match and the EEH event
never gets dispatched leaving the device in failed state.
The commit 3343962068 ("powerpc/eeh: Handle hugepages in ioremap space")
introduced following logic to translate virt to phys for hugepage mappings:
eeh_token_to_phys():
+ pa = pte_pfn(*ptep);
+
+ /* On radix we can do hugepage mappings for io, so handle that */
+ if (hugepage_shift) {
+ pa <<= hugepage_shift; <= This is wrong
+ pa |= token & ((1ul << hugepage_shift) - 1);
+ }
This patch fixes the virt -> phys translation in eeh_token_to_phys()
function.
$ cat /sys/kernel/debug/powerpc/eeh_address_cache
mem addr range [0x0000040080000000-0x00000400807fffff]: 0030:01:00.1
mem addr range [0x0000040080800000-0x0000040080ffffff]: 0030:01:00.1
mem addr range [0x0000040081000000-0x00000400817fffff]: 0030:01:00.0
mem addr range [0x0000040081800000-0x0000040081ffffff]: 0030:01:00.0
mem addr range [0x0000040082000000-0x000004008207ffff]: 0030:01:00.1
mem addr range [0x0000040082080000-0x00000400820fffff]: 0030:01:00.0
mem addr range [0x0000040082100000-0x000004008210ffff]: 0030:01:00.1
mem addr range [0x0000040082110000-0x000004008211ffff]: 0030:01:00.0
Above is the list of cached io address ranges of pci 0030:01:00.<fn>.
Before this patch:
Tracing 'arg1' of function eeh_addr_cache_get_dev() during error injection
clearly shows that 'addr=' contains wrong physical address:
kworker/u16:0-7 [001] .... 108.883775: eeh_addr_cache_get_dev:
(eeh_addr_cache_get_dev+0xc/0xf0) addr=0x80103000a510
dmesg shows no EEH recovery messages:
[ 108.563768] bnx2x: [bnx2x_timer:5801(eth2)]MFW seems hanged: drv_pulse (0x9ae) != mcp_pulse (0x7fff)
[ 108.563788] bnx2x: [bnx2x_hw_stats_update:870(eth2)]NIG timer max (4294967295)
[ 108.883788] bnx2x: [bnx2x_acquire_hw_lock:2013(eth1)]lock_status 0xffffffff resource_bit 0x1
[ 108.884407] bnx2x 0030:01:00.0 eth1: MDC/MDIO access timeout
[ 108.884976] bnx2x 0030:01:00.0 eth1: MDC/MDIO access timeout
<..>
After this patch:
eeh_addr_cache_get_dev() trace shows correct physical address:
<idle>-0 [001] ..s. 1043.123828: eeh_addr_cache_get_dev:
(eeh_addr_cache_get_dev+0xc/0xf0) addr=0x40080bc7cd8
dmesg logs shows EEH recovery getting triggerred:
[ 964.323980] bnx2x: [bnx2x_timer:5801(eth2)]MFW seems hanged: drv_pulse (0x746f) != mcp_pulse (0x7fff)
[ 964.323991] EEH: Recovering PHB#30-PE#10000
[ 964.324002] EEH: PE location: N/A, PHB location: N/A
[ 964.324006] EEH: Frozen PHB#30-PE#10000 detected
<..>
Fixes: 3343962068 ("powerpc/eeh: Handle hugepages in ioremap space")
Cc: stable@vger.kernel.org # v5.3+
Reported-by: Dominic DeMarco <ddemarc@us.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/161821396263.48361.2796709239866588652.stgit@jupiter
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Thomas Gleixner <tglx@linutronix.de>
commit 6553896666 upstream.
Some code pathes, especially the low level entry code, must be protected
against instrumentation for various reasons:
- Low level entry code can be a fragile beast, especially on x86.
- With NO_HZ_FULL RCU state needs to be established before using it.
Having a dedicated section for such code allows to validate with tooling
that no unsafe functions are invoked.
Add the .noinstr.text section and the noinstr attribute to mark
functions. noinstr implies notrace. Kprobes will gain a section check
later.
Provide also a set of markers: instrumentation_begin()/end()
These are used to mark code inside a noinstr function which calls
into regular instrumentable text section as safe.
The instrumentation markers are only active when CONFIG_DEBUG_ENTRY is
enabled as the end marker emits a NOP to prevent the compiler from merging
the annotation points. This means the objtool verification requires a
kernel compiled with this option.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200505134100.075416272@linutronix.de
[Nicolas:
Guard noinstr macro in include/linux/compiler_types.h in __KERNEL__
&& !__ASSEMBLY__, otherwise noinstr is expanded in the linker
script construct.
Upstream does not have this problem as many macros were moved by
commit 71391bdd2e ("include/linux/compiler_types.h: don't pollute
userspace with macro definitions"). We take the minimal approach here
and just guard the new macro.
Minor context conflicts in:
arch/powerpc/kernel/vmlinux.lds.S
include/asm-generic/vmlinux.lds.h
include/linux/compiler.h]
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5537fcb319 ]
On many powerpc platforms the discovery and initalisation of
pci_controllers (PHBs) happens inside of setup_arch(). This is very early
in boot (pre-initcalls) and means that we're initialising the PHB long
before many basic kernel services (slab allocator, debugfs, a real ioremap)
are available.
On PowerNV this causes an additional problem since we map the PHB registers
with ioremap(). As of commit d538aadc27 ("powerpc/ioremap: warn on early
use of ioremap()") a warning is printed because we're using the "incorrect"
API to setup and MMIO mapping in searly boot. The kernel does provide
early_ioremap(), but that is not intended to create long-lived MMIO
mappings and a seperate warning is printed by generic code if
early_ioremap() mappings are "leaked."
This is all fixable with dumb hacks like using early_ioremap() to setup
the initial mapping then replacing it with a real ioremap later on in
boot, but it does raise the question: Why the hell are we setting up the
PHB's this early in boot?
The old and wise claim it's due to "hysterical rasins." Aside from amused
grapes there doesn't appear to be any real reason to maintain the current
behaviour. Already most of the newer embedded platforms perform PHB
discovery in an arch_initcall and between the end of setup_arch() and the
start of initcalls none of the generic kernel code does anything PCI
related. On powerpc scanning PHBs occurs in a subsys_initcall so it should
be possible to move the PHB discovery to a core, postcore or arch initcall.
This patch adds the ppc_md.discover_phbs hook and a core_initcall stub that
calls it. The core_initcalls are the earliest to be called so this will
any possibly issues with dependency between initcalls. This isn't just an
academic issue either since on pseries and PowerNV EEH init occurs in an
arch_initcall and depends on the pci_controllers being available, similarly
the creation of pci_dns occurs at core_initcall_sync (i.e. between core and
postcore initcalls). These problems need to be addressed seperately.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Make discover_phbs() static]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201103043523.916109-1-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f10881a46f upstream.
Commit bd59380c5b ("powerpc/rtas: Restrict RTAS requests from userspace")
introduced the following error when invoking the errinjct userspace
tool:
[root@ltcalpine2-lp5 librtas]# errinjct open
[327884.071171] sys_rtas: RTAS call blocked - exploit attempt?
[327884.071186] sys_rtas: token=0x26, nargs=0 (called by errinjct)
errinjct: Could not open RTAS error injection facility
errinjct: librtas: open: Unexpected I/O error
The entry for ibm,open-errinjct in rtas_filter array has a typo where
the "j" is omitted in the rtas call name. After fixing this typo the
errinjct tool functions again as expected.
[root@ltcalpine2-lp5 linux]# errinjct open
RTAS error injection facility open, token = 1
Fixes: bd59380c5b ("powerpc/rtas: Restrict RTAS requests from userspace")
Cc: stable@vger.kernel.org
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201208195434.8289-1-tyreld@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c0b976bf2 ]
Currently in generic_secondary_smp_init(), cur_cpu_spec->cpu_restore()
is called before a stack has been set up in r1. This was previously fine
as the cpu_restore() functions were implemented in assembly and did not
use a stack. However commit 5a61ef74f2 ("powerpc/64s: Support new
device tree binding for discovering CPU features") used
__restore_cpu_cpufeatures() as the cpu_restore() function for a
device-tree features based cputable entry. This is a C function and
hence uses a stack in r1.
generic_secondary_smp_init() is entered on the secondary cpus via the
primary cpu using the OPAL call opal_start_cpu(). In OPAL, each hardware
thread has its own stack. The OPAL call is ran in the primary's hardware
thread. During the call, a job is scheduled on a secondary cpu that will
start executing at the address of generic_secondary_smp_init(). Hence
the value that will be left in r1 when the secondary cpu enters the
kernel is part of that secondary cpu's individual OPAL stack. This means
that __restore_cpu_cpufeatures() will write to that OPAL stack. This is
not horribly bad as each hardware thread has its own stack and the call
that enters the kernel from OPAL never returns, but it is still wrong
and should be corrected.
Create the temp kernel stack before calling cpu_restore().
As noted by mpe, for a kexec boot, the secondary CPUs are released from
the spin loop at address 0x60 by smp_release_cpus() and then jump to
generic_secondary_smp_init(). The call to smp_release_cpus() is in
setup_arch(), and it comes before the call to emergency_stack_init().
emergency_stack_init() allocates an emergency stack in the PACA for each
CPU. This address in the PACA is what is used to set up the temp kernel
stack in generic_secondary_smp_init(). Move releasing the secondary CPUs
to after the PACAs have been allocated an emergency stack, otherwise the
PACA stack pointer will contain garbage and hence the temp kernel stack
created from it will be broken.
Fixes: 5a61ef74f2 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201014072837.24539-1-jniethe5@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 29daf869cb upstream.
The kernel expects pte_young() to work regardless of CONFIG_SWAP.
Make sure a minor fault is taken to set _PAGE_ACCESSED when it
is not already set, regardless of the selection of CONFIG_SWAP.
This adds at least 3 instructions to the TLB miss exception
handlers fast path. Following patch will reduce this overhead.
Also update the rotation instruction to the correct number of bits
to reflect all changes done to _PAGE_ACCESSED over time.
Fixes: d069cb4373 ("powerpc/8xx: Don't touch ACCESSED when no SWAP.")
Fixes: 5f356497c3 ("powerpc/8xx: remove unused _PAGE_WRITETHRU")
Fixes: e0a8e0d90a ("powerpc/8xx: Handle PAGE_USER via APG bits")
Fixes: 5b2753fc3e ("powerpc/8xx: Implementation of PAGE_EXEC")
Fixes: a891c43b97 ("powerpc/8xx: Prepare handlers for _PAGE_HUGE for 512k pages.")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/af834e8a0f1fa97bfae65664950f0984a70c4750.1602492856.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a32a7e78b upstream.
IBM Power9 processors can speculatively operate on data in the L1 cache before
it has been completely validated, via a way-prediction mechanism. It is not possible
for an attacker to determine the contents of impermissible memory using this method,
since these systems implement a combination of hardware and software security measures
to prevent scenarios where protected data could be leaked.
However these measures don't address the scenario where an attacker induces
the operating system to speculatively execute instructions using data that the
attacker controls. This can be used for example to speculatively bypass "kernel
user access prevention" techniques, as discovered by Anthony Steinhauser of
Google's Safeside Project. This is not an attack by itself, but there is a possibility
it could be used in conjunction with side-channels or other weaknesses in the
privileged code to construct an attack.
This issue can be mitigated by flushing the L1 cache between privilege boundaries
of concern. This patch flushes the L1 cache after user accesses.
This is part of the fix for CVE-2020-4788.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f79643787e upstream.
IBM Power9 processors can speculatively operate on data in the L1 cache before
it has been completely validated, via a way-prediction mechanism. It is not possible
for an attacker to determine the contents of impermissible memory using this method,
since these systems implement a combination of hardware and software security measures
to prevent scenarios where protected data could be leaked.
However these measures don't address the scenario where an attacker induces
the operating system to speculatively execute instructions using data that the
attacker controls. This can be used for example to speculatively bypass "kernel
user access prevention" techniques, as discovered by Anthony Steinhauser of
Google's Safeside Project. This is not an attack by itself, but there is a possibility
it could be used in conjunction with side-channels or other weaknesses in the
privileged code to construct an attack.
This issue can be mitigated by flushing the L1 cache between privilege boundaries
of concern. This patch flushes the L1 cache on kernel entry.
This is part of the fix for CVE-2020-4788.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(backport only)
We're about to grow the exception handlers, which will make a bunch of them
no longer fit within the space available. We move them out of line.
This is a fiddly and error-prone business, so in the interests of reviewability
I haven't merged this in with the addition of the entry flush.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1da4a0272c upstream.
__get_user_atomic_128_aligned() stores to kaddr using stvx which is a
VMX store instruction, hence kaddr must be 16 byte aligned otherwise
the store won't occur as expected.
Unfortunately when we call __get_user_atomic_128_aligned() in
p9_hmi_special_emu(), the buffer we pass as kaddr (ie. vbuf) isn't
guaranteed to be 16B aligned. This means that the write to vbuf in
__get_user_atomic_128_aligned() has the bottom bits of the address
truncated. This results in other local variables being
overwritten. Also vbuf will not contain the correct data which results
in the userspace emulation being wrong and hence undetected user data
corruption.
In the past we've been mostly lucky as vbuf has ended up aligned but
this is fragile and isn't always true. CONFIG_STACKPROTECTOR in
particular can change the stack arrangement enough that our luck runs
out.
This issue only occurs on POWER9 Nimbus <= DD2.1 bare metal.
The fix is to align vbuf to a 16 byte boundary.
Fixes: 5080332c2c ("powerpc/64s: Add workaround for P9 vector CI load issue")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201013043741.743413-1-mikey@neuling.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd59380c5b upstream.
A number of userspace utilities depend on making calls to RTAS to retrieve
information and update various things.
The existing API through which we expose RTAS to userspace exposes more
RTAS functionality than we actually need, through the sys_rtas syscall,
which allows root (or anyone with CAP_SYS_ADMIN) to make any RTAS call they
want with arbitrary arguments.
Many RTAS calls take the address of a buffer as an argument, and it's up to
the caller to specify the physical address of the buffer as an argument. We
allocate a buffer (the "RMO buffer") in the Real Memory Area that RTAS can
access, and then expose the physical address and size of this buffer in
/proc/powerpc/rtas/rmo_buffer. Userspace is expected to read this address,
poke at the buffer using /dev/mem, and pass an address in the RMO buffer to
the RTAS call.
However, there's nothing stopping the caller from specifying whatever
address they want in the RTAS call, and it's easy to construct a series of
RTAS calls that can overwrite arbitrary bytes (even without /dev/mem
access).
Additionally, there are some RTAS calls that do potentially dangerous
things and for which there are no legitimate userspace use cases.
In the past, this would not have been a particularly big deal as it was
assumed that root could modify all system state freely, but with Secure
Boot and lockdown we need to care about this.
We can't fundamentally change the ABI at this point, however we can address
this by implementing a filter that checks RTAS calls against a list
of permitted calls and forces the caller to use addresses within the RMO
buffer.
The list is based off the list of calls that are used by the librtas
userspace library, and has been tested with a number of existing userspace
RTAS utilities. For compatibility with any applications we are not aware of
that require other calls, the filter can be turned off at build time.
Cc: stable@vger.kernel.org
Reported-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200820044512.7543-1-ajd@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 66943005cc ]
According to the MPC750 Users Manual, the SITV value in Thermal
Management Register 3 is 13 bits long. The present code calculates the
SITV value as 60 * 500 cycles. This would overflow to give 10 us on
a 500 MHz CPU rather than the intended 60 us. (But according to the
Microprocessor Datasheet, there is also a factor of 266 that has to be
applied to this value on certain parts i.e. speed sort above 266 MHz.)
Always use the maximum cycle count, as recommended by the Datasheet.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/896f542e5f0f1d6cf8218524c2b67d79f3d69b3c.1599260540.git.fthain@telegraphics.com.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e0942c030 ]
Many drivers don't check for errors when they get a 0xFFs response from an
MMIO load. As a result after an EEH event occurs a driver can get stuck in
a polling loop unless it some kind of internal timeout logic.
Currently EEH tries to detect and report stuck drivers by dumping a stack
trace after eeh_dev_check_failure() is called EEH_MAX_FAILS times on an
already frozen PE. The value of EEH_MAX_FAILS was chosen so that a dump
would occur every few seconds if the driver was spinning in a loop. This
results in a lot of spurious stack traces in the kernel log.
Fix this by limiting it to printing one stack trace for each PE freeze. If
the driver is truely stuck the kernel's hung task detector is better suited
to reporting the probelm anyway.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Tested-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191016012536.22588-1-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 437ef802e0 upstream.
There are 2 problems with it:
1. "<" vs expected "<<"
2. the shift number is an IOMMU page number mask, not an address
mask as the IOMMU page shift is missing.
This did not hit us before f1565c24b5 ("powerpc: use the generic
dma_ops_bypass mode") because we had additional code to handle bypass
mask so this chunk (almost?) never executed.However there were
reports that aacraid does not work with "iommu=nobypass".
After f1565c24b5, aacraid (and probably others which call
dma_get_required_mask() before setting the mask) was unable to enable
64bit DMA and fall back to using IOMMU which was known not to work,
one of the problems is double free of an IOMMU page.
This fixes DMA for aacraid, both with and without "iommu=nobypass" in
the kernel command line. Verified with "stress-ng -d 4".
Fixes: 6a5c7be5e4 ("powerpc: Override dma_get_required_mask by platform hook and ops")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200908015106.79661-1-aik@ozlabs.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0828137e8f upstream.
__init_FSCR() was added originally in commit 2468dcf641 ("powerpc:
Add support for context switching the TAR register") (Feb 2013), and
only set FSCR_TAR.
At that point FSCR (Facility Status and Control Register) was not
context switched, so the setting was permanent after boot.
Later we added initialisation of FSCR_DSCR to __init_FSCR(), in commit
54c9b2253d ("powerpc: Set DSCR bit in FSCR setup") (Mar 2013), again
that was permanent after boot.
Then commit 2517617e0d ("powerpc: Fix context switch DSCR on
POWER8") (Aug 2013) added a limited context switch of FSCR, just the
FSCR_DSCR bit was context switched based on thread.dscr_inherit. That
commit said "This clears the H/FSCR DSCR bit initially", but it
didn't, it left the initialisation of FSCR_DSCR in __init_FSCR().
However the initial context switch from init_task to pid 1 would clear
FSCR_DSCR because thread.dscr_inherit was 0.
That commit also introduced the requirement that FSCR_DSCR be clear
for user processes, so that we can take the facility unavailable
interrupt in order to manage dscr_inherit.
Then in commit 152d523e63 ("powerpc: Create context switch helpers
save_sprs() and restore_sprs()") (Dec 2015) FSCR was added to
thread_struct. However it still wasn't fully context switched, we just
took the existing value and set FSCR_DSCR if the new thread had
dscr_inherit set. FSCR was still initialised at boot to FSCR_DSCR |
FSCR_TAR, but that value was not propagated into the thread_struct, so
the initial context switch set FSCR_DSCR back to 0.
Finally commit b57bd2de8c ("powerpc: Improve FSCR init and context
switching") (Jun 2016) added a full context switch of the FSCR, and
added an initialisation of init_task.thread.fscr to FSCR_TAR |
FSCR_EBB, but omitted FSCR_DSCR.
The end result is that swapper runs with FSCR_DSCR set because of the
initialisation in __init_FSCR(), but no other processes do, they use
the value from init_task.thread.fscr.
Having FSCR_DSCR set for swapper allows it to access SPR 3 from
userspace, but swapper never runs userspace, so it has no useful
effect. It's also confusing to have the value initialised in two
places to two different values.
So remove FSCR_DSCR from __init_FSCR(), this at least gets us to the
point where there's a single value of FSCR, even if it's still set in
two places.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200527145843.2761782-1-mpe@ellerman.id.au
Cc: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9f675f950 ]
The code in vdso_cpu_init that exposes the cpu and numa node to
userspace via SPRG_VDSO incorrctly masks the cpu to 12 bits. This means
that any kernel running on a box with more than 4096 threads (NR_CPUS
advertises a limit of of 8192 cpus) would expose userspace to two cpu
contexts running at the same time with the same cpu number.
Note: I'm not aware of any distro shipping a kernel with support for more
than 4096 threads today, nor of any system image that currently exceeds
4096 threads. Found via code browsing.
Fixes: 18ad51dd34 ("powerpc: Add VDSO version of getcpu")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200715233704.1352257-1-anton@ozlabs.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ffa8b7dc1 ]
Aneesh increased the size of struct pt_regs by 16 bytes and started
seeing this WARN_ON:
smp: Bringing up secondary CPUs ...
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at arch/powerpc/kernel/process.c:455 giveup_all+0xb4/0x110
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.7.0-rc2-gcc-8.2.0-1.g8f6a41f-default+ #318
NIP: c00000000001a2b4 LR: c00000000001a29c CTR: c0000000031d0000
REGS: c0000000026d3980 TRAP: 0700 Not tainted (5.7.0-rc2-gcc-8.2.0-1.g8f6a41f-default+)
MSR: 800000000282b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 48048224 XER: 00000000
CFAR: c000000000019cc8 IRQMASK: 1
GPR00: c00000000001a264 c0000000026d3c20 c0000000026d7200 800000000280b033
GPR04: 0000000000000001 0000000000000000 0000000000000077 30206d7372203164
GPR08: 0000000000002000 0000000002002000 800000000280b033 3230303030303030
GPR12: 0000000000008800 c0000000031d0000 0000000000800050 0000000002000066
GPR16: 000000000309a1a0 000000000309a4b0 000000000309a2d8 000000000309a890
GPR20: 00000000030d0098 c00000000264da40 00000000fd620000 c0000000ff798080
GPR24: c00000000264edf0 c0000001007469f0 00000000fd620000 c0000000020e5e90
GPR28: c00000000264edf0 c00000000264d200 000000001db60000 c00000000264d200
NIP [c00000000001a2b4] giveup_all+0xb4/0x110
LR [c00000000001a29c] giveup_all+0x9c/0x110
Call Trace:
[c0000000026d3c20] [c00000000001a264] giveup_all+0x64/0x110 (unreliable)
[c0000000026d3c90] [c00000000001ae34] __switch_to+0x104/0x480
[c0000000026d3cf0] [c000000000e0b8a0] __schedule+0x320/0x970
[c0000000026d3dd0] [c000000000e0c518] schedule_idle+0x38/0x70
[c0000000026d3df0] [c00000000019c7c8] do_idle+0x248/0x3f0
[c0000000026d3e70] [c00000000019cbb8] cpu_startup_entry+0x38/0x40
[c0000000026d3ea0] [c000000000011bb0] rest_init+0xe0/0xf8
[c0000000026d3ed0] [c000000002004820] start_kernel+0x990/0x9e0
[c0000000026d3f90] [c00000000000c49c] start_here_common+0x1c/0x400
Which was unexpected. The warning is checking the thread.regs->msr
value of the task we are switching from:
usermsr = tsk->thread.regs->msr;
...
WARN_ON((usermsr & MSR_VSX) && !((usermsr & MSR_FP) && (usermsr & MSR_VEC)));
ie. if MSR_VSX is set then both of MSR_FP and MSR_VEC are also set.
Dumping tsk->thread.regs->msr we see that it's: 0x1db60000
Which is not a normal looking MSR, in fact the only valid bit is
MSR_VSX, all the other bits are reserved in the current definition of
the MSR.
We can see from the oops that it was swapper/0 that we were switching
from when we hit the warning, ie. init_task. So its thread.regs points
to the base (high addresses) in init_stack.
Dumping the content of init_task->thread.regs, with the members of
pt_regs annotated (the 16 bytes larger version), we see:
0000000000000000 c000000002780080 gpr[0] gpr[1]
0000000000000000 c000000002666008 gpr[2] gpr[3]
c0000000026d3ed0 0000000000000078 gpr[4] gpr[5]
c000000000011b68 c000000002780080 gpr[6] gpr[7]
0000000000000000 0000000000000000 gpr[8] gpr[9]
c0000000026d3f90 0000800000002200 gpr[10] gpr[11]
c000000002004820 c0000000026d7200 gpr[12] gpr[13]
000000001db60000 c0000000010aabe8 gpr[14] gpr[15]
c0000000010aabe8 c0000000010aabe8 gpr[16] gpr[17]
c00000000294d598 0000000000000000 gpr[18] gpr[19]
0000000000000000 0000000000001ff8 gpr[20] gpr[21]
0000000000000000 c00000000206d608 gpr[22] gpr[23]
c00000000278e0cc 0000000000000000 gpr[24] gpr[25]
000000002fff0000 c000000000000000 gpr[26] gpr[27]
0000000002000000 0000000000000028 gpr[28] gpr[29]
000000001db60000 0000000004750000 gpr[30] gpr[31]
0000000002000000 000000001db60000 nip msr
0000000000000000 0000000000000000 orig_r3 ctr
c00000000000c49c 0000000000000000 link xer
0000000000000000 0000000000000000 ccr softe
0000000000000000 0000000000000000 trap dar
0000000000000000 0000000000000000 dsisr result
0000000000000000 0000000000000000 ppr kuap
0000000000000000 0000000000000000 pad[2] pad[3]
This looks suspiciously like stack frames, not a pt_regs. If we look
closely we can see return addresses from the stack trace above,
c000000002004820 (start_kernel) and c00000000000c49c (start_here_common).
init_task->thread.regs is setup at build time in processor.h:
#define INIT_THREAD { \
.ksp = INIT_SP, \
.regs = (struct pt_regs *)INIT_SP - 1, /* XXX bogus, I think */ \
The early boot code where we setup the initial stack is:
LOAD_REG_ADDR(r3,init_thread_union)
/* set up a stack pointer */
LOAD_REG_IMMEDIATE(r1,THREAD_SIZE)
add r1,r3,r1
li r0,0
stdu r0,-STACK_FRAME_OVERHEAD(r1)
Which creates a stack frame of size 112 bytes (STACK_FRAME_OVERHEAD).
Which is far too small to contain a pt_regs.
So the result is init_task->thread.regs is pointing at some stack
frames on the init stack, not at a pt_regs.
We have gotten away with this for so long because with pt_regs at its
current size the MSR happens to point into the first frame, at a
location that is not written to by the early asm. With the 16 byte
expansion the MSR falls into the second frame, which is used by the
compiler, and collides with a saved register that tends to be
non-zero.
As far as I can see this has been wrong since the original merge of
64-bit ppc support, back in 2002.
Conceptually swapper should have no regs, it never entered from
userspace, and in fact that's what we do on 32-bit. It's also
presumably what the "bogus" comment is referring to.
So I think the right fix is to just not-initialise regs at all. I'm
slightly worried this will break some code that isn't prepared for a
NULL regs, but we'll have to see.
Remove the comment in head_64.S which refers to us setting up the
regs (even though we never did), and is otherwise not really accurate
any more.
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200428123130.73078-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be5470e0c2 ]
'mem=" option is an easy way to put high pressure on memory during
some test. Hence after applying the memory limit, instead of total
mem, the actual usable memory should be considered when reserving mem
for crashkernel. Otherwise the boot up may experience OOM issue.
E.g. it would reserve 4G prior to the change and 512M afterward, if
passing
crashkernel="2G-4G:384M,4G-16G:512M,16G-64G:1G,64G-128G:2G,128G-:4G",
and mem=5G on a 256G machine.
This issue is powerpc specific because it puts higher priority on
fadump and kdump reservation than on "mem=". Referring the following
code:
if (fadump_reserve_mem() == 0)
reserve_crashkernel();
...
/* Ensure that total memory size is page-aligned. */
limit = ALIGN(memory_limit ?: memblock_phys_mem_size(), PAGE_SIZE);
memblock_enforce_memory_limit(limit);
While on other arches, the effect of "mem=" takes a higher priority
and pass through memblock_phys_mem_size() before calling
reserve_crashkernel().
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Reviewed-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1585749644-4148-1-git-send-email-kernelfans@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 912c0a7f2b upstream.
At boot the FSCR is initialised via one of two paths. On most systems
it's set to a hard coded value in __init_FSCR().
On newer skiboot systems we use the device tree CPU features binding,
where firmware can tell Linux what bits to set in FSCR (and HFSCR).
In both cases the value that's configured at boot is not propagated
into the init_task.thread.fscr value prior to the initial fork of init
(pid 1), which means the value is not used by any processes other than
swapper (the idle task).
For the __init_FSCR() case this is OK, because the value in
init_task.thread.fscr is initialised to something sensible. However it
does mean that the value set in __init_FSCR() is not used other than
for swapper, which is odd and confusing.
The bigger problem is for the device tree CPU features case it
prevents firmware from setting (or clearing) FSCR bits for use by user
space. This means all existing kernels can not have features
enabled/disabled by firmware if those features require
setting/clearing FSCR bits.
We can handle both cases by saving the FSCR value into
init_task.thread.fscr after we have initialised it at boot. This fixes
the bug for device tree CPU features, and will allow us to simplify
the initialisation for the __init_FSCR() case in a future patch.
Fixes: 5a61ef74f2 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200527145843.2761782-3-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 993e3d96fd upstream.
The device tree CPU features binding includes FSCR bit numbers which
Linux is instructed to set by firmware.
Whether that's a good idea or not, in the case of the DSCR the Linux
implementation has a hard requirement that the FSCR_DSCR bit not be
set by default. We use it to track when a process reads/writes to
DSCR, so it must be clear to begin with.
So if firmware tells us to set FSCR_DSCR we must ignore it.
Currently this does not cause a bug in our DSCR handling because the
value of FSCR that the device tree CPU features code establishes is
only used by swapper. All other tasks use the value hard coded in
init_task.thread.fscr.
However we'd like to fix that in a future commit, at which point this
will become necessary.
Fixes: 5a61ef74f2 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200527145843.2761782-2-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dead1c845d upstream.
The pseries platform uses the PCI_PROBE_DEVTREE method of PCI probing
which reads "assigned-addresses" of every PCI device and initializes
the device resources. However if the property is missing or zero sized,
then there is no fallback of any kind and the PCI resources remain
undiscovered, i.e. pdev->resource[] array remains empty.
This adds a fallback which parses the "reg" property in pretty much same
way except it marks resources as "unset" which later make Linux assign
those resources proper addresses.
This has an effect when:
1. a hypervisor failed to assign any resource for a device;
2. /chosen/linux,pci-probe-only=0 is in the DT so the system may try
assigning a resource.
Neither is likely to happen under PowerVM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94c0b013c9 upstream.
If {i,d}-cache-block-size is set and {i,d}-cache-line-size is not, use
the block-size value for both. Per the devicetree spec cache-line-size
is only needed if it differs from the block size.
Originally the code would fallback from block size to line size. An
error message was printed if both properties were missing.
Later the code was refactored to use clearer names and logic but it
inadvertently made line size a required property, meaning on systems
without a line size property we fall back to the default from the
cputable.
On powernv (OPAL) platforms, since the introduction of device tree CPU
features (5a61ef74f2 ("powerpc/64s: Support new device tree binding
for discovering CPU features")), that has led to the wrong value being
used, as the fallback value is incorrect for Power8/Power9 CPUs.
The incorrect values flow through to the VDSO and also to the sysconf
values, SC_LEVEL1_ICACHE_LINESIZE etc.
Fixes: bd067f83b0 ("powerpc/64: Fix naming of cache block vs. cache line")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reported-by: Qian Cai <cai@lca.pw>
[mpe: Add even more detail to change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200416221908.7886-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit abc3fce76a ]
This reverts commit ebb37cf3ff.
That commit does not play well with soft-masked irq state
manipulations in idle, interrupt replay, and possibly others due to
tracing code sometimes using irq_work_queue (e.g., in
trace_hardirqs_on()). That can cause PACA_IRQ_DEC to become set when
it is not expected, and be ignored or cleared or cause warnings.
The net result seems to be missing an irq_work until the next timer
interrupt in the worst case which is usually not going to be noticed,
however it could be a long time if the tick is disabled, which is
against the spirit of irq_work and might cause real problems.
The idea is still solid, but it would need more work. It's not really
clear if it would be worth added complexity, so revert this for
now (not a straight revert, but replace with a comment explaining why
we might see interrupts happening, and gives git blame something to
find).
Fixes: ebb37cf3ff ("powerpc/64: irq_work avoid interrupt when called with hardware irqs enabled")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200402120401.1115883-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c7def7fbde upstream.
In restore_tm_sigcontexts() we take the trap value directly from the
user sigcontext with no checking:
err |= __get_user(regs->trap, &sc->gp_regs[PT_TRAP]);
This means we can be in the kernel with an arbitrary regs->trap value.
Although that's not immediately problematic, there is a risk we could
trigger one of the uses of CHECK_FULL_REGS():
#define CHECK_FULL_REGS(regs) BUG_ON(regs->trap & 1)
It can also cause us to unnecessarily save non-volatile GPRs again in
save_nvgprs(), which shouldn't be problematic but is still wrong.
It's also possible it could trick the syscall restart machinery, which
relies on regs->trap not being == 0xc00 (see 9a81c16b52 ("powerpc:
fix double syscall restarts")), though I haven't been able to make
that happen.
Finally it doesn't match the behaviour of the non-TM case, in
restore_sigcontext() which zeroes regs->trap.
So change restore_tm_sigcontexts() to zero regs->trap.
This was discovered while testing Nick's upcoming rewrite of the
syscall entry path. In that series the call to save_nvgprs() prior to
signal handling (do_notify_resume()) is removed, which leaves the
low-bit of regs->trap uncleared which can then trigger the FULL_REGS()
WARNs in setup_tm_sigcontexts().
Fixes: 2b0a576d15 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200401023836.3286664-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53a712bae5 upstream.
In order to implement KUAP (Kernel Userspace Access Protection) on
Power9 we will be using the AMR, and therefore indirectly the
UAMOR/AMOR.
So save/restore these regs in the idle code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[ajd: Backport to 4.19 tree, CVE-2020-11669]
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc37a1632d upstream.
PowerVM systems running compatibility mode on a few Power8 revisions are
still vulnerable to the hardware defect that loses PMU exceptions arriving
prior to a context switch.
The software fix for this issue is enabled through the CPU_FTR_PMAO_BUG
cpu_feature bit, nevertheless this bit also needs to be set for PowerVM
compatibility mode systems.
Fixes: 68f2f0d431 ("powerpc: Add a cpu feature CPU_FTR_PMAO_BUG")
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.ibm.com>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200227134715.9715-1-desnesn@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2464cc4c34 upstream.
After a treclaim, we expect to be in non-transactional state. If we
don't clear the current thread's MSR[TS] before we get preempted, then
tm_recheckpoint_new_task() will recheckpoint and we get rescheduled in
suspended transaction state.
When handling a signal caught in transactional state,
handle_rt_signal64() calls get_tm_stackpointer() that treclaims the
transaction using tm_reclaim_current() but without clearing the
thread's MSR[TS]. This can cause the TM Bad Thing exception below if
later we pagefault and get preempted trying to access the user's
sigframe, using __put_user(). Afterwards, when we are rescheduled back
into do_page_fault() (but now in suspended state since the thread's
MSR[TS] was not cleared), upon executing 'rfid' after completion of
the page fault handling, the exception is raised because a transition
from suspended to non-transactional state is invalid.
Unexpected TM Bad Thing exception at c00000000000de44 (msr 0x8000000302a03031) tm_scratch=800000010280b033
Oops: Unrecoverable exception, sig: 6 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
CPU: 25 PID: 15547 Comm: a.out Not tainted 5.4.0-rc2 #32
NIP: c00000000000de44 LR: c000000000034728 CTR: 0000000000000000
REGS: c00000003fe7bd70 TRAP: 0700 Not tainted (5.4.0-rc2)
MSR: 8000000302a03031 <SF,VEC,VSX,FP,ME,IR,DR,LE,TM[SE]> CR: 44000884 XER: 00000000
CFAR: c00000000000dda4 IRQMASK: 0
PACATMSCRATCH: 800000010280b033
GPR00: c000000000034728 c000000f65a17c80 c000000001662800 00007fffacf3fd78
GPR04: 0000000000001000 0000000000001000 0000000000000000 c000000f611f8af0
GPR08: 0000000000000000 0000000078006001 0000000000000000 000c000000000000
GPR12: c000000f611f84b0 c00000003ffcb200 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000f611f8140
GPR24: 0000000000000000 00007fffacf3fd68 c000000f65a17d90 c000000f611f7800
GPR28: c000000f65a17e90 c000000f65a17e90 c000000001685e18 00007fffacf3f000
NIP [c00000000000de44] fast_exception_return+0xf4/0x1b0
LR [c000000000034728] handle_rt_signal64+0x78/0xc50
Call Trace:
[c000000f65a17c80] [c000000000034710] handle_rt_signal64+0x60/0xc50 (unreliable)
[c000000f65a17d30] [c000000000023640] do_notify_resume+0x330/0x460
[c000000f65a17e20] [c00000000000dcc4] ret_from_except_lite+0x70/0x74
Instruction dump:
7c4ff120 e8410170 7c5a03a6 38400000 f8410060 e8010070 e8410080 e8610088
60000000 60000000 e8810090 e8210078 <4c000024> 48000000 e8610178 88ed0989
---[ end trace 93094aa44b442f87 ]---
The simplified sequence of events that triggers the above exception is:
... # userspace in NON-TRANSACTIONAL state
tbegin # userspace in TRANSACTIONAL state
signal delivery # kernelspace in SUSPENDED state
handle_rt_signal64()
get_tm_stackpointer()
treclaim # kernelspace in NON-TRANSACTIONAL state
__put_user()
page fault happens. We will never get back here because of the TM Bad Thing exception.
page fault handling kicks in and we voluntarily preempt ourselves
do_page_fault()
__schedule()
__switch_to(other_task)
our task is rescheduled and we recheckpoint because the thread's MSR[TS] was not cleared
__switch_to(our_task)
switch_to_tm()
tm_recheckpoint_new_task()
trechkpt # kernelspace in SUSPENDED state
The page fault handling resumes, but now we are in suspended transaction state
do_page_fault() completes
rfid <----- trying to get back where the page fault happened (we were non-transactional back then)
TM Bad Thing # illegal transition from suspended to non-transactional
This patch fixes that issue by clearing the current thread's MSR[TS]
just after treclaim in get_tm_stackpointer() so that we stay in
non-transactional state in case we are preempted. In order to make
treclaim and clearing the thread's MSR[TS] atomic from a preemption
perspective when CONFIG_PREEMPT is set, preempt_disable/enable() is
used. It's also necessary to save the previous value of the thread's
MSR before get_tm_stackpointer() is called so that it can be exposed
to the signal handler later in setup_tm_sigcontexts() to inform the
userspace MSR at the moment of the signal delivery.
Found with tm-signal-context-force-tm kernel selftest.
Fixes: 2b0a576d15 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9
Signed-off-by: Gustavo Luiz Duarte <gustavold@linux.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200211033831.11165-1-gustavold@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1fb4124ca9 ]
When disabling virtual functions on an SR-IOV adapter we currently do not
correctly remove the EEH state for the now-dead virtual functions. When
removing the pci_dn that was created for the VF when SR-IOV was enabled
we free the corresponding eeh_dev without removing it from the child device
list of the eeh_pe that contained it. This can result in crashes due to the
use-after-free.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Tested-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190821062655.19735-1-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b5b9997b3 ]
On pseries there is a bug with adding hotplugged devices to an IOMMU
group. For a number of dumb reasons fixing that bug first requires
re-working how VFs are configured on PowerNV. For background, on
PowerNV we use the pcibios_sriov_enable() hook to do two things:
1. Create a pci_dn structure for each of the VFs, and
2. Configure the PHB's internal BARs so the MMIO range for each VF
maps to a unique PE.
Roughly speaking a PE is the hardware counterpart to a Linux IOMMU
group since all the devices in a PE share the same IOMMU table. A PE
also defines the set of devices that should be isolated in response to
a PCI error (i.e. bad DMA, UR/CA, AER events, etc). When isolated all
MMIO and DMA traffic to and from devicein the PE is blocked by the
root complex until the PE is recovered by the OS.
The requirement to block MMIO causes a giant headache because the P8
PHB generally uses a fixed mapping between MMIO addresses and PEs. As
a result we need to delay configuring the IOMMU groups for device
until after MMIO resources are assigned. For physical devices (i.e.
non-VFs) the PE assignment is done in pcibios_setup_bridge() which is
called immediately after the MMIO resources for downstream
devices (and the bridge's windows) are assigned. For VFs the setup is
more complicated because:
a) pcibios_setup_bridge() is not called again when VFs are activated, and
b) The pci_dev for VFs are created by generic code which runs after
pcibios_sriov_enable() is called.
The work around for this is a two step process:
1. A fixup in pcibios_add_device() is used to initialised the cached
pe_number in pci_dn, then
2. A bus notifier then adds the device to the IOMMU group for the PE
specified in pci_dn->pe_number.
A side effect fixing the pseries bug mentioned in the first paragraph
is moving the fixup out of pcibios_add_device() and into
pcibios_bus_add_device(), which is called much later. This results in
step 2. failing because pci_dn->pe_number won't be initialised when
the bus notifier is run.
We can fix this by removing the need for the fixup. The PE for a VF is
known before the VF is even scanned so we can initialise
pci_dn->pe_number pcibios_sriov_enable() instead. Unfortunately,
moving the initialisation causes two problems:
1. We trip the WARN_ON() in the current fixup code, and
2. The EEH core clears pdn->pe_number when recovering a VF and
relies on the fixup to correctly re-set it.
The only justification for either of these is a comment in
eeh_rmv_device() suggesting that pdn->pe_number *must* be set to
IODA_INVALID_PE in order for the VF to be scanned. However, this
comment appears to have no basis in reality. Both bugs can be fixed by
just deleting the code.
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191028085424.12006-1-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9101bfa6a ]
__find_linux_mm_pte() returns a page table entry pointer after walking
the page table without holding locks. To make it safe against a THP
split and/or collapse, we disable interrupts around the lockless page
table walk. However we need to keep interrupts disabled as long as we
use the page table entry pointer that is returned.
Fix addr_to_pfn() to do that.
Fixes: ba41e1e1cc ("powerpc/mce: Hookup derror (load/store) UE errors")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Rearrange code slightly and tweak change log wording]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190918145328.28602-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4aa219a07 ]
Allow external callers to force the cacheinfo code to release all its
references to cache nodes, e.g. before processing device tree updates
post-migration, and to rebuild the hierarchy afterward.
CPU online/offline must be blocked by callers; enforce this.
Fixes: 410bccf978 ("powerpc/pseries: Partition migration in the kernel")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michal Suchanek